wpa_insert_pmkid() did not support cases where the original RSN IE
included any PMKIDs. That case can happen when PTK rekeying through
4-way handshake is used after FT protocol run. Such a 4-way handshake
used to fail with wpa_supplicant being unable to build the EAPOL-Key msg
2/4.
Fix this by extending wpa_insert_pmkid() to support removal of the old
PMKIDs, if needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant control interface command "TEST_ASSOC_IE
<hexdump>" can now be used to override the WPA/RSN IE for Association
Request frame and following 4-way handshake to allow protocol testing of
AP side processing of WPA/RSN IE.
Signed-off-by: Jouni Malinen <j@w1.fi>
Number of places were calling functions that are not included in
CONFIG_NO_WPA=y build anymore. Comment out such calls. In addition, pull
in SHA1 and MD5 for config_internal.c, if needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_sm_key_mgmt_set_pmk() was checking for proactive_key_caching to be
enabled before setting the PMK to the driver. This check is not required
and would mandate configuration setting of okc or proactive_key_caching
for cases which were not necessary.
Signed-off-by: Amarnath Hullur Subramanyam <amarnath@qca.qualcomm.com>
Some APs may send RSC octets in EAPOL-Key message 3 of 4-Way Handshake
or in EAPOL-Key message 1 of Group Key Handshake in the opposite byte
order (or by some other corrupted way). Thus, after a successful
EAPOL-Key exchange the TSC values of received multicast packets, such as
DHCP, don't match the RSC one and as a result these packets are dropped
on replay attack TSC verification. An example of such AP is Sapido
RB-1732.
Work around this by setting RSC octets to 0 on GTK installation if the
AP RSC value is identified as a potentially having the byte order issue.
This may open a short window during which older (but valid)
group-addressed frames could be replayed. However, the local receive
counter will be updated on the first received group-addressed frame and
the workaround is enabled only if the common invalid cases are detected,
so this workaround is acceptable as not decreasing security
significantly. The wpa_rsc_relaxation global configuration property
allows the GTK RSC workaround to be disabled if it's not needed.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Provide information on whether EAPOL-Key frame was sent successfully to
kernel for transmittion. wpa_eapol_key_send() will return
>= 0 on success and < 0 on failure. After receiving EAPOL-Key msg 3/4,
wpa_supplicant sends EAPOL-Key msg 4/4 and shows CTRL-EVENT-CONNECTED
only after verifying that the msg 4/4 was sent to kernel for
transmission successfully.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
There is no point in sending TPK M3 (TDLS Setup Confirm) with a failure
status if the first transmission attempt fails. Instead, just return a
failure by disabling the link rather than retransmitting the TPK M3
frame with an error status.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
On TPK lifetime expiration, tear down the direct link before renewing
the link in the case of TDLS initiator processing. The expired key
cannot be used anymore, so it is better to explicitly tear down the old
link first.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In addition to the PTK length increasing, the length of the PMK was
increased (from 256 to 384 bits) for the 00-0f-ac:12 AKM. This part was
missing from the initial implementation and a fixed length (256-bit) PMK
was used for all AKMs.
Fix this by adding more complete support for variable length PMK and use
384 bits from MSK instead of 256 bits when using this AKM. This is not
backwards compatible with the earlier implementations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 7d711541dc ('Clear TK part of PTK
after driver key configuration') started clearing TK from memory
immediately after having configured it to the driver when processing
EAPOL-Key message 3/4. While this covered the most common case, it did
not take into account the possibility of the authenticator having to
retry EAPOL-Key message 3/4 in case the first EAPOL-Key message 4/4
response is lost. That case ended up trying to reinstall the same TK to
the driver, but the key was not available anymore.
