Commit graph

2895 commits

Author SHA1 Message Date
Ilan Peer
28812a8983 P2P: Try using one of the social channels for GO
In case there is no preference for the GO operating channel,
try using one of 1, 6, 11 (randomly), and only if the random
selection is not suitable traverse all the channels 1..11.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-06-15 00:33:52 +03:00
Avraham Stern
0a816e8cbf P2P: Remove duplicated code from get_shared_radio_freqs_data()
Remove the seperation between getting the local interface frequency and
other interfaces frequencies since going over all the radio interfaces
includes the local interface.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2014-06-15 00:21:41 +03:00
Jouni Malinen
504df28a1d Remove unused dump_freq_array()
This function is not used anymore.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-15 00:21:41 +03:00
Ilan Peer
a0c90bb073 P2P: Collect and use extended data on used frequencies
When the number of frequencies supported by the kernel is bigger than
one, and there is a need to pick a frequency for a new flow such as P2P
GO Negotiation or P2P Invitation, the flow should be able to pick the
best frequency among all the frequencies currently used by the device.

In order to prioritize between the currently used frequencies, add
the ability to collect additional data about each used frequency
(if the frequency is used by a station interface or P2P Client)
and when needed select the best frequency, where:

1. Infrastructure interfaces have highest priority
2. P2P Client interfaces have higher priority over AP/GO
   interfaces.

The rational is that the frequency of an AP/GO can change while
that of a station interface cannot.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-06-15 00:21:40 +03:00
Avraham Stern
b278f323ed P2P: Remove unused code from get_shared_radio_freqs_data()
Remove the check for get_radio_name support from
get_shared_radio_freqs_data() since get_radio_name is no longer in use
in this function.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2014-06-15 00:21:40 +03:00
Jouni Malinen
25be28a375 dbus: Check return value more consistently (CID 62841)
Most of these calls are checked to return success and there is no reason
why these wouldn't, so be more consistent. This addresses CID 62841,
CID 62840, CID 62839, CID 62838, CID 62837, CID 62836.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-14 12:32:53 +03:00
Jouni Malinen
f62415df8a Note chmod() failure in debug log even in ignore case (CID 62843)
If this chmod() call fails, the global control interface is allowed to
be used since there was no change to its group. Anyway, it can be
helpful to note the error case in debug log instead of silently ignoring
it.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-14 12:32:52 +03:00
Jouni Malinen
49d13df63c P2P: Fix wfd_dev_info parsing for P2P-DEVICE-FOUND (CID 68127)
Commit b125c48fce ('P2P: Add wfd_dev_info=
field for device found event') added Wi-Fi Display device info to the
P2P-DEVICE-FOUND events. However, it did not include proper bounds
checking in wifi_display_subelem_hex() and could accept subelements with
invalid length field values. This could result in buffer read overflow
of up to 64 kB and inclusion of heap memory in the local control
interface event and/or process crash due to invalid memory access. Fix
this by checking the validity of the length field before writing a
hexdump of the data.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 15:25:39 +03:00
Jouni Malinen
1851e17a64 dbus: Clean up P2P group vendor ext getter
The vendor_ext[i] = NULL setting did not make any sense since
num_vendor_ext should have been used to index the vendor_ext array. The
old code did not do any harm since i >= num_vendor_ext and none of the
already set entries could have been cleared. Anyway, better clean this
by making it skip the setting to NULL similarly to what was already done
in the P2P peer vendor ext getter.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:48:21 +03:00
Jouni Malinen
137ff332fd HS 2.0R2: Fix OSEN IE parsing for in cipher setup (CID 68132)
The OSEN code path hardcodes number of struct wpa_ie_data items.
However, it did not clear the full structure and some uninitialized
fields could have been used (e.g., ie.mgmt_group_cipher for a debug
print and ie.capabilities for checking MFPC). Fix this by clearing the
ie data before filling in the hardcoded OSEN values.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:36:42 +03:00
Jouni Malinen
2703fb4ad9 WNM: Use cleaner way of generating pointer to a field (CID 68100)
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:27:15 +03:00
Jouni Malinen
fb5d417178 P2P: Use cleaner way of generating pointer to a field (CID 68096)
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:27:15 +03:00
Jouni Malinen
35c03184df P2P: Use cleaner way of generating pointer to a field (CID 68095)
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:27:15 +03:00
Jouni Malinen
e987c70c85 dbus: Add explicit break statements to switch-default
There were couple of missing breaks in switch-default (before/after).
While these did not have any noticeable issues due to falling over to
the next step that just exited from the switch statement, it is cleaner
and more robust to have each case use an explicit break.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:27:15 +03:00
Jouni Malinen
6446420b24 dbus: Initialize temporary entry properly (CID 62877)
The tmpentry variable was not initialized and
_wpa_dbus_dict_entry_get_byte_array() does not set tmpentry.type, so it
would have been possible for the error path to end up trying to free
unexpected type of an entry or not free the memory at all.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:27:15 +03:00
Jouni Malinen
70d9537361 Use clearer way of getting pointer to a frame (CID 62835)
This avoids an incorrect ARRAY_VS_SINGLETON report for a case where a
pointer is taken to the specified field in a frame and not to a single
octet. Bounds checking was already handled separately.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:27:11 +03:00
Jouni Malinen
0e87e798b5 Fix HS20_GET_NAI_HOME_REALM_LIST hex length check (CID 68108)
Due to an incorrect operation (MOD vs. AND), the code that was supposed
to return an error if the hex string has odd length was not really
reporting any failures. Instead of reporting an error, the invalid
control interface command would have been truncated. This is not an
issue in practice, but better fix the implementation anyway.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-12 19:45:27 +03:00
Jouni Malinen
beb9e1171e dbus: Avoid theoretical memory leaks with duplicated dict entries
If a dict would include duplicated items, the parsing code here would
have leaked memory by overwriting old os_strdup() result with the new
one. Fix this by explicitly freeing the previous entry. This addresses
CID 62852, CID 62851, CID 62850, CID 62849, CID 62847, CID 62846.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-12 19:45:06 +03:00
Jouni Malinen
ceb4cd89c9 dbus: Fix a potential double-free in on error path (CID 62880)
It would have been at least theoretically possible to hit the first
error in the loop and end up jumping to error handling which would call
os_free(value) without the value having been cleared after the os_free()
call at the end of the previous loop iteration.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-12 19:45:02 +03:00
Jouni Malinen
5519241676 GAS: Limit TX wait time based on driver maximum value
The GAS query TX operation used a fixed wait time of 1000 ms for the
reply. However, it would be possible for the driver to not support this
long remain-on-channel maximum. Limit this wait time based on driver
support, if needed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-12 10:56:06 +03:00
Nirav Shah
d3b204694a P2P: Make the default p2p_find delay value configurable
This makes the p2p_find default delay value configurable as
p2p_search_delay parameter through the configuration file (and through
control interface "SET p2p_search_delay <value>" on the P2P management
interface.

