Add a helper function to find a certain IE inside IEs buffer by ID and
use this function in several places that implemented similar
functionality locally.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The recent VLAN changes added an explicit code path that sets vlan_desc
= NULL within ap_sta_set_vlan(). This makes some code analyzers warn
about the debug print that could potentially dereference this pointer.
Silence that warning by verifying the pointer more consistently within
this function.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the driver supports 64-bit TX/RX byte counters, use them directly.
The old 32-bit counter extension is maintained for backwards
compatibility with older drivers.
For nl80211 driver interface, the newer NL80211_STA_INFO_RX_BYTES64 and
NL80211_STA_INFO_TX_BYTES64 attributes are used when available. This
resolves the race vulnerable 32-bit value wrap/overflow. Rework RADIUS
accounting to use these for Acct-Input-Octets, Acct-Input-Gigawords,
Acct-Output-Octets, and Acct-Output-Gigawords, these values are often
used for billing purposes.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Previously, stations were added to the driver only after the
(Re)Association Response frame was acked. In the time period between the
station has acked the (Re)Association Response frame and the time the
station was added to the kernel, the station can already start sending
Data frames, which will be dropped by the hardware/driver. In addition
to the data loss, the driver may ignore NDPs with PM bit set from this
STA.
Fix this by setting/adding the STA with associated flag set to the
driver before the AP sends the (Re)Association Response frame with
status success. If the (Re)Association Response frame wasn't acked,
remove the station from the driver.
Note that setting a station to associated state before the non-AP
station acknowledges the (Re)Association Response frame is not compliant
with the IEEE 802.11 standard that specifically states that a non-AP
station should transition to authenticated/associated state only after
it acknowledged the (Re)Association Response frame. However, this is a
justifiable simplification to work around the issue described above since
1. The station will be removed in case it does not acknowledge the
(Re)Association Response frame.
2. All Data frames would be dropped until the station is set to
authorized state and there are no known issues with processing the
other Class 3 frames during the short window before the
acknowledgement is seen.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support for drivers that support full AP client state, i.e., can
handle adding stations that are not associated yet. For such drivers,
add a station after processing the authentication request, instead of
adding it in the association response callback.
Doing so is beneficial in cases where the driver cannot handle the add
station request, in which case it is useless to perform the complete
connection establishment.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
This provides means for determining whether the driver supports full AP
station state and setting the needed STA flags for using this
functionality.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Do not use os_random() that uses a low quality PRNG to generate the
anti-clogging token. The construction can be improved upon by replacing
it with a call to os_get_random(), which uses a high quality PRNG. While
the RFC 5931 explictly recommends not to do this ("SHOULD NOT be from a
source of random entropy"), it does still mandate unpredicability ("MUST
be unpredictable"). The anti-clogging token is most unpredictable when
it is taken from a high quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Remove the fallback dependency on os_random() from the code that gets a
valid DFS channel. This is exceptionally unlikely to ever be called as
the call to os_get_random() is unlikely to fail. The intention is to
facilitate future removal of os_random() as it uses a low quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Remove the fallback dependency on os_random() when generating a WPS pin.
This is exceptionally unlikely to ever be called as the call to
os_get_random() is unlikely to fail. The intention is to facilitate
future removal of os_random() as it uses a low quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Do not use the system clock or os_random() that uses a low quality PRNG
as part of the pseudo-random challenge in auth_shared_key(). The
construction can be improved upon by replacing it with a call to
os_get_random(), which uses a high quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Previously, only mesh Action frames from BLOCKED STA were dropped.
Extend that to drop Authentication frames as well.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The SAE PMKID is calculated with IEEE Std 802.11-2012 11.3.5.4, but the
PMKID was re-calculated with 11.6.1.3 and saved into PMKSA cache. Fix
this to save the PMKID calculated with 11.3.5.4 into the PMKSA cache.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Ensure that characters are represented as unsigned char when using
isblank() and isspace(). These function take in a "int c" argument, but
it needs to be unsigned for the cases where EOF is not indicated.
Signed-off-by: Roy Marples <roy@marples.name>
Shuffle includes above system ones so to fix a compile issue
on NetBSD where the if_type #define from <net/if.h>
conflicts with the wpa_driver_if_type enum.