Fix the EAPOL-Key message 3/4 retry case by configuring TK to the driver
only once. There was no need to try to set the same key after each
EAPOL-Key message 3/4 since TK could not change. If actual PTK rekeying
is used, the new TK will be configured once when processing the new
EAPOL-Key message 3/4 for the first time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The GTK value received in RSN (WPA2) group rekeying did not use the
wpa_hexdump_key() version of debug printing that is conditional on -K
being included on the command line.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant_parse_ies() was never supposed to be used as a generic IE
parser, i.e., it is for the specific purpose of parsing EAPOL-Key Key
Data IEs and KDEs. TDLS used this function for parsing generic AP IEs
and while that works, it resulted in confusing "WPA: Unrecognized
EAPOL-Key Key Data IE" debug messages. Clean this up by using
ieee802_11_parse_elems() for the cases where generic IEs are being
parsed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new CONFIG_NO_RC4=y build option can be used to remove all internal
hostapd and wpa_supplicant uses of RC4. It should be noted that external
uses (e.g., within a TLS library) do not get disabled when doing this.
This removes capability of supporting WPA/TKIP, dynamic WEP keys with
IEEE 802.1X, WEP shared key authentication, and MSCHAPv2 password
changes.
Signed-off-by: Jouni Malinen <j@w1.fi>
If WPA2-Enterprise connection with full EAP authentication (i.e., no
PMKSA caching used) results in a PMKID that does not match the one the
AP/Authenticator indicates in EAPOL-Key msg 1/4, there is not much point
in trying to trigger full EAP authentication by sending EAPOL-Start
since this sequence was immediately after such full authentication
attempt.
There are known examples of authentication servers with incorrect MSK
derivation when TLS v1.2 is used (e.g., FreeRADIUS 2.2.6 or 3.0.7 when
built with OpenSSL 1.0.2). Write a clear debug log entry and also send
it to control interface monitors when it looks likely that this case has
been hit. After doing that, stop the connection attempt by
disassociating instead of trying to send out EAPOL-Start to trigger new
EAP authentication round (such another try can be tried with a new
association).
Signed-off-by: Jouni Malinen <j@w1.fi>
The FT-specific check for valid group cipher in wpa_ft_gen_req_ies() was
not up-to-date with the current list of supported ciphers. Fix this by
using a generic function to determine validity of the cipher. In
practice, this adds support for using CCMP-256 and GCMP-256 as the group
cipher with FT.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
All the existing users of these elements were already validating the
element length. However, it is clearer to validate this already at the
parser for extra layer of protection for any future changes.
Signed-off-by: Jouni Malinen <j@w1.fi>
This program can be used to run fuzzing tests for areas related to EAPOL
frame parsing and processing on the supplicant side.
Signed-off-by: Jouni Malinen <j@w1.fi>
Old code defaulted to WEP for an AP advertising OSEN. Show as OSEN
instead. Re-use most of the RSN parsing logic since all but the header
is the same.
Example output:
[root@ath9k-f lanforge]# ./local/bin/wpa_cli -i sta0 scan_results
bssid / frequency / signal level / flags / ssid
00:0e:8e:6f:40:49 2462 -23 [OSEN-OSEN-CCMP][ESS] ben-138
Signed-off-by: Ben Greear <greearb@candelatech.com>
Previously, it would have been possible to complete RSN connection by
skipping the msg 3/4 and 4/4 completely. This would have resulted in
pairwise key not being configured. This is obviously not supposed to
happen in practice and could result in unexpected behavior, so reject
group key message before the initial 4-way handshake has been completed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, it was possible for the wpa_sm_start_preauth() and
wpa_sm_rekey_ptk() eloop callbacks to remain active after disconnection
and potentially continue to be used for the next association. This is
not correct behavior, so explicitly cancel these timeouts to avoid
unexpected attempts to complete RSN preauthentication or to request PTK
to be rekeyed.
It was possible to trigger this issue, e.g., by running the following
hwsim test case sequence: ap_wpa2_ptk_rekey ap_ft_sae_over_ds
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some APs (e.g., Cisco 1260) sometimes add padding to the end of short
TDLS management packets and that can look like invalid IEs. This was
allowed on M3 and discovery packets, but not in others. Allow it for the
other packets as well, since required IEs are verified in the code
anyway.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for wpa_tdls_teardown_peers() to be called with sm ==
NULL in case interface addition fails before the WPA state machine is
initialized.
