Commit graph

103 commits

Author SHA1 Message Date
Jouni Malinen
b89883a444 P2P: Notify WPS-M2D event on parent interface and handle PBC overlap
GO may use M2D to notify that PBC overlap was detected if the GO was
configured to allow only a specific P2P Device to connect using PBC.
We need to report the M2D message on the parent interface if a
separate group interface is used. In addition, we can stop the P2P
operation if PBC overlap was indicated similarly to what we are
already doing in th case the overlap is detected locally.
2011-02-22 12:20:16 +02:00
Ben Greear
4c9695be8f WPS ER: Stop eloop only on the last terminate_cb
This allows all WPS ER instances to be cleaned up properly if more
than one interface has an active WPS ER when wpa_supplicant is being
killed.
2011-02-21 21:47:46 +02:00
Johannes Berg
d1c8ac88b9 DBus: Publish provisioned keys in network properties
When the network was provisioned, we need to get the keys to be able to
reconnect without new provisioning. To be able to publish those keys but
not normally configured ones, add a new attribute to struct wpa_ssid
indicating whether or not keys may be exported.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-02 17:00:12 +02:00
Chao-Wen Yang
449adbaca9 WPS: Indicate WPS-FAIL event on EAPOL timeout-based failure callback
If the EAPOL processing times out (e.g., if the AP stops replying
to messages for some reason) during WPS negotiation, we need to
indicate WPS-FAIL event from eapol_cb since no other WPS failure is
reported for this particular case.
2011-01-13 18:04:33 +02:00
Chao-Wen Yang
c5cf0a18f1 WPS: Add mechanism for indicating non-standard WPS errors
Previously, only the Configuration Error values were indicated in
WPS-FAIL events. Since those values are defined in the specification
it is not feasible to extend them for indicating other errors. Add
a new error indication value that is internal to wpa_supplicant and
hostapd to allow other errors to be indicated.

Use the new mechanism to indicate if negotiation fails because of
WEP or TKIP-only configurations being disallows by WPS 2.0.
2011-01-13 17:50:59 +02:00
Jouni Malinen
6c6ad81f9c WPS: Make WPS-AP-AVAILABLE* events a bit more consistent
The BSS table entries may be in more or less random order and it is
better to show the most likely WPS configuration method in a way that is
somewhat more consistent instead of just showing the method of the first
BSS entry found in the table.
2011-01-05 11:49:03 +02:00
Jouni Malinen
f981eabcf0 WPS: Add option to disable open networks by default
CONFIG_WPS_REG_DISABLE_OPEN=y can be used to configure wpa_supplicant
to disable open networks by default when wps_reg command is used to
learn the current AP settings. When this is enabled, there will be a
WPS-OPEN-NETWORK ctrl_iface event and the user will need to explicitly
enable the network (e.g., with "select_network <id>") to connect to
the open network.
2010-12-30 12:28:13 +02:00
Jouni Malinen
70d84f11fe WPS: Add wps_ap_pin ctrl_iface command for wpa_supplicant AP mode
This can be used to control the AP PIN in wpa_supplicant AP mode
in the same way as the identical command in hostapd ctrl_iface.
2010-11-17 16:46:55 +02:00
Jouni Malinen
3e7533b399 WPS ER: Show SetSelectedRegistrar events as ctrl_iface events
This makes it easier to figure out if something goes wrong in
preparing the AP for enrolling a station.
2010-10-25 21:29:22 +03:00
Jouni Malinen
ef10f4733f WPS ER: Add wps_er_set_config to use local configuration
This command can be used to enroll a network based on a local
network configuration block instead of having to (re-)learn the
current AP settings with wps_er_learn.
2010-10-20 13:37:01 +03:00
Jouni Malinen
092acb5441 WPS: Add virtual flags in Config Methods for WPS 2.0 if needed
This is a workaround for incorrect configuration (missing
virtual/physical identifier for config methods) for WPS 2.0 to
allow unmodified configuration from WPS 1.0 to be used while
enforcing compliant WPS 2.0 values.
2010-10-16 12:57:47 +03:00
Jouni Malinen
545cc6af25 P2P: Send WPS-FAIL event to parent interface, too
This makes it easier to figure out what went wrong during group
formation when per-group interfaces are used.
2010-10-14 20:52:31 +03:00
Jouni Malinen
81611b95ff WPS: Add Config Error into WPS-FAIL events
This makes it easier to figure out what could have failed in the
WPS protocol and potentially provide more information for the
user on how to resolve the issue.