Signed-off-by: Roy Marples <roy@marples.name>
Shuffle wpa_supplicant includes above system ones so that
to fix a compile problem on NetBSD where if_type #define
conflicts with the wpa_driver_if_type enum.
Signed-off-by: Roy Marples <roy@marples.name>
While most C libraries print "(null)" when NULL is used as an argument
to printf format string %s, this is not really necessary to print here,
so move the debug print to be after the NULL check.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the stations to be assigned to their own vif. It does not
need dynamic_vlan to be set. Make hostapd call ap_sta_set_vlan even if
!vlan_desc.notempty, so vlan_id can be assigned regardless.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This makes vlan_newlink() and vlan_dellink() add tagged VLANs to AP_VLAN
interfaces as given by struct vlan_description.
hostapd_vlan_if_remove() is done in vlan_dellink() as tagged interfaces
need to be removed before the interface can be deleted and a DELLINK
message can be generated.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
To prepare for adding tagged VLAN support in vlan_init.c, vlan_newlink()
and vlan_dellink() are split into multiple functions. This reduces
indention and eases adding tagged VLANs as well.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
1. Add tagged VLAN to struct vlan_description
(compile limited number of tagged VLANs per description)
For k tagged VLANs, the first k entries in vlan_description.tagged
are used. They are sorted in ascending order. All other entries are
zero. This way os_memcmp() can find identical configurations.
2. Let tagged VLANs be parsed from RADIUS Access-Accept
3. Print VLAN %d+ with %d=untagged VID if tagged VLANs are set
4. Select an unused vlan_id > 4096 for new tagged VLAN configurations
5. Add EGRESS_VLAN RADIUS attribute parsing also for untagged VLANs
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Separate uplink configuration (IEEE 802.1q VID) and grouping of stations
into AP_VLAN interfaces.
The int vlan_id will continue to identify the AP_VLAN interface the
station should be assigned to. Each AP_VLAN interface corresponds to an
instance of struct hostapd_vlan that is uniquely identified by int
vlan_id within an BSS.
New: Each station and struct hostapd_vlan holds a struct
vlan_description vlan_desc member that describes the uplink
configuration requested. Currently this is just an int untagged IEEE
802.1q VID, but can be extended to tagged VLANs and other settings
easily.
When the station was about to be assigned its vlan_id, vlan_desc and
vlan_id will now be set simultaneously by ap_sta_set_vlan(). So
sta->vlan_id can still be tested for whether the station needs to be
moved to an AP_VLAN interface.
To ease addition of tagged VLAN support, a member notempty is added to
struct vlan_description. Is is set to 1 if an untagged or tagged VLAN
assignment is requested and needs to be validated. The inverted form
allows os_zalloc() to initialize an empty description.
Though not depended on by the code, vlan_id assignment ensures:
* vlan_id = 0 will continue to mean no AP_VLAN interface
* vlan_id < 4096 will continue to mean vlan_id = untagged vlan id
with no per_sta_vif and no extra tagged vlan.
* vlan_id > 4096 will be used for per_sta_vif and/or tagged vlans.
This way struct wpa_group and drivers API do not need to be changed in
order to implement tagged VLANs or per_sta_vif support.
DYNAMIC_VLAN_* will refer to (struct vlan_description).notempty only,
thus grouping of the stations for per_sta_vif can be used with
DYNAMIC_VLAN_DISABLED, but not with CONFIG_NO_VLAN, as struct
hostapd_vlan is still used to manage AP_VLAN interfaces.
MAX_VLAN_ID will be checked in hostapd_vlan_valid and during setup of
VLAN interfaces and refer to IEEE 802.1q VID. VLAN_ID_WILDCARD will
continue to refer to int vlan_id.
Renaming vlan_id to vlan_desc when type changed from int to struct
vlan_description was avoided when vlan_id was also used in a way that
did not depend on its type (for example, when passed to another
function).
Output of "VLAN ID %d" continues to refer to int vlan_id, while "VLAN
%d" will refer to untagged IEEE 802.1q VID.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Commit 8bcf8de827 ('OpenSSL: Fix memory
leak in PKCS12 additional certificate parsing') tried to fix a memory
leak in both the 1.0.2(and newer) and 1.0.1 branches of PKCS12 parsing.