Signed-off-by: Jouni Malinen <j@w1.fi>
The supplicant code does not try to control the actual channel of the
radio at any point. It simply passes the target peer and channel
parameters to the driver. It's the driver's responsibility to
periodically initiate TDLS channel-switch operations when TDLS
channel-switching is enabled.
Allow enable/disable operations to be invoked via the control interface.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Mark an appropriate sm flag when TDLS switch is prohibited by the AP.
Populate the flag upon association with the AP.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
It was possible for the decrypted EAPOL-Key Key Data field to remain in
heap after the temporary buffer was freed. Explicitly clear that buffer
before freeing it to minimize the time GTK remains in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need for wpa_supplicant to maintain a copy of the TK part of
PTK after this has been configured to the driver, so clear that from
heap memory and only maintain KEK and KCK during association to allow
additional EAPOL-Key handshakes.
Signed-off-by: Jouni Malinen <j@w1.fi>
PMK and PTK are not needed in the supplicant state machine after
disassociation since core wpa_supplicant will reconfigure them for the
next association. As such, clear these from heap in
wpa_sm_notify_disassoc() to reduce time and number of places storing key
material in memory. In addition, clear FT keys in case of
CONFIG_IEEE80211R=y build (sm->xxkey stored a copy of PSK in case of
FT-PSK).
Signed-off-by: Jouni Malinen <j@w1.fi>
This converts os_snprintf() result validation cases to use
os_snprintf_error() for cases that were note covered by spatch and
semantic patches.
Signed-off-by: Jouni Malinen <j@w1.fi>
Bounds checking for gd->gtk_len in wpa_supplicant_check_group_cipher()
was apparently too complex for some static analyzers. Use a local
variable and a more explicit validation step to avoid false report.
(CID 62864)
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support for AKM 00-0F-AC:11 to specify the integrity and
key-wrap algorithms for EAPOL-Key frames using the new design where
descriptor version is set to 0 and algorithms are determined based on
AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new AKM uses a different mechanism of deriving the PMKID based on
KCK instead of PMK. hostapd was already doing this after the KCK had
been derived, but wpa_supplicant functionality needs to be moved from
processing of EAPOL-Key frame 1/4 to 3/4 to have the KCK available.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like some APs are incorrectly selecting descriptor version 3
(AES-128-CMAC) for EAPOL-Key frames when version 2 (HMAC-SHA1) was
expected to be used. This is likely triggered by an attempt to negotiate
PMF with SHA1-based AKM.
Since AES-128-CMAC is considered stronger than HMAC-SHA1, allow the
incorrect, but stronger, option to be used in these cases to avoid
interoperability issues with deployed APs.
This issue shows up with "WPA: CCMP is used, but EAPOL-Key descriptor
version (3) is not 2" in debug log. With the new workaround, this issue
is ignored and "WPA: Interoperability workaround: allow incorrect
(should have been HMAC-SHA1), but stronger (is AES-128-CMAC), descriptor
version to be used" is written to the log.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_supplicant SME create PMKSA cache entries from SAE
authentication and try to use PMKSA caching if an entry is found for the
AP. If the AP rejects the attempt, fall back to SAE authentication is
used.
Signed-off-by: Jouni Malinen <j@w1.fi>
dl_list_del() followed by dl_list_add() seemed to confuse clang static
analyzer somehow, so explicitly check for the prev pointer to be
non-NULL to avoid an incorrect warning.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds kek_len argument to aes_wrap() and aes_unwrap() functions and
allows AES to be initialized with 192 and 256 bit KEK in addition to
the previously supported 128 bit KEK.
The test vectors in test-aes.c are extended to cover all the test
vectors from RFC 3394.
