The length of the WMM Action frame was not properly validated and the
length of the information elements (int left) could end up being
negative. This would result in reading significantly past the stack
buffer while parsing the IEs in ieee802_11_parse_elems() and while doing
so, resulting in segmentation fault.
This can result in an invalid frame being used for a denial of service
attack (hostapd process killed) against an AP with a driver that uses
hostapd for management frame processing (e.g., all mac80211-based
drivers).
Thanks to Kostya Kortchinsky of Google security team for discovering and
reporting this issue.
Signed-off-by: Jouni Malinen <j@w1.fi>
The debug information from httpread can be helpful in figuring out error
cases in general and as such, should be enabled by default. Get rid of
the hardcoded httpread_debug value that would require source code
changes to enable.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to continue processing a HTTP body when it becomes
clear that the end result would be over the maximum length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that ncopy parameter to memcpy is not negative. While this is not
supposed to be needed, it is a good additional protection against
unknown implementation issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
strtoul() return value may end up overflowing the int h->chunk_size and
resulting in a negative value to be stored as the chunk_size. This could
result in the following memcpy operation using a very large length
argument which would result in a buffer overflow and segmentation fault.
This could have been used to cause a denial service by any device that
has been authorized for network access (either wireless or wired). This
would affect both the WPS UPnP functionality in a WPS AP (hostapd with
upnp_iface parameter set in the configuration) and WPS ER
(wpa_supplicant with WPS_ER_START control interface command used).
Validate the parsed chunk length value to avoid this. In addition to
rejecting negative values, we can also reject chunk size that would be
larger than the maximum configured body length.
Thanks to Kostya Kortchinsky of Google security team for discovering and
reporting this issue.
Signed-off-by: Jouni Malinen <j@w1.fi>
While being associated, if an ANQP request is received for a different
AP that doesn't exist in the BSS list, the ANQP request will be sent on
the frequency of the AP that we are currently associated to.
In such a case, it is possible that the ANQP request would be sent on
a channel different than that of the requested AP, potentially delaying
other requests/activities.
Avoid sending the ANQP request to an AP that is not in the BSS list.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Fix memory leak introduced in commit
32a097fdd2 ("wpa_cli: Keep track of
available networks") by tracking networks only when in interactive mode.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add the TDLS_LINK_STATUS command to the control interface. This command
shows what is the status of our current TDLS connection with the given
peer. Also, add the TDLS_LINK_STATUS command to wpa_cli.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Sanity check added to avoid segmentation fault which occurs, when
issuing ibss_rsn ctrl iface cmd and IBSS was not initialized previously
via IBSS network selection.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
If the mp_init_multi() call had failed due to memory allocation failure,
mp_div() would have returned 1 instead of MP_MEM (-2). It looks like all
callers are checking the return value against MP_OKAY instead of <1
(etc.), so this does not seem to result in difference in behavior.
Anyway, it's best to fix the mp_div() return value for the MP_MEM error
case to avoid unexpected behavior.
Signed-off-by: Maks Naumov <maksqwe1@ukr.net>
In theory, the previous version could have resulted in reading one byte
beyond the end of the management frame RX buffer if the local driver
were to deliver a truncated Public Action frame for processing. In
practice, this did not seem to happen with mac80211-based drivers and
even if it were, the extra octet would be an uninitialized value in a
buffer rather than read beyond the end of the buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was previously checked as part of the eap_sim_parse_attr()
processing, but it is easier to review the code if there is an
additional explicit check for confirming that the Reserved field is
present since the pos variable is advanced beyond it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Couple of the EAP-SIM/AKA protocol test cases were leaving out the
Reserved field. This was not intentional since these test cases were
targeting a specific Subtype processing instead of verifying truncated
header case (which is covered separately). Add the Reserved field to
allow the implementation to add an explicit, earlier check for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
Clean up eap_sake_parse_add_attr() design by passing in pointer to the
payload of the attribute instead of parsing these separately for each
attribute within the function.
Signed-off-by: Jouni Malinen <j@w1.fi>
The req_plen argument to eap_pax_process_std_1() and
eap_pax_process_std_3() could be smaller than sizeof(struct eap_pax_hdr)
since the main processing function was only verifying that there is
enough room for the ICV and then removed ICV length from the remaining
payload length.
In theory, this could have resulted in the size_t left parameter being
set to a negative value that would be interpreted as a huge positive
integer. That could then result in a small buffer read overflow and
process termination if MSGDUMP debug verbosity was in use.
In practice, it does not seem to be feasible to construct a short
message that would be able to pass the ICV validation (calculated using
HMAC-SHA1-128) even for the case where an empty password is used.
Anyway, the implementation should really check the length explicitly
instead of depending on implicit check through ICV validation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The EAP-TLS-based helper functions can easily use struct wpabuf in more
places, so continue cleanup in that direction by replacing separate
pointer and length arguments with a single struct wpabuf argument.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function is only using the Identifier field from the EAP request
header, so there is no need to pass it a pointer to the full message.
