The five second timeout for GAS queries is excessive and can result in
long waits in cases where APs are either misconfigured or frames are
lost.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the design more robust against unexpected duplicates since
each new GAS exchange gets a different dialog token compared to the
previous one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like it may be possible for an older GAS response to get retransmitted
even after the first copy has been processed. While this should not really come
up all the way to wpa_supplicant due to sequence number being same (i.e.,
duplicate detection should from the frame), some cases have been observed where
this did cause issues. Drop such a frame silently without dropping the ongoing
GAS session to allow a frame with the next frag_id to be processed after this.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This can be useful for some test cases, so allow wpa_supplicant to be
built with special test functionality to expose the current (last
configured) GTK. This is disabled by default and can be enabled by
adding following line into .config:
CFLAGS += -DCONFIG_TESTING_GET_GTK
The GTK can then be fetched with "wpa_cli get gtk".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P management operations like P2P_FIND and P2P_CONNECT are not
really specific to any network interface. These are P2P Device level
operations that are in more global device context. Allow those to be
sent through the global control interface without IFNAME parameter.
For now, these commands are directed within wpa_supplicant to the
network interface that initialized the global P2P context. This may
change in the future if a special context is added for P2P operations.
Anyway, such changes can now be done internally within wpa_supplicant
without affecting this global control interface design from external
view point.
Signed-hostap: Jouni Malinen <j@w1.fi>
These events are sent as a special case to both the group interface and
"parent interface" (i.e., the interface that was used for managing P2P
negotiation). The latter is not really correct event, so get rid of it
with the new global control interface design where there is no need to
support legacy upper layer implementations.
Signed-hostap: Jouni Malinen <j@w1.fi>
This removes the "IFNAME=<ifname> " prefix from P2P events that are
received through the global control interface since these events are not
really specific to any network interface, but the full device.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace direct wpa_msg() calls with p2p_dbg(), p2p_info(), and p2p_err()
calls that use a new debug_print() callback to handle actual debug
printing outside the P2P module.
Signed-hostap: Jouni Malinen <j@w1.fi>
This removes wpa_ctrl.h dependency from src/p2p/* and makes the P2P
events more consistent, i.e., everything that is aimed for upper layer
processing from the wpa_supplicant control interfaces is generated in
p2p_supplicant.c.
Signed-hostap: Jouni Malinen <j@w1.fi>
This function can be used instead of wpa_msg() and wpa_msg_ctrl() to
indicate that an event is not specific to a network interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
The ATTACH/DETACH mechanism to request event messages from
wpa_supplicant can now be used through the global control interface,
too. This results in events from all interfaces being delivered through
a single monitor socket. "IFNAME=<ifname> " prefix is used on events
that are specific to an interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to implement filtering of channels for scan and based
on that, for connection, purposes.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This updates hostapd to build using the new keystore header file
location and adds a note that the old frameworks/base/cmds/keystore can
be removed at some point in the future when old Android releases do not
need to be supported.
Signed-hostap: Jouni Malinen <j@w1.fi>
The wpa_supplicant global control interface parameter can now be used to
explicitly specify an abstract UNIX domain socket (Linux specific
extension) with "@abstract:" prefix and an Android control socket with
"@android:" prefix.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is mostly a corner case at this point, but if wpa_cli was started
with global control interface connection (-g) and interactive mode,
per-interface control interface was tried to be opened with the
previously opened global ctrl_iface connection gettign leaked.
Signed-hostap: Jouni Malinen <j@w1.fi>
The optional -G<group> command line argument can be used to specify the
group that can access the global control interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
"IFNAME=<ifname> " prefix can now be used on the wpa_supplicant global
control interface to direct a command to a specific interface instead of
having to use an interface specific control interface for this. This
allows a single socket to be used for controlling multiple virtual
interfaces.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 21d996f775 added p2p_pref_chan as a
configuration file parameter, but included only the case of dynamically
setting this at runtime through the control interface SET command.
Complete this functionality by taking this value into use directly from
the configuration file, too.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
By default, dbus_connection_dispatch() will call _exit() if the bus
connection has been closed. This caused wpa_supplicant to terminate
without properly cleaning up after itself.
To ensure that we terminate cleanly when the messagebus terminates,
override the exit_on_disconnect behavior and install a filter to handle
libdbus's "Disconnected" signal.