Signed-off-by: Jouni Malinen <j@w1.fi>
Relying on qos qosinfo is not enough, as it can be 0 for WMM enabled
peers that don't support U-APSD. Further, some peers don't even contain
this IE (Google Nexus 5), but do contain the WMM IE during setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
A recent mac80211 patch ("8f02e6b mac80211: make sure TDLS peer STA
exists during setup") forces the TDLS STA to exist before sending any
mgmt packets. Add the STA before sending a concurrent-setup test packet.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Some drivers need to know the initiator of a TDLS connection in order
to generate a correct TDLS mgmt packet. It is used to determine
the link identifier IE. Pass this information to the driver.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
IEEE 802.11 standard sends AID in a field that is defined in a bit
strange way to set two MSBs to ones. That is not the real AID and those
extra bits need to be filtered from the value before passing this to the
driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
TDLS Setup Request frame has to be rejected with status code 37 ("The
request has been declined"), if the BSSID in the received Link
Identifier does not match the current BSSID per IEEE Std 802.11-2012,
10.22.4 ('TDLS direct-link establishment') step (b). The previously used
status code 7 ('Not in same BSS') is described to used only when
processing TPK Handshake Message 2 in TDLS Setup Response frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the earlier commit e6270129f6
('Clean up EAPOL-Key Key Data processing') design to be used with
PeerKey EAPOL-key processing as well. This avoids false warnings from
static analyzer (CID 62860, CID 62861, CID 62862).
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a helper function to avoid multiple copies of the same long list of
argument parameters to wpa_sm_tdls_peer_addset() from the peer entry.
Signed-off-by: Jouni Malinen <j@w1.fi>
Update the peer STA with full info sending TDLS Setup Response/Confirm
frames instead of after the full setup exchange. This makes it easier
for some drivers to properly negotiate QoS and HT information on the
direct link.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
There is no need to keep the peer entry in memory after the link has
been removed.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Tested-by: Ilan Peer <ilan.peer@intel.com>
Some APs (Cisco) may tack on a weird IE to the end of a TDLS Discovery
Request packet. This needn't fail the response, since the required IEs
are verified separately.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Some APs (Cisco) may tack on a weird IE to the end of the TDLS confirm
packet, which can fail negotiation. As an interoperability workaround,
ignore IE parser failures and reject the frame only if any of the
mandatory IEs are not included.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Commit 342bce63cd introduced a possibility
of a NULL pointer dereference on the error path if a new peer entry
fails to get added (i.e., memory allocation failure). Fix that by
skipping the wpa_tdls_peer_free() call if necessary.
Signed-off-by: Jouni Malinen <j@w1.fi>
The driver might not be able to add the TDLS STA. Fail if this happens.
Also fix the error path to always reset the TDLS peer data.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
If a link is unreachable, the specification mandates we should send a
teardown packet via the AP with a specific teardown reason. Force this
by first disabling the link and only then sending the teardown packet
for the LOW_ACK event.
Rename the TDLS LOW_ACK event handler to better reflect its purpose.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Use a single location in wpa_sm_rx_eapol() for preparing the pointer to
the Key Data field and to its validated length instead of fetching that
information in number of processing functions separately.
Signed-off-by: Jouni Malinen <j@w1.fi>
Re-order wpa_sm_rx_eapol() to first go through all EAPOL (802.1X) header
validation steps using the original message buffer and re-allocate and
copy the frame only if this is a valid EAPOL frame that contains an
EAPOL-Key. This makes the implementation easier to understand and saves
unnecessary memory allocations and copying should other types of EAPOL
frames get here.
Signed-off-by: Jouni Malinen <j@w1.fi>
The additional eight octet field was removed from keydatalen without
proper validation of the Key Data Length field. It would have been
possible for an invalid EAPOL-Key frame to be processed in a way that
ends up reading beyond the buffer. In theory, this could have also
resulted in writing beyond the EAPOL-Key frame buffer, but that is
unlikely to be feasible due to the AES key wrap validation step on
arbitrary memory contents.
Signed-off-by: Jouni Malinen <j@w1.fi>
The following kde.rsn_ie_len != peer->rsnie_i_len was already taking
care of enforcing the length to be within the target buffer length.
Anyway, this explicit check makes this clearer and matches the design in
TPK M1 processing.
