This makes it easier to figure out what failed and allows builbot to
integrate multiple logs and state information about the test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like some virtual host setups are too slow to get
wpa_supplicant initialized under valgrind and this was triggering test
failures. Work around this by using even a longer wait before test case
execution.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like valgrind could not under buildbot with the default file
mode. Fix this by making wpa_supplicant and hostapd binaries readable
and executable by everyone.
Signed-hostap: Jouni Malinen <j@w1.fi>
./run-all.sh can now take an optional argument to select whether to run
all test cases as before (default), to run these under valgrind
("valgrind"), to run P2P test cases with concurrent station interface
("concurrent"), or the concurrent P2P test cases under valgrind
("concurrent-valgrind").
valgrind cases report errors if a test case fails or valgrind reports an
error.
Signed-hostap: Jouni Malinen <j@w1.fi>
print and logger.info() were directing output to different locations
(stdout and stderr, respectively) which resulted in buildbot showing
reordered entries. Use logger consistently to avoid that.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like the NOTE commands can time out in some cases. Avoid
stopping the test run in such a case to get more coverage if this is a
temporary issue.
Signed-hostap: Jouni Malinen <j@w1.fi>
The design for launching AP mode interfaces was changed, but
start-p2p-concurrent.sh was not updated with matching changes.
Signed-hostap: Jouni Malinen <j@w1.fi>
Make sure the connection between each STA and the AP is in working state
between each TDLS setup/teardown operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows more consistent interface to be used regardless of which
P2P driver design is used (especially for P2P management operations
over netdev vs. dedicated P2P_DEVICE).
Signed-hostap: Jouni Malinen <j@w1.fi>
The scan results from old test cases showing different SSID on the AP
can result in false failures, so avoid those by ignoring old scan
results from cfg80211.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Stopping the AP first was not ideal for the test cases since it could
result in wpa_supplicant trying to connect back and start a scan at the
end of a test case and cause problems for the following test case that
tried to scan in the beginning while the previously started scan was
still in progress.
Signed-hostap: Jouni Malinen <j@w1.fi>
Do not print the potentially long list of passed test cases. In case of
failure(s), make sure the failed test list is the last item in the
report.
Signed-hostap: Jouni Malinen <j@w1.fi>
The WPS tests are more prone to fail if scan results from the previous
test cases are allowed to remain in the wpa_supplicant BSS table during
the consecutive test since the test setup uses the same BSSID for the
test APs that change their configuration. Avoid these mostly bogus
issues by enforcing wpa_supplicant to drop and ignore old scan results
during the WPS test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
This removes the unnecessary separation of P2P (no hostapd) and AP
tests. The same scripts can be used to prepare for these tests and to
execute the tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
P2P_PROV_DISC fails if the peer is not fully discovered and the previous
version of the test cases did not force this (i.e., it could have
started PD just based on having seen a Probe Request frame from the
peer).
Signed-hostap: Jouni Malinen <j@w1.fi>
buildbot seems to be running with more limited umask by default and that
prevented the hostapd per-interface socket from being accessed.
Signed-hostap: Jouni Malinen <j@w1.fi>
A virtual station interface in scanning state can change the P2P
operations quite a bit, so running all the P2P tests also in such
setup can increase testing coverage quite a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
The discovery and group formation test cases do not need to run the full
scan as the first step, so get rid of it to make the tests complete more
quickly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is the most common sequence for initiating GO Negotiation, so
include a test case that uses threads to follow both peers at the
same time to allow GO Negotiation to be re-initiated.
Signed-hostap: Jouni Malinen <j@w1.fi>
Command line parameter to run-p2p-tests.py can now be used to select
which test case is run instead of always running all test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
run-p2p-tests.py can now be used to run all P2P test cases. The
actual test cases are defined in test_p2p_*.py files.
Signed-hostap: Jouni Malinen <j@w1.fi>
This will hopefully grow over time to become a much more complete
testing mechanism that uses mac80211_hwsim to verify various
wpa_supplicant and hostapd functions automatically.
Signed-hostap: Jouni Malinen <j@w1.fi>