[Bug 474]
Signed-hostap: Daniel Gnoutcheff <daniel@gnoutcheff.name>
The new control interface command can be used to send a
BSS Transition Management Query frame to the current AP.
Signed-hostap: Vinayak Kamath <vkamat@codeaurora.org>
The WPS provisioning case does not result in successful connection by
design and as such, this can result in networks getting temporarily
disabled. Avoid this by clearing the failure counts on WPS success.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of just adding the new network, prefer the network learnt from a
configuration token during the first connection attempt. This makes the
WPS NFC case behave similarly to the in-band provisioning cases if there
are more preferred networks in the scan results.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up debug log by not trying to process the disconnection
event as a failure that could result in blacklist addition and auto
connect attempt. These are pointless operations since the interface is
going to removed immediately after this.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up debug log by not requesting the auto connect on
dissassociation event if we are already in disconnected state and would
not try to connect anyway.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no point in marking a BSS temporarily blacklisted based on a
connection failure or disconnection case if that happens as a result of
a local request to disconnect. The blacklist entry could result on
unexpected BSS getting selected on the next connection attempt. In
addition, the code to try to find another BSS within the ESS could
result in scanning a single channel on the next attempt. Fix these
issues by handling the connection failure events only if we are not in
disconnected state (i.e., would try to reconnect after this
automatically).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Scanning can delay concurrent operations considerably, so it is better
to avoid that while trying to connect on any of the virtual interfaces
that share the same radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a VIF is already associated, then only scan on the associated
frequency if user requests such. This is a big help when using
lots of virtual stations.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
In the systemd interface templated the alias entry was specified
with wlan0 hard coded. Changing it to %i in this patch. [Bug 477]
Reported-by: zg <ml@mail.tsaitgaist.info>
Signed-hostap: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
cfg80211 rejects the set_key operations before the IBSS network has been
fully formed, so add one more attempt to set the key for WPA-None at
IBSS joined driver event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to repeat the driver capability fetch for each
operation since we already cache driver flags in wpa_s->drv_flags.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new sched_scan_interval parameter can be used to set the default
sched_scan interval, e.g., for power saving purposes.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The use of AID=1 for the nl80211 dummy STA case is specific to the
driver (cfg80211), so better move this into the driver wrapper instead
of generic TDLS implementation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's AID is required for the driver to
construct partial AID in VHT PPDU's. Pass this information to the driver
during add/set station operations (well, as soon as the information is
available, i.e., with set station operation currently).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The Hotspot 2.0 specification seems to mandate this element to be
included in all (Re)Association Request frames if the station is Hotspot
2.0 capable. However, that results in conflicts with other requirements
like no TKIP use when this element is present. The design is really
supposed to include the indication element only for Hotspot 2.0
associations regardless of what the current specification implies.
Remove the HS 2.0 Indication element from (Re)Association Request frame
whenever the connection is not for Hotspot 2.0 purposes.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes tab completion work better in cases where wpa_cli is started
after wpa_supplicant has already discovered BSSes.
Signed-hostap: Jouni Malinen <j@w1.fi>
The old help text did not include most of the parameters and as such,
was not really helpful. Replace it with tab completion function that
includes more or less all available parameters.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, interactive mode could not be used to enter space-separated
lists with the set command. This removes that restriction and allows
such commands to be encoded properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows one to limit the channels that wpa_supplicant will
scan. This is a useful addition to the freq_list configurable
in the network {} section.
Signed-hostap: Ben Greear <greearb@candelatech.com>
This updates number of comments in android.config to match the latest
version in defconfig and adds some of the entries that were previously
present only in android.config into defconfig.
Signed-hostap: Jouni Malinen <j@w1.fi>
Each attempt to connect to the same network using WPS would result
in the duplicate configuration getting added. Avoid such redundant
additions by comparing the network configuration with an already
existing one and remove the older network if the new credential
provisioned through WPS is identical.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
nl80211 has obsoleted WEXT as the preferred kernel interface for
controlling wireless drivers. Update wpa_supplicant driver interface
list order so that nl80211 gets used first if both nl80211 and wext
interfaces are included in the build. In addition, update README to
reflect the fact that WEXT is obsolete.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