Signed-off-by: Jouni Malinen <j@w1.fi>
If PMF was enabled, the validation step for EAPOL-Key descriptor version
ended up rejecting the message if GCMP had been negotiated as the
pairwise cipher. Fix this by making the GCMP check skipped similarly to
the CCMP case if a SHA256-based AKM is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Disabling the link only clears the local state. The remote peer will
still think we are connected and disallow the setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
When de-authenticating from the AP, disable each TDLS link after
sending the teardown packet. Postpone the reset of the peer state
data until after the link disable request.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Commit 96ecea5eb1 did not consider
to pass the VHT/HT/WMM capabilities of the peer for BSS with
open mode.
Address this issue by passing the capabilities irrespective of
the security mode.
Signed-off-by: Pradeep Reddy POTTETI <c_ppotte@qti.qualcomm.com>
Some of the buffers used to keep a copy of PTK/TPTK/GTK in the
supplicant implementation maintained a copy of the keys longer than
necessary. Clear these buffers to zero when the key is not needed
anymore to minimize the amount of time key material is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
"SET tdls_testing 0x800" can be used to enable a special test mode that
forces the FTIE MIC in TDLS setup messages to be incorrect.
Signed-off-by: Jouni Malinen <j@w1.fi>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct the
VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the presence
of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd to set a different management group cipher than the
previously hardcoded default BIP (AES-128-CMAC). The new configuration
file parameter group_mgmt_cipher can be set to BIP-GMAC-128,
BIP-GMAC-256, or BIP-CMAC-256 to select one of the ciphers defined in
IEEE Std 802.11ac-2013.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
TDLS Setup Request/Response frames from the peers include the WMM IE,
hence parse the same and consider the QoS Info from the WMM IE. The
qos_info obtained in the WMM IE overwrites the one obtained through
WLAN_EID_QOS attribute.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Incorrect PTK length was used in PMK-to-PTK derivation and the Michael
MIC TX/RX key swapping code was incorrectly executed for these ciphers
on supplicant side.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like some deployed devices may send an invalid supported
operating class element (length = 0) in TDLS Setup messages. With
cfg80211, this results in the NL80211_CMD_SET_STATION command failing
due to an invalid argument (cfg80211 mandates supported operating
classes information to have a length of 2..253 octets).
Work around this interop issue by ignoring the Supported Operating Class
element if it has invalid length.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's supported channel and operating class
is required for the driver to do TDLS off channel operations with a
compatible peer. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some EAP methods can go through a step that is expected to fail and as
such, should not trigger temporary network disabling when processing
EAP-Failure or deauthentication. EAP-WSC for WPS was already handled as
a special case, but similar behavior is needed for EAP-FAST with
unauthenticated provisioning.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was already possible to configure hostapd and wpa_supplicant to use
FT-SAE for the key management, but number of places were missing proper
AKM checks to allow FT to be used with the new AKM.
Signed-hostap: Jouni Malinen <j@w1.fi>
The earlier changes to buffer EAPOL frames when not associated to avoid
race conditions (especially commit
3ab35a6603 but maybe something even before
that) broke PeerKey 4-way handshake. Fix this by using a separate check
before the race condition workaround to process PeerKey 4-way handshake
EAPOL-Key messages differently.
Signed-hostap: Jouni Malinen <j@w1.fi>
PeerKey entries need to be removed on disassociation and this needs to
be done in a way that cancels the possibly pending eloop timeout.
Signed-hostap: Jouni Malinen <j@w1.fi>
This prepares wpa_supplicant for accepting cases where the AP does not
use group addressed frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The eloop already tracks the expiration/lifetime, and the expiration
isn't really used, so remove it. It should otherwise have used monotonic
time, but since it's not actually used, we can remove it instead.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
A reenable of the TDLS link while the host driver is already processing
the same (due to the retransmitted M2/M3 frames) might result in a
failed TDLS setup handshake due to some host driver's implementation.
Thus, issue enable link only when the peer's TDLS status signifies no
prior link (tpk_success=0).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add DBus methods for TDLS operations similar to those available
for the control interface. This includes Discover, Setup, and
Teardown commands. While here, add a method to query the TDLS
link status and add a DBus method for it.