This parameter controls the number milliseconds of extra delay that is
added between search iterations when there is a concurrent operation in
progress. This can be used, e.g., p2p_search_delay=100 to make p2p_find
friendlier to concurrent operations by avoiding it from taking 100% of
the radio resources. The default value is the previous default, i.e.,
500 ms. Smaller values can be used to find peers more quickly at the
cost of larger effect to concurrent operations while a larger value
leaves more time for the concurrent operations at the cost of making
device discovery take longer time.

The optional p2p_find delay argument can still be used to override the
search delay for each search operation.

Since the P2P_CONCURRENT_SEARCH_DELAY macro is not used anymore, the
driver specific build parameter for bcmdhd from Android.mk is also
removed. Similar configuration can now be achieved with
p2p_search_delay=0 in the p2p0 interface configuration file.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-09 19:43:26 +03:00
Jouni Malinen
a01acc50d5 Check for EVENT_ASSOC data to be present for AP mode operation
wpa_supplicant_event() is required to include the event data for AP mode
events. In theory, a non-AP mode event could be sent here from the
driver wrapper, so reject such event.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 19:15:50 +03:00
Jouni Malinen
0bbaa9b93f Validate driver extended capabilities length against buffer length
Prepare for new extended capabilities bits by checking that the local
buffer is large enough to contain all the bits the driver requests. The
existing buffers are large enough to include anything defined until now,
but it would be possible to add more definitions in the future, so
increase them a bit as well to make this more future proof.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 16:35:30 +03:00
Jouni Malinen
9c6c5589e0 Interworking: Reject EAP configuration with unsupported inner method
Instead of allowing the connection attempt to occur with an unsupported
inner method, check for that explicitly at the time the network block is
added and drop the network if the identified inner method is not
supported.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 16:18:30 +03:00
Jouni Malinen
f2ca0e9770 Check eap_get_name() return against NULL to silence static analyzer
This cannot really be NULL in practice since cred->eap_method would
point to a valid EAP method. Anyway, to avoid false positive from
analyzers, check the pointer explicitly before printing it.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 15:42:07 +03:00
Jouni Malinen
fb958ea76e Check current_ssid on unexpected association event
This is mainly to keep static analyzers silent since it does not look
like this code path can be reached in practice due to the way
association events are handled and current_ssid is either set before
resched here or the association is rejected. Anyway, if this could be
reached, the wpa_supplicant_set_wpa_none_key() call would end up
dereferencing a NULL pointer, so add an explicit check to make sure that
does not happen.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-07 13:32:13 +03:00
Jouni Malinen
6a98f67369 ChangeLog entries for v2.2
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-04 16:08:37 +03:00
Jouni Malinen
d4b951f31b Fix offchannel TX not to retransmit pending frame on callback
If the offchannel TX frame command was offloaded to the driver in
offchannel_send_action(), we must not send another copy of the frame if
a remain-on-channel event happens to be delivered between this TX
command and the matching TX status event. It was possible for the
duplicated frame to cause problems, e.g., with P2P invitation exchange
if the same Invitation Request frame got sent twice and only the first
one getting accepted by the peer.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-04 16:07:59 +03:00
Jouni Malinen
df48efc5ab Fix external radio work stopping to not read freed memory
The dynamically allocated struct wpa_external_work contains the name of
the radio work in the type field and this is used in a debug print
within radio_work_done(). Re-order radio_work_done() and os_free() calls
on couple of paths where the memory was freed before that final user of
the buffer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-31 22:58:51 +03:00
Amit Khatri
9a17b36e55 tests: Makefile change avoiding compiler error for module test
wpa_supplicant was giving below error when "CONFIG_MODULE_TESTS=y" and
"CONFIG_P2P=y" are in .config file:
"wpas_module_tests.c:84: undefined reference to `wps_module_tests'"

This error is coming because "CONFIG_WPS=y" is commented out in .config
file but CONFIG_WPS is getting enabled by CONFIG_P2P in Makefile.

Signed-off-by: Amit Khatri <amit.khatri@samsung.com>
2014-05-31 13:36:59 +03:00
Mikael Kanstrup
b77aeae732 Interworking: Re-trigger scan if no connect attempt is done
For one specific case when running with Interworking enabled the
re-initialisation of the scan timer is missing. This makes auto connect
to a configured network fail.

The case is:
- Interworking credentials available, but do not match
- Auto interworking is enabled (auto_interworking=1)
- Interworking auto select is disabled (i.e., this is from
  auto_interworking=1, not from INTERWORKING_SELECT auto)
- No configured (enabled and non blacklisted) networks are present
  in scan results list with full match
- Interworking finds matching networks (it does not do full security
  policy match)

This patch covers the case and re-initialises the scan timer to allow
search for a suitable network to continue.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
2014-05-31 13:23:00 +03:00
Jouni Malinen
2d2dd488be tests: Add module tests for src/common
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-28 00:56:13 +03:00
Jouni Malinen
829a1b3296 P2P: Clear p2p_auth_invite after each persistent group invitation
This makes the operations more consistent when going through multiple
persistent group re-invocation sequences in a row. Each invitation needs
to be accepted separately if persistent reconnect is not enabled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-27 12:09:25 +03:00
Boris Sorochkin
e403ba859e Parse DMG capabilities when reporting to external interfaces
This adds [DMG] and [PBSS] flags for scan results and BSS table entries
using the IEEE Std 802.11ad-2012 updated definition of the Capability
field.