2010-10-14 20:49:54 +03:00
Jouni Malinen
d9c8a7c44c Fix build with CONFIG_WPS_OOB 2010-10-06 16:40:20 +03:00
Jouni Malinen
9647120b07 WPS: Add more verbose debug info on PBC session overlap detection 2010-09-20 15:08:52 -07:00
Jouni Malinen
ff28ccafd5 WPS: Add BSSID to strict validation error messages
This makes it easier to figure out which AP is sending invalid
Beacon or Probe Response frames.
2010-09-20 14:54:22 -07:00
Ardong Chen
2f9929ffcc WPS: Allow pending WPS operation to be cancelled
A new ctrl_interface command, WPS_CANCEL, can now be used to cancel
a pending or ongoing WPS operation. For now, this is only available
with wpa_supplicant (either in station or AP mode). Similar
functionality should be added for hostapd, too.
2010-09-10 10:30:25 -07:00
Ardong Chen
014732ea81 WPS: Fix timeout event to be sent over ctrl_interface
This was supposed to be sent to external event monitors, i.e., to
use wpa_msg instead of wpa_printf.
2010-09-10 10:30:25 -07:00
Jouni Malinen
812bf56ab1 Fix build without CONFIG_P2P=y 2010-09-09 07:20:28 -07:00
Jouni Malinen
e9a7ae41fa P2P: Use SSID from GO Negotiation to limit WPS provisioning step
In order to avoid picking incorrect SSID from old scan results, use
SSID from GO Negotiation to select the AP.
2010-09-09 07:17:23 -07:00
Jouni Malinen
1c9cb49fe9 Trigger WPS configuration update on string changes
Previously, only Device Name string was handled, but similar trigger
is needed on Manufacturer, Model Name, Model Number, and Serial Number
changes.
2010-09-09 07:17:21 -07:00
Jouni Malinen
dcf788d1a4 WPS: Fix configuration strings on config reload
Previously, freed memory could be used as device name (and other similar
parameters) when building WPS IE after SIGHUP.
2010-09-09 07:17:20 -07:00
Jouni Malinen
3c5126a41f P2P: Set Device Password ID in WPS M1/M2 per new rules
If the P2P client (WPS Enrollee) uses a PIN from the GO (Registrar),
Device Password ID in M1 & M2 is set to Registrar-specified.
2010-09-09 07:17:19 -07:00
Jouni Malinen
b22128efdc P2P: Add initial version of P2P Module 2010-09-09 07:17:17 -07:00
Jouni Malinen
2ff99b3c38 P2P: Do not save temporary networks 2010-09-09 07:17:16 -07:00
Jouni Malinen
b2c5a4a3df P2P: Do not filter BSSes based on SSID during P2P Provisioning
TODO: Use group id from GO Neg instead(?)
2010-09-09 07:17:16 -07:00
Jouni Malinen
9fa243b295 P2P: Let WPS code know if it is used in a P2P group 2010-09-09 07:17:16 -07:00
Jouni Malinen
611aea7d41 Allow ctrl_iface SET command to change global config parameters 2010-09-09 07:17:16 -07:00
Jouni Malinen
42f50264c0 WPS: Make fragment size configurable for EAP-WSC peer
"wpa_cli set wps_fragment_size <val>" can now be used to configure the
fragment size limit for EAP-WSC.
2010-09-09 06:07:49 -07:00
Jouni Malinen
ad4741183f WPS 2.0: Make sure PHY/VIRT flag gets set for PBC 2010-09-09 06:07:48 -07:00
Jouni Malinen
54f489be45 WPS 2.0: Validate WPS attributes in management frames and WSC messages
If CONFIG_WPS_STRICT is set, validate WPS IE(s) in management frames and
reject the frames if any of the mandatory attributes is missing or if an
included attribute uses an invalid value. In addition, verify that all
mandatory attributes are included and have valid values in the WSC
messages.
2010-09-09 06:07:48 -07:00
Jouni Malinen
31fcea931d WPS 2.0: Add support for AuthorizedMACs attribute
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
2010-09-09 06:07:47 -07:00
Jouni Malinen
979b988ed6 WPS: Do not allow Label and Display config methods to be enabled
It is unclear which PIN is used if both Label and Display config
methods are advertised. Avoid this by not allowing such configuration.