However, the 1.0.1 case was not properly tested and freeing of the
certificate after a successful SSL_CTX_add_extra_chain_cert() call
resulted in use of freed memory when going through the TLS handshake.
Fix this by not freeing the certificate in that specific case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Ciuple of the nonce comparisons used a strange '!os_memcmp() == 0' to
check if the values were different. While this resulted in correct
behavior, the construction is not exactly clear and clang has started
warning about this (-Wlogical-not-parentheses). Clean this up by using
'os_mecmp() != 0'.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The additional PKCS12 certificates were not freed properly in the loop
added in commit de2a7b796d ('OpenSSL: Use
connection certificate chain with PKCS#12 extra certs').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 5c9a33702f ('OpenSSL: Clean up
crypto_hash_*() to use a single implementation') added a wrapper
function to allow the new OpenSSL API to be used with older OpenSSL
versions. However, the HMAC_CTX_free() wrapper was incorrectly skipping
the call to HMAC_CTX_cleanup() which is still needed to free the
resources OpenSSL allocated internally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
SSL_library_init() does not work properly after EVP_cleanup() starting
from OpenSSL 1.1.0 pre release 3. The automated library init/deinit
functions in that pre release are supposed to handle all initialization
and deinitialiation, so comment out the explicit calls to these function
with OpenSSL 1.1.0 and newer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 1eb87ae48d ('OpenSSL: Use
EVP_CIPHER_CTX_new() to work with OpenSSL 1.1.0') started using
EVP_CIPHER_CTX_new() to allocate EVP_CIPHER_CTX from heap instead of
using stack memory. This commit used incorrect EVP_CIPHER_CTX_reset()
function in number of cases when the allocated memory was supposed to be
freed instead of just reset for reuse. Fix this by using
EVP_CIPHER_CTX_free() properly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
rfkill_init() uses realpath() which allocates memory and that memory was
not freed on the success path.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If SSL_CTX_new(SSLv23_method()) fails, tls_init() error path did not
free the allocated struct tls_data instance.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.
Add a new "pbss" argument to network block. The argument is used
in the following scenarios:
1. When network has mode=2 (AP), when pbss flag is set will start
as a PCP instead of an AP.
2. When network has mode=0 (station), when pbss flag is set will
connect to PCP instead of AP.
The function wpa_scan_res_match() was modified to match BSS according to
the pbss flag in the network block (wpa_ssid structure). When pbss flag
is set it will match only PCPs, and when it is clear it will match only
APs.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.
Add a pbss flag to the relevant structures to support starting a PCP and
connecting to a PCP. Implement support in the nl80211 driver by using
the new PBSS flag attribute.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
NOTE: kqueue has to be closed and re-build after forking. epoll *should*
do the same, but it seems that wpa_supplicant doesn't need it at least.
I have re-worked a little bit of the epoll code (moved into a similar
kqueue function) so it's trivial to requeue epoll if needed in the
future.
Signed-off-by: Roy Marples <roy@marples.name>
This function can be used to re-build eloop socket tables after forking
for eloop implementations that need this.
Signed-off-by: Roy Marples <roy@marples.name>
When a mesh point reconnects by starting from Authentication frame
sequence, the plink count was not decremented from its last connection.
This resulted in leaking peer link count and causing wpa_supplicant to
reject the connection after max_peer_links (default: 99) reconnects.
This was reproduced by pre-configuring 2 mesh points with mesh
credentials. Boot both mesh points and make sure they connect to each
other. Then in a loop reboot one of the mesh points after it
successfully connects while leaving the other mesh point up and running.
After 99 iterations the supplicant on mesh point that is not rebooting
will reject the connection request from the other mesh point.
Fix this by decrementing num_plinks when freeing a STA entry that is
still in PLINK_ESTAB state.
Signed-off-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Setting a long off channel wait time for P2P Action frames when
we know we are already on the right channel may cause a delay in
sending the Action frame (because the driver may not be able to
satisfy the request for long wait time until previous off channel
requests are over). This may be crucial for P2P response frames
that must be sent within 100 milliseconds of receiving the request.