Signed-off-by: Boris Sorochkin <qca_bsoroc@qca.qualcomm.com>
2014-05-26 23:35:52 +03:00
Jouni Malinen
8860e0f47c tests: Add printf encoding/decoding module tests
This replaces tests/test-printf.c.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-26 17:21:44 +03:00
Jouni Malinen
7bb70909a2 Add DRIVER_EVENT AVOID_FREQUENCIES for testing
This can be used to simulate driver events indicating frequencies to
avoid.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-26 17:21:44 +03:00
Masashi Honma
f0356ec85c eloop: Add epoll option for better performance
This patch adds epoll option for the eloop implementation. This can be
selected with the CONFIG_ELOOP_EPOLL=y build option.

[merit]
See Table1.

Table1. comparison table
+--------+--------+-----------+------------+-------------+
|        | add fd | remove fd | prepare fd | dispatch fd |
+--------+--------+-----------+------------+-------------+
| select | O(1)   | O(1)      | O(N)       | O(N)        |
+--------+--------+-----------+------------+-------------+
| poll   | O(1)   | O(1)      | O(N)       | O(N)        |
+--------+--------+-----------+------------+-------------+
| epoll  | O(1)   | O(1)      | 0          | O(M)        |
+--------+--------+-----------+------------+-------------+
"add fd" is addition of fd by eloop_sock_table_add_sock().
"remove fd" is removal of fd by eloop_sock_table_remove_sock().
"prepare fd" is preparation of fds before wait in eloop_run().
"dispatch fd" is dispatchment of fds by eloop_sock_table_dispatch().
"N" is all watching fds.
"M" is fds which could be dispatched after waiting.

As shown in Table1, epoll option has better performance on "prepare fd" column.
Because select/poll option requires setting fds before every select()/poll().
But epoll_wait() doesn't need it.

And epoll option has also better performance on "dispatch fd" column.
Because select/poll option needs to check all registered fds to find out
dispatchable fds. But epoll option doesn't require checking all registered fds.
Because epoll_wait() returns dispatchable fd set.

So epoll option is effective for GO/AP functionality.

[demerit]
The epoll option requires additional heap memory. In case of P2P GO, it is
about 8K bytes.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-05-16 18:25:51 +03:00
Tomasz Bursztyka
68d270069f dbus: No need to recompute group object path on GroupStarted signal
The group object is already registered on DBus at that point, thus wpa_s
structure holds its path already.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-05-16 18:20:17 +03:00
Tomasz Bursztyka
f3734e2377 dbus: Provide the P2P Device Address from the relevant structure
Fixes a minor mistake: the p2p_info structure should be used here
instead of the peer_handler_args one.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-05-16 18:19:37 +03:00
Tomasz Bursztyka
e956b830fc dbus: Fix interface DeviceFound signal specification
DeviceFound does not provide any properties, just the peer object path.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-05-16 18:19:10 +03:00
Tomasz Bursztyka
fc591a771c dbus: Declare GONegotiation signals properly
These signals delivers an array of key/value pairs, thus declaring those
as it should.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-05-16 18:18:39 +03:00
Dmitry Shmidt
b19c098e75 Send authentication failure reason in wpas_auth_failed()
"WRONG_KEY"   - possibly wrong psk
"AUTH_FAILED" - authentication failure
"CONN_FAILED" - continiuos connection failure

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-05-16 18:08:39 +03:00
Eduardo Abinader
5516ed32c5 WPS: Deinit before wpas_p2p_disconnect()
When there is a pending WPS negotiation for P2P and signal interrupt is
triggered, invalid read occurs in wpas_wps_terminate_pending() if
wpas_p2p_disconnect() removed the interface. Inverting deinit order
solves the issue.

Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
2014-05-16 01:03:44 +03:00
Jouni Malinen
e9eb648e0e P2P: Reject P2P_FIND and P2P_LISTEN on disabled interface
This makes the P2P operations behave more consistently with the SCAN
command.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-15 21:34:32 +03:00
Jouni Malinen
c71c241674 P2P: Clear P2P state if active interface is disabled
The radio works for the interface get removed if interface is disabled.
This could have left P2P module in invalid state if the interface got
disabled during a p2p_find or p2p_listen operation. Clear the state in
such a case to avoid blocking following operations due to P2P module
assuming it is still in progress of doing something.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-15 21:32:54 +03:00
Jouni Malinen
ad12f2f422 Add DRIVER_EVENT ctrl_iface command for testing purposes
This new command can be used to simulate driver events without having to
go through the driver wrapper or kernel code for this. This enables more
testing coverage with hwsim.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-15 21:09:48 +03:00
Jouni Malinen
3e66f78914 P2P: Make sure GO start does not miss connect_without_scan
It looks like there was a possible sequence for wpa_s->scan_req to be
MANUAL_SCAN_REQ at the moment a GO is to be started. This could result
in the "Request scan (that will be skipped) to start GO" to actually not
skip the scan and end up stuck waiting for something external to trigger
a scan before the GO could be started. Fix this by clearing
wpa_s->scan_req when deciding to start the GO.

This issue could be hit at least by first enabling autoscan and then
issuing P2P_GROUP_ADD. Other sequences that set wpa_s->scan_req to
MANUAL_SCAN_REQ without going through wpa_supplicant_scan() to clear it
immediately could also have similar effect (and there is even a small
window for the wpa_supplicant_scan() call to happen only after the
P2P_GROUP_ADD command is processed, so this could potentially have
happened even with SCAN + P2P_GROUP_ADD).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-15 16:56:49 +03:00
Rashmi Ramanna
28fa4eb2b2 P2P: Fix scan optimization for GO during persistent group invocation
Commit 41d5ce9e0b was intended to scan for
GO on the negotiated channel for few iterations, but it did not work
correctly due to incorrect operator being used. Fix this by requiring
both conditions to be met for the single channel scan.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-13 15:49:06 +03:00
Edhar, Mahesh Kumar
7b42862ac8 P2P: Validate GO operating channel on channel list changes
On receiving CHANNEL_LIST_CHANGED event from driver, verify that local
GO (if any) is operating in valid frequency. If not, we should remove
the group and reform on valid frequency. Indicate this similarly to the
avoid-frequency notification (i.e., a control interface message for
upper layers to react to this for now; potentially CSA later).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-12 19:43:59 +03:00
Alexandru Costache
fb2ac53df1 Remove leftover timeouts on cleanup
Signed-off-by: Alexandru Costache <alexandru.costache.100@gmail.com>
2014-05-12 19:43:59 +03:00
Dmitry Shmidt
1c330a2fdc Add 'dup_network <id_s> <id_d> <name>' command
This command allows to copy network variable from one network to
another, e.g., to clone the psk field without having to extract it from
wpa_supplicant.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-05-12 19:43:56 +03:00
Hannu Mallat
316f92cd33 dbus: Reorder deauthentication and cleanup calls when removing a network
Valgrind indicates reference to already freed memory if function
wpa_config_remove_network() is called prior to calling
wpa_supplicant_deauthenticate(), and this can lead to a crash.
Inverting the call order fixes the problem.