2010-07-17 20:30:49 -07:00
Jouni Malinen
41e650ae5c WPS: Use different scan result sorting rules when doing WPS provisioning
The AP configuration may change after provisioning, so it is better
not to use the current security policy to prioritize results. Instead,
use WPS Selected Registrar attribute as the main sorting key and use
signal strength next without considering security policy or rate sets.
The non-WPS provisioning case remains as-is, i.e., this change applies
only when trying to find an AP for WPS provisioning.
2010-06-11 13:50:13 -07:00
Jouni Malinen
7d6640a62c WPS ER: Add command for configuring an AP
wps_er_config can now be used to configure an AP. It is similar to
wps_er_learn, but instead of only learning the current AP settings,
it continues to send M8 with the new settings for the AP.
2010-05-28 00:01:48 +03:00
Jouni Malinen
15dbf1291a WPS ER: Add ctrl_iface event for learned AP settings 2010-05-27 15:24:45 +03:00
Jouni Malinen
0848668513 WPS ER: Allow AP filtering based on IP address
wps_er_start command now takes an optional parameter that can be used
to configure a filter to only allow UPnP SSDP messages from the
specified IP address. In practice, this limits the WPS ER operations
to a single AP and filters out all other devices in the network.
2010-05-27 15:23:55 +03:00
Jouni Malinen
17a4734dc4 Optimize post-WPS scan based on channel used during provisioning
Scan only the frequency that was used during provisioning during the
first five scans for the connection. This speeds up connection in the
most likely case where the AP remains on the same channel. If the AP is
not found after these initial scans, all channels will be scanned.
2010-04-11 19:06:42 +03:00
Jouni Malinen
9ba9fa07cc Move wpa_supplicant specific scan code away from src/drivers
This fits better in wpa_supplicant/scan.c. Couple of remaining
scan_helpers.c functions are currently used in driver wrappers,
but they can likely be removed in the future.
2010-01-03 18:48:11 +02:00
Jouni Malinen
6fa81a3b3f Use BSS table entry instead of raw scan result for connection 2010-01-02 16:16:02 +02:00
Jouni Malinen
59f2caa925 WPS: Use BSS table instead of raw scan results 2010-01-02 13:36:12 +02:00
Jouni Malinen
f7e5436502 WPS: Clear SSID selection if more than one BSSID match is found
Need to use wildcard SSID matching for WPS connection if the same
BSSID occurs multiple time in scan results since any of the SSIDs
may be used.
2009-12-28 16:07:15 +02:00
Jouni Malinen
332d630a44 Use wpa_msg_ctrl() for WPS AP available events
No need to include these MSG_INFO level events in stdout/syslog,
so deliver them only to ctrl_iface monitors.
2009-12-28 00:44:10 +02:00
Jouni Malinen
c0e4dd9eeb WPS: Make Config Methods configurable for wpa_supplicant
This adds config_methods configuration option for wpa_supplicant
following the design used in hostapd. In addition, the string is
now parsed in common code from src/wps/wps_common.c and the list
of configurable methods include all the defined methods from
WPS 1.0h spec.
2009-12-21 15:59:25 +02:00
Jouni Malinen
1a1bf008cb WPS ER: Delay wpa_supplicant termination to allow unsubscription
Instead of forcefully deinitializing ER immediately, give it some
time to complete unsubscription and call eloop_terminate() only once
ER code has completed its work.
2009-12-19 23:47:54 +02:00
Jouni Malinen
c1a853438f WPS: Add display and keypad config methods for WPS ER 2009-12-12 16:49:33 +02:00
Jouni Malinen
03da66bd59 Remove src/crypto from default include path
In addition, start ordering header file includes to be in more
consistent order: system header files, src/utils, src/*, same
directory as the *.c file.
2009-11-29 23:04:43 +02:00
Jouni Malinen
3acb50056c Remove src/rsn_supp from default header path 2009-11-29 18:28:08 +02:00
Jouni Malinen
90973fb2fd Remove src/common from default header file path
This makes it clearer which files are including header from src/common.
Some of these cases should probably be cleaned up in the future not to
do that.

In addition, src/common/nl80211_copy.h and wireless_copy.h were moved
into src/drivers since they are only used by driver wrappers and do not
need to live in src/common.
2009-11-29 17:51:55 +02:00
Jouni Malinen
ed45947e9b WPS: Update couple of missed Primary Device Type uses 2009-11-26 11:54:37 +02:00