Fix this by adjusting P2P Action frame wait times as follows:
1. For GO Negotiation Response frame, shorten the wait time to 100 ms.
This is reasonable because the peer has just sent us the GO
Negotiation Request frame, so it is known to be on the right
channel and is probably ready to send us the GO Negotiation
Confirmation frame without delay.
2. For GO Negotiation Confirmation, P2P Invitation Response, and
Provision Discovery Response frames, there is no need for wait
time at all as this is the last frame in the exchange. So set
the wait time to 50 ms to ensure there is enough time to send the
frame.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
There is no need to maintain three copies of this functionality even if
it is currently implemented as a single function call.
Signed-off-by: Jouni Malinen <j@w1.fi>
Rework the Acct-Session-Id and Acct-Multi-Session-Id implementation to
give better global and temporal uniqueness. Previously, only 32-bits of
the Acct-Session-Id would contain random data, the other 32-bits would
be incremented. Previously, the Acct-Multi-Session-Id would not use
random data. Switch from two u32 variables to a single u64 for the
Acct-Session-Id and Acct-Multi-Session-Id. Do not increment, this serves
no legitimate purpose. Exclusively use os_get_random() to get quality
random numbers, do not use or mix in the time. Inherently take a
dependency on /dev/urandom working properly therefore. Remove the global
Acct-Session-Id and Acct-Multi-Session-Id values that serve no
legitimate purpose.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
These can get allocated within eapol_auth_alloc(), so it is more logical
to free them in eapol_auth_free() instead of ieee802_1x_free_station()
that ends up calling eapol_auth_free().
Signed-off-by: Jouni Malinen <j@w1.fi>
Need to include these headers in C++ files for adding a binder interface
to wpa_supplicant. So, fix the following C++ compiler errors in them:
1. Add explicit C-style casts in wpa_buf.h header.
2. Move the nested definition of wpa_driver_scan_ssid in driver.h
outside of wpa_driver_scan_params because it is used in another
structure below.
Signed-off-by: Roshan Pius <rpius@google.com>
Event-Timestamp should be sent for all Accounting-Request packets and
only after the system clock has a sane value, not where there's a value
close to the Unix time epoch.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Calculate the required length needed for the extra ANQP elements added
to GAS response buffer instead of using fixed size and truncating the
response if there was not sufficient space.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Fix a possible null pointer dereference in tls_parse_pkcs12() when
loading a PKCS#12 file for the server keys and the file includes extra
certificates.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Need to clear the pac pointer for the first error case to avoid freeing
the previous PAC entry if the following entry has an invalid header.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Acct-Authentic is used to indicate how the user was authenticated and as
such, should not be sent in Accounting-On and Accounting-Off.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Per RFC 2866, 5.10, it is invalid to send Acct-Terminate-Cause in
Accounting-On and Accounting-Off (this is included only when
Acct-Status-Type is set to Stop).
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Ensure that if it is not possible to configure an allowed 20 MHz
channel pair, hostapd falls back to a single 20 MHz channel.
Signed-off-by: Eduardo Abinader <eabinader@ocedo.com>
If an interface is removed, zero the remembered ifindex.
Don't try to set properties on the interface when it is removed.
Signed-off-by: Roy Marples <roy@marples.name>
In the Android-specific case, make ca_cert directive parse a
space-separated list of hex-encoded CA certificate aliases following the
"keystores://" prefix. Server certificate validation should succeed as
long as the chain ends with one of them.
Signed-off-by: Rubin Xu <rubinxu@google.com>
Use the interface index from the correct structure according to the
message instead of assuming rtm_index is correct.
Signed-off-by: Roy Marples <roy@marples.name>
Couple of the image info fields were not printed previously in debug
log. Add those to make this more complete.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to debug AP selection issues in case of a invalid
RSN element or use of customer cipher suites that are not supported by
wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Number of deployed 80 MHz capable VHT stations that do not support 80+80
and 160 MHz bandwidths seem to misbehave when trying to connect to an AP
that advertises 80+80 or 160 MHz channel bandwidth in the VHT Operation
element. To avoid such issues with deployed devices, modify the design
based on newly proposed IEEE 802.11 standard changes.