Signed-off-by: Hannu Mallat <hannu.mallat@jollamobile.com>
2014-05-12 18:05:38 +03:00
Jouni Malinen
cfdb32e88f eapol_test: Check EAP-Key-Name
The new command line argument -e can be used to request the server to
send EAP-Key-Name in Access-Accept. If both the local EAP peer
implementation and server provide the EAP Session-Id, compare those
values and indicate in debug log whether a match was seen.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-11 21:22:37 +03:00
Jouni Malinen
270c9a43e6 Interworking: Allow FT to be used for connection
This extends Interworking network selection to enable FT-EAP as an
optional key_mgmt value to allow FT to be used instead of hardcoding
WPA2-Enterprise without FT.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-10 16:15:20 +03:00
Eduardo Abinader
81ed4991ae Remove duplicated ibss_rsn_deinit() call
No need to call ibss_rsn_deinit() again since it is already being called
by wpa_supplicant_mark_disassoc().

Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
2014-05-10 13:48:34 +03:00
Sunil Dutt
0f1034e388 P2P: Refrain from performing extended listen during P2P connection
Do not perform extended listen period operations when either a P2P
connection is in progress. This makes the connection more robust should
an extended listen timer trigger during such an operation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-09 20:42:44 +03:00
Hu Wang
dd10abccc8 MACsec: wpa_supplicant integration
Add MACsec to the wpa_supplicant build system and configuration file.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-09 20:42:44 +03:00
Hu Wang
7baec808ef MACsec: Add driver_ops
This defines new driver_ops to be used with MACsec.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-09 20:05:28 +03:00
Hu Wang
0836c04b30 MACsec: Allow EAPOL version 3 to be configured
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-09 20:05:28 +03:00
Jouni Malinen
2cebdee66d Fix MinGW build
No need to use ENOBUFS within core wpa_supplicant, so just replace it
with -1 to work arounds MinGW build issues.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-29 18:59:12 +03:00
Eliad Peller
e4fa8b120b wpa_supplicant: Add Wake-on-WLAN configuration support
Add a new wowlan_triggers option to wpa_supplicant.conf. The triggers in
this key will be used to configure the kernel wowlan configuration.

For now, support only simple flags. More complex triggers can be added
later on.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2014-04-29 18:59:12 +03:00
Dmitry Shmidt
959214b260 Android: Use extended P2P functionality (ANDROID_P2P) for all vendors
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-04-29 18:59:12 +03:00
Sreenath Sharma
fa258a3df6 HS 2.0 R2: Fix writing of domain_suffix_match cred parameter
This was supposed to end with a newline character so that parameters are
aligned in configuration file.

Signed-off-by: Sreenath Sharma <sreenats@broadcom.com>
2014-04-29 17:25:19 +03:00
Jouni Malinen
0bceb8d6f4 Make dl_list_first() and dl_list_last() uses easier for static analyzers
The previous check for dl_list_len() or having an entry from the list is
sufficient, but some static analyzers cannot figure out that
dl_list_first() and dl_list_last() will return non-NULL in this type of
cases. Avoid invalid reports by explicitly checking for NULL.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-29 12:52:10 +03:00
Jouni Malinen
ece88f7697 Make last_scan_res update easier for static analyzers
The check based on last_scan_res_used is sufficient for making sure that
last_scan_res is allocated. However, it is a bit too complex for static
analyzers to notice, so add an explicit check to avoid bogus reports.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-29 12:52:10 +03:00
Jouni Malinen
b7a6702fd4 Indicate disconnection event on interface disabled
It is possible for the disconnection event from the driver to not get
delivered when interface is disabled. To maintain consistent ctrl_iface
event behavior, indicate CTRL-EVENT-DISCONNECTED in such a case if we
were in connected state.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-28 16:54:09 +03:00
Jouni Malinen
b89962b4b9 Fix wpa_config_read() with existing config block
If two config files are merged together, the ssid and cred blocks may
not have been processed correctly since the tail pointers were not
updated to the last entry from the first configuration file.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-28 16:54:09 +03:00
Ilan Peer
d0df643735 wpa_supplicant: Call frequency conflict handling during auth
Previously, the frequency conflict was handled only during the
association flow. However, some drivers, e.g., mac80211 based
drivers, will fail an authentication request in case that there
are no available channels for use (as they might be used by
other interfaces), and thus the frequency conflict resolution
is never called.

Fix this by calling frequency conflict resolution during
authentication (SME-in-wpa_supplicant) as well.

In addition, get the shared radio frequency from the wpa_s context in
both the SME-in-driver and SME-in-wpa_supplicant cases and not from the
driver.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-04-24 12:15:32 +03:00
Luciano Coelho
0cf24fdaed scan: Reset normal scan counter when a connection succeeds
The normal scan counter is used to trigger a few normal scans before a
scheduled scan is issued. The reason for doing this is that we get
results faster and some drivers support more SSIDs per normal scan
than during sched scan. After 2 normal scans, we start using
sched_scan. But the problem is that when a connection succeeds, we do
not reset this counter, so we will keep using sched scans.

To fix this, now we reset the counter when we switch to WPA_COMPLETED
state.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
2014-04-24 12:15:32 +03:00
Greg Hackmann
9176ec066e Android: Disable unused parameter warnings
This avoids large number of undesired compiler warnings since Android
build system is added -Wextra.