This makes it a bit easier to analyze the area that gets access to
unverified message payload.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit c2762e410f ('P2P: Update D-Bus
network object semantics during group formation') added this helper
function to determine whether a network block is used for storing a
persistent group information. However, it implemented this in a way that
matches both persistent group storage and an operating persist group
instance. This does not seem to match the expected behavior for the
D-Bus objects, so fix this to match only the persistent group storage
case to avoid registering/unregistered incorrect D-Bus objects for
groups.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit bb3df9a569 ('notify: Do not raise
any signal from a P2P management interface') was supposed to only change
D-Bus behavior, but it ended up disabling non-D-Bus functionality as
well for some sequences where the P2P Device interface is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Number of the P2P test cases through D-Bus commands were not prepared
for there being a separate group interface when the P2P Device concept
is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 21efc940f6 ('wpa_supplicant: Do not
register a P2P management interface on DBus') hides the special P2P
management interface from D-Bus. However, it did not take into account
the possibility of wpa_s->dbus_path and wpa_s->dbus_new_path being NULL
in such cases on number of code paths within the D-Bus handlers. This
could result in invalid arguments (NULL path) being provided to D-Bus
functions (mainly, dbus_message_iter_append_basic) and NULL pointer
dereference when iterating over all interfaces. Either of these could
make wpa_supplicant process terminate.
Fix this by explicitly checking that the interface-specific D-Bus path
has been registered before using it anywhere with D-Bus handlers. In
addition, find the correct wpa_s instance to fix P2P operations through
D-Bus when the P2P Device interface is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MS-MPPE-Recv-Key generation in radius_msg_add_mppe_keys() used incorrect
function argument (send_key_len; should be recv_key_len) when allocating
a temporary buffer. Fix this by using the correct argument.
The only caller of the function uses the same length for both
send_key_len and recv_key_len, so this copy-paste error did not result
in any difference in the behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Handling of WPS RF band for 60 GHz was missing. Add it in all relevant
places and also map "AES" as the cipher to GCMP instead of CCMP when
operating on the 60 GHz band.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Commit 5add410162 ('WPS: Use shorter
authentication timeout during no-SelReg iteration') added a new
condition on reducing the authentication timeout for the WPS AP
iteration process. However, due it ended up copy-pasting an incorrect
condition for this. This was supposed to apply for PIN-based config
method advertisement, not PBC.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the WPA_ALG_PMK algorithm in set_key() to result in
trying to configure a key with cipher suite 0. While this results in a
failure from cfg80211 or driver, this is not really desirable operation,
so add a check for cipher suite conversion result before issuing the
nl80211 command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, it was possible for the set_key() handler to be used with
WPA_ALG_PMK even if the driver did not indicate support for key
management offload. While this is not really supposed to result in any
difference, it makes the debug logs somewhat confusing. Avoid that by
using driver capability flag for key management offload as an additional
condition for setting the PMK.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This can be used with Proxy ARP to allow multicast NAs to be forwarded
to associated STAs using link layer unicast delivery. This used to be
hardcoded to be enabled, but it is now disabled by default and can be
enabled with na_mcast_to_ucast=1. This functionality may not be desired
in all networks and most cases work without it, so the new
default-to-disabled is more appropriate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
interworking_credentials_available_3gpp() would have left excluded2
uninitialized without INTERWORKING_3GPP in the build. This could result
in a static analyzer warning within
interworking_credentials_available_helper() about use of uninitialized
variable. Get rid of that warning by explicitly initializing excluded2
even though this does not really result in any difference in behavior
since the excluded2 value would be used only if the non-NULL is returned
and that could not have been the case here without INTERWORKING_3GPP.
Signed-off-by: Jouni Malinen <j@w1.fi>
Enhance test ap_vlan_wpa2_radius_id_change to change the VLAN-ID
back as a last step. This ensures that the wpa_group for VLAN-ID 1
did not enter FATAL_FAILURE state during the test.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Previously, struct wpa_group was created when the first station enters
the group and the struct wpa_group was not freed when all station left
the group. This causes a problem because wpa_group will enter
FATAL_FAILURE when a wpa_group is running while the AP_VLAN interface
has already been removed.
Fix this by adding a reference counter to struct wpa_group and free a
group if it is unused.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
In addition, this adds some delay between the authentication and data
connectivity test through the newly added VLAN and by doing so, makes
ap_vlan_wpa2_radius_id_change a bit more robust. It was possible for the
EAPOL-Key message 4/4 not having yet been processed by hostapd at the
time the data test started.
Signed-off-by: Jouni Malinen <j@w1.fi>
If hostapd has bound a STA into a specific VLAN, the new vlan_id
parameter in the control interface STA command can now be used to check
which VLAN ID is in use.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for an nl80211-based driver to be determined to support
P2P even when the radio supports only the 5 GHz band. This resulted in
P2P initialization failing due to not being able to pick a social
channel and wpa_supplicant not starting. Fix this by not enabling P2P,
but still allowing wpa_supplicant initialization to complete.
Signed-off-by: Jouni Malinen <j@w1.fi>
All the system header files are supposed to be included before any other
internal header file apart from utils/includes.h.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signal strength meter uses non-standard icons (not included in the
freedesktop icon specification), which might not be available in all
icon sets on the market. What's more, according to the latest Ubuntu
practices, in the status-like places one should use symbolic icons.
Unfortunately not all icon sets provide them.
In order to overcome this inconsistency, we are going to try to load
more than one icon from the current theme in the fallback-like
fashion.
Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