This allows poorly implemented VHT 80 MHz stations to connect with the
AP in 80 MHz mode. 80+80 and 160 MHz capable stations need to support
the new workaround mechanism to allow full bandwidth to be used.
However, there are more or less no impacted station with 80+80/160
capability deployed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The called function nl80211_ht_vht_overrides() was not freeing "msg"
resource in error cases.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
The PMKSA caching and RSN pre-authentication components were marked as
conditional on IEEE8021X_EAPOL. However, the empty wrappers are needed
also in a case IEEE8021X_EAPOL is defined with CONFIG_NO_WPA.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to follow a debug log from a hostapd process that
manages multiple interfaces.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The ap_sta_deauth_cb and ap_sta_disassoc_cb eloop timeouts are used to
clear a disconnecting STA from the kernel driver if the STA did not ACK
the Deauthentication/Disassociation frame from the AP within two
seconds. However, it was possible for a STA to not ACK such a frame,
e.g., when the disconnection happened due to hostapd pruning old
associations from other BSSes and the STA was not on the old channel
anymore. If that same STA then started a new authentication/association
with the BSS, the two second timeout could trigger during this new
association and result in the STA entry getting removed from the kernel.
Fix this by canceling these eloop timeouts when receiving an indication
of a new authentication or association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
clang started warning about the use of || with constants that came from
PCSC_FUNCS not being enabled in the build. It seems to be easier to just
ifdef this block out completely since that has the same outcome for
builds that do not include PC/SC support.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use compatibility wrapper functions to allow a single implementation
based on the latest OpenSSL API to be used to implement these functions
instead of having to maintain two conditional implementation based on
the library version.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use compatibility wrapper functions to allow a single implementation
based on the latest OpenSSL API to be used to implement these functions
instead of having to maintain two conditional implementation based on
the library version.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The changes needed for OpenSSL 1.1.0 had broken this since LibreSSL is
defining OPENSSL_VERSION_NUMBER in a manner that claims it to be newer
than the current OpenSSL version even though it does not support the
current OpenSSL API.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the final Phase 2 message needed fragmentation, EAP method decision
was cleared from UNCOND_SUCC or COND_SUCC to FAIL and that resulted in
the authentication failing when the EAP-Success message from the server
got rejected. Fix this by restoring the EAP method decision after
fragmentation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now the these functions cannot be made to fail by forcing the memory
allocation fail since the OpenSSL-internal version is used, add
TEST_FAIL check to allow OOM test cases to be converted to use the
TEST_FAIL mechanism without reducing coverage.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The EVP_CIPHER_CTX structure will be made opaque in OpenSSL 1.1.0, so
need to use EVP_CIPHER_CTX_new() with it instead of stack memory. The
design here moves the older OpenSSL versions to use that dynamic
allocation design as well to minimize maintenance effort.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The SSL_CIPHER **cipher argument was marked const in OpenSSL 1.1.0
pre-release 2 similarly to how this is in BoringSSL. Fix build with that
in preparation for supporting OpenSSL 1.1.0.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Free the allocated structure in error cases to remove need for each EAP
method to handle the error cases separately. Each registration function
can simply do "return eap_server_method_register(eap);" in the end of
the function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Free the allocated structure in error cases to remove need for each EAP
method to handle the error cases separately. Each registration function
can simply do "return eap_peer_method_register(eap);" in the end of the
function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Create global init to handle socket calls and route messages.
Register each interface inside the global driver so that
routing messages can find the interface based on rtm_ifindex.
Signed-off-by: Roy Marples <roy@marples.name>
We shouldn't use drv->ctx as it always points to the first BSS. When
using FullMAC driver with multi-BSS support it resulted in incorrect
treating nl80211 events. I noticed with with brcmfmac and BCM43602.