Signed-off-by: Greg Hackmann <ghackmann@google.com>
2014-04-24 12:15:32 +03:00
Naresh Jayaram
13f6a07efc Add SIM identifier to the network profile and cred block
This allows the specific SIM to be identified for authentication
purposes in multi-SIM devices. This SIM number represents the index of
the SIM slot. This SIM number shall be used for the authentication using
the respective SIM for the Wi-Fi connection to the corresponding
network.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-24 12:15:32 +03:00
Jouni Malinen
d41cc8ccf6 Allow HT 40 MHz intolerant flag to be set for association
This extends HT overrides to allow HT 40 MHz intolerant flag to be set
with ht40_intolerant=1.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-17 17:11:17 +03:00
Jouni Malinen
f777fd127f Fix writing of provisioning_sp cred parameter
This was supposed to be within quotation marks in the configuration
file.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-16 01:41:38 +03:00
Jouni Malinen
a7ca6dac44 Fix P2P redirection of global ctrl_iface SET command
The previous version prevented all use of wpas_global_ctrl_iface_set().
That's not desirable since there may be more global parameters added in
the future. Instead, try to use the global version first and redirect to
P2P interface only if the global version returns an error.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-15 13:27:23 +03:00
Jouni Malinen
d6b818efe5 Remove SAVE_CONFIG redirect from global control interface
The P2P redirection for SAVE_CONFIG issued on the global control
interface was preventing wpas_global_ctrl_iface_save_config() from being
reached. The global version of SAVE_CONFIG was supposed to try to save
configuration files for all interface rather than just the P2P
management interface, so fix this by removing the unneeded and undesired
redirection.

Modify the global SAVE_CONFIG handler to return FAIL if no configuration
files were saved. This makes the behavior match with the per-interface
SAVE_CONFIG.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-15 13:26:48 +03:00
Jouni Malinen
128cc37558 eap_proxy: Use unique Makefile names for Android and non-Android
Rename the eap_proxy_*.mk file to eap_proxy_*.mak for non-Android builds
so that the same eap_proxy implementation can be more easily included in
the same directory for both cases.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-15 13:02:25 +03:00
Jouni Malinen
e83e15ee77 P2P: Fix interface remove to terminate all P2P groups
Previously, it was possible to remove the main interface and leave
behind dynamic P2P group interfaces. This would eventually result in
references freed memory, so it is not really suitable behavior. Instesd,
remove all the dynamic P2P group interfaces that were created through an
interface that is now removed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-15 00:20:17 +03:00
quiche@chromium.org
e9b32dae1a Propagate scan failures over D-Bus
If we receive a scan request via D-Bus and wpa_supplicant_scan_trigger
fails, return the failure to the caller over D-Bus.

Signed-hostap: mukesh agrawal <quiche@chromium.org>
2014-04-13 23:43:04 +03:00
Jouni Malinen
142817b2f9 Add a wpa_supplicant ctrl_iface event for regdom changes
CTRL-EVENT-REGDOM-CHANGE event provides an external notification of
regulatory domain (and any driver channel list) changes.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-13 16:32:38 +03:00
Jouni Malinen
150fd0b2b5 WPS: Split eapol_cb reconnect to a separate code path
Use eloop timeout to run the reconnect command after eapol_cb has
returned. This reduces stack use and can simplify the driver
command/event sequence by allowing the disconnection events from the
provisioning step to be processed before starting the actual data
connection.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-13 11:47:03 +03:00
Jouni Malinen
ded4f944df WPS: Close p2p_group and temporary parameters to all network blocks
If a P2P GO issues multiple credentials for some reason, clone the
p2p_group and temporary parameters to all those based on the initial
network block that gets used for the first credential.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-13 11:44:57 +03:00
Jouni Malinen
e74dd0e55b Add forgotten ampdu_factor into wpa_supplicant.conf
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-13 10:26:53 +03:00
Jouni Malinen
759ff2f075 Re-enable use of wildcard SSID with passphrase
This used to work, but it looks like the disabled-PSK-network check
ended up rejecting confiurations that configured a wildcard SSID with a
passphrase (instead of PSK).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-13 10:26:53 +03:00
Jouni Malinen
023b466da4 Fix a debug print to have a space between words
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-13 10:26:52 +03:00
Jouni Malinen
0cd860284c Add CTRL-EVENT-SIGNAL-CHANGE for bgscan signal update events
This allows external programs to monitor driver signal change events
through wpa_supplicant when bgscan is used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-13 10:26:52 +03:00
Jouni Malinen
bd8838a387 Fix ctrl_iface BLACKLIST return value
Adding a new entry was returning FAIL on success due to incorrect
assumption of wpa_blacklist_add() returning 0 on success (it returns the
positive blacklist count).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-13 10:26:51 +03:00
Andres Morales
f3ff948753 P2P: Add NFC_HANDOVER commands to p2p_redir list
These commands can be executed on the P2P interface thus should be
redirected to it when issued to the global control interface.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-04-11 19:22:00 +03:00
Fionn Cleary
481e66b1f8 Fix reassociate dbus method
- Reassociate was only working when there was already a connect in
  place, which is not how the REASSOCIATE command from the ctrl
  interface works.

Signed-off-by: Fionn Cleary <fionn.cleary@streamunlimited.com>
2014-04-11 19:22:00 +03:00
Daichi Ueura
2150c33337 wpa_cli: Fix wrong comparison in wpa_cli_cmd_interface
Signed-off-by: Daichi Ueura <daichi.ueura@gmail.com>
2014-04-11 19:22:00 +03:00
Sunil Dutt
8235f89f3f P2P: Mark the scan in p2p_in_invitation as p2p_probe
Mark the scan performed by the P2P Client in search of the GO
during the persistant reinvocation as a p2p_probe to avoid
unnecessary use of 802.11b rates.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-10 19:54:36 +03:00
Amarnath Hullur Subramanyam
38ce8e2709 Android: Add qca-vendor.h to be exported
Add qca-vendor.h along with wpa_ctrl.h to be exported to
common staged location.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-10 16:34:23 +03:00
Jouni Malinen
897a5ccee8 WNM: Remove unnecessary present flag
The structures are all allocated, so the pointer can be compared to NULL
to determine whether the subelement was present.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-08 01:34:17 +03:00
Jouni Malinen
f6ce70dc0d WNM: Fix neighbor report subelement formats
Number of of subelements were using incorrect format definition.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-08 01:32:28 +03:00
Jouni Malinen
e9cb7b9275 WNM: Fix neighbor report subelement parser to not leak memory
If a subelement is unexpectedly included multiple times, the parser must
not re-allocate memory for the entry without first freeing the old
allocation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-08 01:20:24 +03:00
Jouni Malinen
1aa6f953bb WNM: Fix neighbor report subelement parser
Only the Neighbor Report element should be included here, so verify that
the element id matches. In addition, verify that each subelement has
valid length before using the data.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-08 01:01:55 +03:00
Jouni Malinen
f8b10c1770 Fix CONFIG_AP=y build without CONFIG_P2P=y
Commit ca9bc5b566 used P2P functionality
from ap.c without proper ifdef CONFIG_P2P.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-07 13:40:58 +03:00
Jouni Malinen
f05cee9714 P2P: Clear p2p_in_invitation on cancel
Commit 41d5ce9e0b added scan optimizations
for P2P invitation cases. However, it left a path where the invitation
state was not cleared and as such, introduced potential issues for
following scans that ended up getting incorrectly optimized for a single
channel regardless of parameters. Fix this by clearing p2p_in_invitation
more carefully, especially on p2p_cancel command.