Tested with CONFIG_TDLS enabled, on a TDLS-enabled host and
peer capable of TDLS:
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "peer does not exist"
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSDiscover string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSSetup string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "connected" after TDLS completes
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSTeardown string:<peer-mac-address>
yields no error
dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
/fi/w1/wpa_supplicant1/Interfaces/0 \
fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>
yields: string "peer not connected"
Signed-hostap: Paul Stewart <pstew@chromium.org>
The GTK rekey offload information was sent to the driver immediately
after the 4-way handshake which ended up being before the initial group
key exchange in the case of WPA (v1). This could result in even that
initial GTK handshake being offloaded and wpa_supplicant being left in
WPA_GROUP_HANDSHAKE state. Fix this by postponing the operation to
happen only after the full set of initial EAPOL-Key exchanges have been
completed (i.e., in the existing location for WPA2 and a after the group
key handshake for WPA).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A new TDLS request shall transmit TPK M1 frame with a unique INonce.
Thus a new explicit request would fail an ongoing TDLS negotiation with
the error "TDLS: FTIE SNonce in TPK M3 does not match with FTIE SNonce
used in TPK M1" if the peer happens to receive two M1 frames before an
M3 frame. Check for the ongoing negotiation with the peer and do not
start a new one if we are already in a setup negotiation with the peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to go through the peer list when we already have a
pointer to the specific peer entry.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is called from number of locations and it is more efficient to use
a new helper function instead of wpa_tdls_disable_link() that would do
peer address search from the list of peers.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Making this function be used only for external setup case simplifies the
implementation and makes core wpa_supplicant calls in ctrl_iface.c and
events.c consistent.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no point in updating the RNonce for every obtained TPK M1 frame
(e.g., retransmission due to timeout) with the same INonce (SNonce in
FTIE). Update RNonce only if a TPK M1 is received with a different
INonce (new TDLS session) to avoid issues with two setup exchanges
getting mixed and exchange failing due to mismatching nonces ("TDLS:
FTIE ANonce in TPK M3 does not match with FTIE ANonce used in TPK M2").
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Clear the peer information and disable the created link on a
failed TDLS setup negotiation. This is needed to avoid leaving
TDLS setup pending and to return to the AP path in case anything
goes wrong during the setup attempt.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A transmission failure of the TDLS Setup Request frame (TPK Handshake
M1) results in no further retries and the peer entry being left in state
where all TDLS Setup Request frames from the peer with higher address
would be rejected, thus always resulting in a failure to establish a
TDLS link. Handle the failures in transmission by disabling the link
immediately to ensure the traffic to the peer goes through the AP. This
commit also handles similar transmision failures for TPK Handshake M2
and M3 frames (TDLS Setup Response and Confirm).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The ext_supp_rates passed to merge_byte_arrays would be invalid if not
advertized by the TDLS peer. Thus, validate the argument to avoid
crashes in such cases.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is not much use for enabling WPA without WPA2 nowadays since most
networks have been upgraded to WPA2. Furthermore, the code size savings
from disabling just WPA2 are pretty small, so there is not much
justification for maintaining this build option. Remove it to get rid of
undesired complexity.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit ae8535b6e1 added a new function
wpa_sm_pmf_enabled() which is called from WNM code without ifdefs.
Define a dummy wrapper for this function to fix build if WPA2 is
disabled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 4033935dd9 updated
pmksa_cache_flush() function arguments, but forgot to update the wrapper
function for cases where WPA2 or EAP has been disabled in the build.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The Michael MIC TX and RX keys needs to be swapped in the FT case just
like in all other TKIP key configuration cases. This fixes issues where
TKIP as group cipher resulted in Michael MIC failures being detected for
each received group-addressed frame after FT protocol use.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Define a proper event prefix and include additional information to allow
ESS Dissassociation Imminent event to be used in a wpa_cli action
script.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit c3fea27274 added a call to clear
all other PMKSA cache entries for the same network if the PMKSA cache
entry of the current AP changed. This was needed to fix OKC cases since
the other APs would likely use the new PMK in the future. However, this
ended up clearing entries in cases where that is not desired and this
resulted in needing additional full EAP authentication with networks
that did not support OKC if wpa_supplicant was configured to try to use
it.