p2p_cancel is now also run from the FLUSH command to avoid issues with
hwsim test cases (e.g., persistent_group_per_sta_psk followed by
ap_open_tdls resulted in an error due to p2p_in_invitation remaining set
after FLUSH).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-07 13:40:58 +03:00
Jouni Malinen
ec331d09a2 WNM: Fix deinit path to clean neighbor report count
wnm_deallocate_memory() left wnm_num_neighbor_report set while freeing
the allocated buffer of neighbor reports. If this function was called
twice in a row without having went through new neighbor report parsing,
invalid pointers could have been freed resulted in segfault.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-07 13:40:45 +03:00
Jouni Malinen
679f2e7c5f WPS NFC: Remove NFC_RX_HANDOVER_SEL
The newer NFC_REPORT_HANDOVER command is more general version that
handles the cases where NFC_RX_HANDOVER_SEL could potentially have been
used. In addition, with the new WPS NFC design, it is important to
receive the handover request message that was used in the handover in
addition to the select message, so the NFC_RX_HANDOVER_SEL command on
its own would not be sufficient for this.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-07 00:56:04 +03:00
Jouni Malinen
dc39004318 WPS: Remove unused WEP related functionality
Now that WPS 2.0 support is enabled unconditionally, WEP and Shared auth
type are not allowed. This made some of the older code unused and that
can now be removed to clean up the implementation. There is still one
place where WEP is allowed for testing purposes: wpa_supplicant as
Registrar trying to configure an AP to use WEP. That is now only allowed
in CONFIG_TESTING_OPTIONS=y builds, though.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-06 12:31:45 +03:00
Jouni Malinen
9ff4de6de4 Move DROP_SA command to be within ifdef CONFIG_TESTING_OPTIONS
This is a test command and has no use in production builds.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-05 23:59:31 +03:00
Jouni Malinen
9a147ba18d WNM: Fix regression in Sleep Mode exit key data parsing
Commit dbfb8e82ff changed the Action frame
RX payload pointer design to point to a different field. WNM Sleep Mode
Response handler updated one of the uses to accommodate this change, but
that commit missed another use for key data length. This resulted in GTK
and IGTK being ignored in many cases when waking up from WNM Sleep Mode
with PMF enabled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-05 20:42:13 +03:00
Dmitry Shmidt
204c9ac4ee Extend select_network command with freq= to reduce scan time
This allows a subset of channels to be specified for the scan used to
find the network when the SELECT_NETWORK ctrl_iface command is issued.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-04-04 23:07:17 +03:00
Jouni Malinen
75aea3e704 Interworking: Add writing of forgotten cred parameters into config file
req_conn_capab and required_roaming_consortium parameters were not
written into the cred block when requesting wpa_supplicant to write the
configuration file.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-04 22:57:15 +03:00
Jouni Malinen
c880ab87ee Interworking: Add GET_CRED ctrl_iface command
"GET_CRED <id> <field>" can now be used to fetch credential parameters
over the control interface. This does not allow passwords etc. private
material to be retrieved ("*" is returned for those if the value is set
regardless of the value). FAIL is returned if the requested parameter
has not been set. For cred parameters that can have multiple values,
newline separated list of values is returned.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-04 20:13:53 +03:00
Jouni Malinen
1619e9d512 Interworking: Add ctrl_iface events on cred block modifications
Following events are now sent to ctrl_iface monitors to indicate if
credential blocks have been added, modified, or removed:

CRED-ADDED <id>
CRED-MODIFIED <id> <field>
CRED-REMOVE <id>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-04 19:10:47 +03:00
Pawel Kulakowski
39a5800f7c wpa_supplicant: Allow disabling LDPC
Allows user to disable LDPC coding.
This possibility is useful for testing purpose.

Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
2014-04-01 11:20:48 +03:00
Jean Trivelly
72300408d4 Interworking: Read IMSI if not read at supplicant start
It is required to read IMSI from SIM if it has not already been done
when comparing HS 2.0 AP 3GPP information with the local credentials.

Signed-off-by: Jean Trivelly <jean.trivelly@intel.com>
2014-03-31 23:44:59 +03:00
Jean Trivelly
62f736dd04 Interworking: Init scard when a credential requires SIM access
When an ANQP fetch is triggered and ANQP_3GPP_CELLULAR_NETWORK info is
required, initialize scard to be ready when comparing ANQP and
credentials.

Signed-off-by: Jean Trivelly <jean.trivelly@intel.com>
2014-03-31 23:35:08 +03:00
Jean Trivelly
729897a388 Interworking: Fix incorrect compile PCSC flag
CONFIG_PCSC is used instead of PCSC_FUNCS.

Signed-off-by: Jean Trivelly <jean.trivelly@intel.com>
2014-03-31 23:29:37 +03:00
Avraham Stern
ace0fbdb69 P2P: Fix segfault when PBC overlap is detected
If a separate P2P group interface is used, PBC overlap during group
formation causes the group interface to be removed, which ends up with
the interface context becoming invalid. Fix this by scheduling a timeout
to process the PBC overlap and interface removal instead of removing the
interface directly before the connection operation has returned.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2014-03-28 19:31:26 +02:00
Jouni Malinen
cf15b15cc1 Add writing of network block ocsp parameter
This was forgotten from the per-network ocsp parameter addition. The new
parameter needs to be stored to the configuration file similarly to the
other EAP parameters.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-28 16:56:41 +02:00
Ilan Peer
f1c4dbf5cd wpa_supplicant: Remove pending sme-connect radio work
If a new connection is attempted while there is a pending sme-connection
radio work, cancel the pending radio work and continue with the new
connection attempt. This is preferable over rejecting the new work and
continuing with the pending one, as it is possible that the previous
work is no longer valid.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-03-27 16:45:25 +02:00
Eliad Peller
4f560cdee3 wpa_supplicant: Override HT A-MPDU size if VHT A-MPDU was overridden
According to the standard, if the max A-MPDU VHT cap is <= 3, we
have to adjust the max A-MPDU HT cap to the same value. Otherwise
it should be set to 3.