Make PMKSA cache entry flushing more limited so that the other entries
are removed only if they used the old PMK that was replaced for the
current AP and only if that PMK had previously been used successfully
(i.e., opportunistic flag was already cleared back to 0 in
wpa_supplicant_key_neg_complete()). This is still enough to fix the
issue described in that older commit while not causing problems for
standard PMKSA caching operations even if OKC is enabled in
wpa_supplicant configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
TDLS responder STA used to retransmit the TDLS Setup Response after 5
seconds if the TDLS Setup Confirm is not received. The initiator would
have enabled the TDLS link and started transmitting the data to the peer
on the TDLS link after transmitting the TDLS Setup Confirm frame. If the
TDLS Setup Confirm frame is not received by the receiver, the
transmissions from the initiator on the direct link would get failed for
the TDLS link not getting enabled on the receiver. This commit reduces
the data delivery failure duration by shortening the retry time of the
TDLS Setup Response frames. The retry limit of the TDLS Response frame
also is increased to ensure that the peer does not miss the frames in
the reduced time period.
Signed-hostap: Sunil Dutt <duttus@codeaurora.org>
The reason code for the teardown request is overwritten for open
mode. This commit removes the code that does so by reverting parts
of commit 0cb12963b6.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's AID is required for the driver to
construct partial AID in VHT PPDU's. Pass this information to the driver
during add/set station operations (well, as soon as the information is
available, i.e., with set station operation currently).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reset ft_completed if STA receives deauthentication
between FT reassoc success and the subsequent initial
mobility authentication and association.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A kernel commit ("mac80211: fix FT roaming") started validating that the
STA entry is marked associated when adding a key. While this is needed
to fix some FT use cases with hardware crypto, it has a side effect of
breaking TDLS key configuration. Work around this by trying to
re-configure the key for the direct link after the STA entry has been
set with all information. In addition, try to tear down the link if
anything goes wrong in key configuration (if both attempts fail) or
enabling the link in the driver.
Signed-hostap: Jouni Malinen <j@w1.fi>
Enhance TDLS Setup Request processing to support both external and
internal TDLS setup for the case where concurrent TDLS initialization
results in the TDLS Setup Request from the peer getting accepted.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_tdls_peer_free() ended up getting called after some of the
parameters from the TDLS Setup Request frame were copied into the struct
wpa_tdls_peer information. This could result in continuing with cleared
information in case the new exchange was the one that is used in
concurrent initialization case or if this is to re-negotiated an
existing TDLS link. The driver would not be provided with all the peer
capabilities correctly in such case.
Fix this by moving the existing_peer check to happen before the
information from the TDLS Setup Request frame is copied.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we accept the peer TPK M1 after having sent our TPK M1, we need to
reject TPK M2 from the peer to avoid going through two TDLS setup
exchanges.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the previously started setup is terminated in case both peers
initiate TDLS link at more or less the same time, disable the old link
to allow the dummy station entry to be deleted from cfg80211 so that a
new entry can be added for the setup direction that will be allowed to
proceed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add NL80211_CMD_UPDATE_FT_IES to support update of FT IEs to the
WLAN driver. Add NL80211_CMD_FT_EVENT to send FT event from the
WLAN driver. This will carry the target AP's MAC address along
with the relevant Information Elements. This event is used to
report received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE).
Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
The information of the peer's VHT capability is required for the
driver to establish a TDLS link in VHT mode with a compatible peer.
Pass this information to the driver when the peer station is
getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The contents of the peer's capability and extended capability
information is required for the driver to perform TDLS P-UAPSD and Off
Channel operations. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's HT capability and the QOS information is
required for the driver to perform TDLS operations. Pass this
information to the driver when the peer station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A TDLS Teardown frame with Reason Code 3 (Deauthenticated because
sending STA is leaving (or has left) IBSS or ESS) shall be transmitted
to all TDLS peer STAs (via the AP or via the direct path) prior to
transmitting a Disassociation frame or a Deauthentication frame to the
AP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The reason code used for calculating the MIC should correspond to the
reason code with which the teardown frame is sent, as the receiver shall
use the one obtained in the frame for validating the MIC.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If an implicit TDLS set up request is obtained on an existing link or an
to be established link, the previous link was not removed. This commit
disables the existing link on a new set up request. Also,
wpa_tdls_reneg() function was invoking wpa_tdls_start() on an already
existing peer for the case of internal setup, which is incorrect. Thus
the invocation of wpa_tdls_start() is removed in wpa_tdls_reneg() and
also this function is renamed to wps_tdls_remove() as it does not
renegotiation rather shall remove the link (if any) for the case of
external setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to have this check copied to each caller since this
needs to be done for every case when a new peer is being added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Peer entries were getting added on every discover request from the peer,
thus resulting in multiple entries with the same MAC address. Ensures
that a check is done for the presence of the peer entry and reuse the
existing entry instead of adding a new one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 6aaac006af modified the
pmksa_cache_init() prototype, but forgot to update the empty wrapper
function which is used when PMKSA caching is not included in the build.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. Previously it was possible to
define CONFIG_IEEE80211V without CONFIG_WNM which would break the build.
In addition, IEEE 802.11v has been merged into IEEE Std 802.11-2012 and
WNM is a better term to use for this new functionality anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
These fields do not use AES keywrap. Instead, they are protected with
management frame protection (and not included if PMF is disabled).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Expiry can always trigger a deauthentication, but otherwise,
deauthentication should only happen when the *current* cache entry is
removed and not being replaced. It should not happen when the current
PMK just happens to match the PMK of the entry being removed, since
multiple entries can have the same PMK when OKC is used and these
entries are often removed at different times.
This fixes an issue where eviction of the oldest inactive entry due to
adding a newer entry to a full cache caused a deauthentication when the
entry being removed had the same PMK as the current entry.
Signed-hostap: Dan Williams <dcbw@redhat.com>
Add pmf=1/2 to wpa_supplicant STATUS command output to indicate that PMF
was negotiated for the connect (1 = optional in this BSS, 2 = required
in this BSS).
Signed-hostap: Jouni Malinen <j@w1.fi>
This function is now unused after the last couple of commits that
removed the last uses, so remove this to keep code simpler since all
places that disassociate, can use deauthentication instead.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Even though the standard currently describes disassociation to be used
for RSN element mismatch between Beacon/Probe Response frames and
EAPOL-Key msg 3/4, this is unnecessary difference from other cases that
deauthenticate. In addition, there is no point in leaving the 802.11
Authentication in place in this case. To keep things simpler, use
deauthentication here to get rid of the only use of
wpa_sm_disassociate().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These values are used with WAPI and CCX and reserving the definitions
here reduces the number of merge conflicts with repositories that
include these functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
This introduces new AKM for SAE and FT-SAE and adds the initial parts
for going through the SAE Authentication frame exchange. The actual SAE
algorithm and new fields in Authentication frames are not yet included
in this commit and will be added separately. This version is able to
complete a dummy authentication with the correct authentication
algorithm and transaction values to allow cfg80211/mac80211 drivers to
be tested (all the missing parts can be handled with
hostapd/wpa_supplicant changes).
Signed-hostap: Jouni Malinen <j@w1.fi>
Try to share most of the cipher information like key and RSC lengths and
suite selector conversions, etc. in wpa_common.c to avoid having similar
code throughout the WPA implementation for handling cipher specific
behavior.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
cur_pmksa was left to NULL during the initial association. This can
result in unexpected behavior, e.g., in expiring PMKSA cache entries
since the current entry is not locked in that case. Fix this by updated
cur_pmksa when adding the initial PMKSA entry during msg 1/4 processing.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If the PMKSA cache is full (i.e., 32 candidates have been seen in scan
results and have not yet expired) then any additional entries can
potentially evict the current/active entry (if it is the oldest entry),
which triggers a pointless local deauthentication. The supplicant
shouldn't replace the current/active entry if it is still valid, but
instead the oldest entry that is *not* the current/active one.
Signed-hostap: Dan Williams <dcbw@redhat.com>
intended-for: hostap-1