Take care of it when the max VHT A-MPDU value is overridden.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2014-03-27 16:45:21 +02:00
Ilan Peer
782e2f785e P2P: Do not initiate scan on P2P Device when enabled
Do not start a scan on a P2P Device interface when processing an
interface enabled event.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-03-27 15:25:12 +02:00
Sunil Dutt
96ecea5eb1 Pass TDLS peer capability information in tdls_mgmt
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct the
VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the presence
of the respective IEs in the received TDLS Setup Response frame.

The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-27 15:18:48 +02:00
Dmitry Shmidt
cf28c66bcb HS 2.0: Extend ANQP_GET to accept Hotspot 2.0 subtypes
This allows a single ANQP query to be used to fetch both IEEE 802.11
defined ANQP elements and Hotspot 2.0 vendor specific elements.

ANQP_GET <addr> <info id>[,<info id>]...
[,hs20:<subtype>][...,hs20:<subtype>]

For example:
ANQP_GET 00:11:22:33:44:55:66 258,268,hs20:3,hs20:4

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-03-25 18:33:21 +02:00
Jouni Malinen
163f801ef2 nl80211: Indicate HS 2.0 OSEN AKM in connect/associate command
This allows drivers that build the WPA/RSN IEs internally to use similar
design for building the OSEN IE.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-25 18:33:21 +02:00
Jouni Malinen
c201f93a9e WPS: Enable WSC 2.0 support unconditionally
There is not much point in building devices with WPS 1.0 only supported
nowadays. As such, there is not sufficient justification for maintaining
extra complexity for the CONFIG_WPS2 build option either. Remove this by
enabling WSC 2.0 support unconditionally.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-25 18:33:21 +02:00
Sunil Dutt Undekari
91364b7f10 P2P: Set a timeout for a persistent reinvoke on a P2P Client
Use P2P group formation timeout to wait for the 4-way handshake to
complete on a persistent reinvocation on a P2P Client.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-25 15:38:33 +02:00
Rashmi Ramanna
41d5ce9e0b P2P: Optimize scan for GO during persistent group invocation
Scan for GO on the negotiated operating channel for few iterations
before searching on all the supported channels during persistent group
reinvocation. In addition, use the already known SSID of the group in
the scans. These optimizations reduce group formation time.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-25 15:38:33 +02:00
Jouni Malinen
31ded52e70 SME: Add more debug prints for OBSS scans and 20/40 MHz co-ex report
This makes it easier to debug wpa_supplicant behavior when reporting
20/40 MHz co-ex information based on OBSS scans.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-23 23:56:50 +02:00
Jouni Malinen
7f8eb34dee SME: Fix OBSS scan result processing for 20/40 MHz co-ex report
The 40 MHz intolerant bit needs to be checked before skipping the BSS
based on the channel already being in the lost (which could have
happened due to another BSS that does not indicate 40 MHz intolerant).
This fixed the 20/40 MHz co-ex report to indicate 20 MHz request
properly if there are both 40 MHz tolerant and intolerant BSSes on the
same channel.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-23 23:54:50 +02:00
Dmitry Shmidt
d3c9c35f32 Add freq= parameter to 'set pno' command
This allows channels-to-be-scanned to be specified for PNO similarly to
the scan command.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-03-21 23:56:46 +02:00
Tomasz Bursztyka
b998236543 dbus: Implement P2P Peers info IEs buffer getter
Since it declares providing such property, let's expose it relevantly.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-03-21 23:49:47 +02:00
Tomasz Bursztyka
c6f356f85b dbus: Export the peer's device address as a property
This could be useful in some cases.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-03-21 23:44:09 +02:00
Tomasz Bursztyka
442adfde3d dbus: Declare properly ServiceDiscoveryRequest method
It does return something: the reference of the request, as an integer,
which can be used then with ServiceDiscoveryCancelRequest to get
canceled.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-03-21 23:36:50 +02:00
Tomasz Bursztyka
890374118f dbus: Cancelling a service request always reply by an error
p2p_sd_cancel_request returns -1 in case of error, so does
wpas_p2p_sd_cancel_request.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-03-21 23:36:49 +02:00
Tomasz Bursztyka
13494c4478 dbus: Remove duplicate signal declaration
ServiceDiscoveryExternal is uselessly declared twice.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-03-21 23:36:49 +02:00
Eduardo Abinader
5eae87a7d6 P2P: Fix GO failed interface init
Whenever an ongoing GO Neg has failed, due to interface init, the P2P
Device should cancel timeouts and issue wpas_p2p_group_formation_failed,
so the other peer detects faster group formation has failed.

Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
2014-03-21 23:26:16 +02:00
Andrei Otcheretianski
c46235aaf0 wpa_supplicant: Fix radio_remove_interface
Remove pending radio works when an interface is removed from a radio.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-03-21 22:21:37 +02:00
Dmitry Shmidt
2ce7e4fd74 Android: Enable CONFIG_EAP_AKA_PRIME option
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-03-21 22:21:26 +02:00
Prameela Rani Garnepudi
95bf699f76 Add get_radio_name() driver wrapper for wpa_supplicant
Signed-off-by: Prameela Rani Garnepudi <prameela.g@samsung.com>
2014-03-21 22:20:38 +02:00
Guoqiang Liu
d06ecab344 D-Bus: Make p2p_no_group_iface configurable
Some old device need to set p2p_no_group_iface=1 to set up a P2P
connection, so add a D-Bus interface to configure it.

Signed-off-by: Guoqiang Liu <guoqiang.liu@archermind.com>
2014-03-21 22:17:57 +02:00
Jouni Malinen
1120e45232 Allow config blobs to be set through ctrl_iface
"SET blob <name> <hexdump>" can now be used to set a configuration blob
through the wpa_supplicant control interface.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-15 23:51:37 +02:00
Jouni Malinen
6829da39e6 Fix external radio_work deinit path
The radio_work type was stored within the dynamically allocated
wpa_radio_work buffer and that buffer ended up getting freed before the
final use of the type string within radio_work_done(). This resulted in
freed memory being used for a debug print. Avoid this by freeing the
wpa_external_work instance after having completed radio_work_done() for
the related work.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-14 21:58:46 +02:00
Jouni Malinen
8dd9f9cdde Allow management group cipher to be configured
This allows hostapd to set a different management group cipher than the
previously hardcoded default BIP (AES-128-CMAC). The new configuration
file parameter group_mgmt_cipher can be set to BIP-GMAC-128,
BIP-GMAC-256, or BIP-CMAC-256 to select one of the ciphers defined in
IEEE Std 802.11ac-2013.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-14 21:58:45 +02:00
Manish Bansal
67d39cfb32 P2P: Do not create another group interface on NFC Token enable
If a group interface is present and the command was issued on the group
interface, enable the token for that interface instead of creating a new
one.

Signed-off-by: Manish <manish.bansal@broadcom.com>
2014-03-14 21:58:45 +02:00
Paul Stewart
6aa1cd4e06 wpa_supplicant: Apply VHT_OVERRIDES to wpas_start_assoc_cb()
A previous patch "Support VHT capability overrides" missed one
place where HT overrides were being applied and where it would
also be useful to apply VHT overrides.

Signed-hostap: Paul Stewart <pstew@chromium.org>
2014-03-14 21:50:58 +02:00
Dmitry Shmidt
6e9375e4e1 TDLS: Add get_capability tdls command
Command returns info in format: UNSUPPORTED/INTERNAL/EXTERNAL

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-03-14 21:40:57 +02:00
Jouni Malinen
9a1a538fa5 wpa_supplicant AP: Allow PMF to be enabled with ieee80211w
The ieee80211w parameter was not previously copied to the hostapd BSS
structure from wpa_supplicant configuration, so PMF was practically
disabled. Allow it to be configured through the wpa_supplicant network
configuration block.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-13 18:22:25 +02:00
Jouni Malinen
daa70bdf68 Fix CONFIG_NO_SCAN_PROCESSING=y build
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 22:39:11 +02:00
Peter Qiu
0f44ec8eba Add a reattach command for fast reassociate-back-to-same-BSS
Add "reattach" command to perform single-channel single-ssid scan
instead of full scan when trying to reconnect to the currently
"connected" network (assuming old scan results are not current enough to
skip the scan completely). This allows the scan result to come back in
much faster time. In ath9k, the scan took around 12 seconds with full
background scan, and only 0.1 second with the single-channel single-ssid
scan. Thus, take much less time for the client to re-establish
connection with the currently "connected" network.

Signed-hostap: Peter Qiu <zqiu@chromium.org>
2014-03-11 19:38:01 +02:00
Ben Greear
5d0d72a3e5 wpa_supplicant: Put upper bound on initial scan time delay
This makes stations associate much faster when using lots of stations.
In addition, this avoids delaying the initial scan continuously for
dynamic interface removal/addition cases.

Signed-hostap: Ben Greear <greearb@candelatech.com>
2014-03-11 19:23:17 +02:00
Alexander Bondar
5e3ddf4d23 PNO: Change sched_scan_stopped event to handle pending PNO properly
When a sched_scan_stopped event is received and there is a pending PNO,
it used regular scheduled scan parameters instead of PNO specific
parameters. Change it by calling wpas_start_pno().

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-03-11 19:15:48 +02:00
Alexander Bondar
737e7a08b0 PNO: Move and rename pno_start()/pno_stop()
Move pno_start() and pno_stop() to scan.c as a more relevant location
and rename them to wpas_start_pno()/wpas_stop_pno().

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-03-11 19:12:57 +02:00
Jouni Malinen
09eef142ea Use internal FIPS 186-2 PRF if needed
Previously, EAP-SIM/AKA/AKA' did not work with number of crypto
libraries (GnuTLS, CryptoAPI, NSS) since the required FIPS 186-2 PRF
function was not implemented. This resulted in somewhat confusing error
messages since the placeholder functions were silently returning an
error. Fix this by using the internal implementation of FIP 186-2 PRF
(including internal SHA-1 implementation) with crypto libraries that do
not implement this in case EAP-SIM/AKA/AKA' is included in the build.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-11 16:44:22 +02:00
Jouni Malinen
60b893dfb3 wpa_supplicant: Allow external management frame processing for testing
This enables more convenient protocol testing of AP and P2P
functionality in various error cases and unexpected sequences without
having to implement each test scenario within wpa_supplicant.
ext_mgmt_frame_handle parameter can be set to 1 to move all management
frame processing into an external program through control interface
events (MGMT-RX and MGMT-TX-STATUS) and command (MGMT_TX). This is
similar to the test interface that was added to hostapd previously, but
allows more control on offchannel operations and more direct integration
with the internal P2P module.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-08 20:21:21 +02:00
Ilan Peer
c16a7590cf wpa_supplicant: Add a configuration file for the P2P_DEVICE parameters
Add an option to specify a configuration file that can be used to hold
the P2P_DEVICE configuration parameters. If this option is not used, the
P2P_DEVICE configuration parameters will be read from interface
configuration file.

Note that it is advised to use this option in some cases such as:

If a P2P_DEVICE is supported by the driver, the wpa_supplicant creates a
dedicated P2P Device interface, where the configuration file used for
the main interface is used. As a consequence, if the configuration file
includes network definition etc., the wpa_supplicant will try to perform
station specific flows on the P2P Device interface which will fail.

If a P2P_DEVICE is supported by the driver and update_config is used,
the P2P Device configuration data will override the main interface
configuration data.

Signed-hostap: Ilan Peer <ilan.peer@intel.com>
2014-03-07 00:11:04 +02:00
Jouni Malinen
8f05577d11 Configure beacon interval for IBSS command
wpa_supplicant already allowed beacon interval to be configured for AP
mode operations, but this was not passed to the driver for IBSS even
though the same parameter can used for that case. Add this for the
nl80211 driver interface to allow beacon interval to be controlled for
IBSS as well.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-06 23:09:20 +02:00