Before my change I was getting "disassociated" on a wrong interface:
wlan0-1: STA 78:d6:f0:00:11:22 IEEE 802.11: associated
wlan0-1: STA 78:d6:f0:00:11:22 WPA: pairwise key handshake completed (RSN)
wlan0: STA 78:d6:f0:00:11:22 IEEE 802.11: disassociated
With this patch it works as expected:
wlan0-1: STA 78:d6:f0:00:11:22 IEEE 802.11: associated
wlan0-1: STA 78:d6:f0:00:11:22 WPA: pairwise key handshake completed (RSN)
wlan0-1: STA 78:d6:f0:00:11:22 IEEE 802.11: disassociated
This doesn't apply to hostapd dealing with SoftMAC drivers when handling
AP SME & MLME is done it hostapd not the firmware.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
If wpa_supplicant was first configured with PKCS #12 -based client
certificate chain and then used with another network profile that used a
different certificate chain from a X.509 certificate PEM file instead of
PKCS#12, the extra certificate chain was not reconstructed properly with
older versions of OpenSSL that 1.0.2. This could result in the
authentication failing due to the client certificate chain not being
complete or including incorrect certificates.
Fix this by clearing the extra certificate chain when setting up a new
TLS connection with OpenSSL 1.0.1. This allows OpenSSL to build the
chain using the default mechanism in case the new TLS exchange does not
use PKCS#12.
The following hwsim test case sequence was able to find the issue:
ap_wpa2_eap_tls_pkcs12 ap_wpa2_eap_tls_intermediate_ca_ocsp
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
n_chans can have only values 1, 2, or 4 in this function, so the -1 case
could never be reached. Remove the unreachable case to get rid of static
analyzer warnings.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
chan is set to the result of pointer arithmetic (pointer to an entry in
an array) that can never be NULL. As such, there is no need to check for
it to be non-NULL before deference. Remove this check to avoid
complaints from static analyzers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Offloading of ACS to the driver changed the design a bit in a way that
iface->current_mode could actually be NULL when the offloaded ACS
mechanism supports band selection in addition to channel selection. This
resulted in a combination that is too complex for static analyzers to
notice. While acs_init() can be called with iface->current_mode == NULL
that is only in the case where WPA_DRIVER_FLAGS_ACS_OFFLOAD is in use.
In other words, the actual ACS functions like acs_cleanup() that would
dereference iface->current_mode are not used in such a case.
Get rid of static analyzer warnings by explicitly checking
iface->current_mode in acs_init() for the case where ACS offloading is
not used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to debug issues with old scan results being ignored
during P2P_FIND. A single rx_time would have been fine with
os_gettime(), but with os_get_reltime(), both rx_time and find_start
values are needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There was a race condition in how the l2_packet sockets got read that
could result in the same socket (e.g., non-bridge) to process both the
EAP-Success and the immediately following EAPOL-Key msg 1/4 instead of
each frame going in alternative order between the bridge and non-bridge
sockets. This could be hit, e.g., if the wpa_supplicant process did not
have enough CPU to process all the incoming frames without them getting
buffered and both sockets reporting frames simultaneously.
This resulted in the duplicated EAP-Success frame getting delivered
twice for processing and likely also the EAPOL-Key msg 1/4 getting
processed twice. While the latter does not do much harm, the former did
clear the EAP authentication state and could result in issues.
Fix this by extended the l2_packet Linux packet socket workaround for
bridge to check for duplicates against the last two received frames
instead of just the last one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the packet socket on the bridge interface to receive
own transmitted frames between the bridge and non-bridge sockets
receiving the same incoming frame from a foreign host. This resulted in
the hash checksum validation step failing to notice a duplicate RX due
to the own frame updating the store hash value.
The own frame did get dropping in RX EAPOL processing, but that was too
late to address the issue with duplicate RX. Fix this by dropping own
frames already in l2_packet layer before checking and updating the last
RX hash value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function can fail at least in theory, so check its return value
before proceeding. This is mainly helping automated test case coverage
to reach some more error paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was reported to fail with Windows 2012r2 with "Invalid Compound_MAC
in cryptobinding TLV". It turns out that the server decided to go
through inner EAP method (EAP-MSCHAPv2 in the reported case) even when
using PEAP fast-reconnect. This seems to be against the [MS-PEAP]
specification which claims that inner EAP method is not used in such a
case. This resulted in a different CMK being derived by the server (used
the version that used ISK) and wpa_supplicant (used the version where
IPMK|CMK = TK without ISK when using fast-reconnect).
Fix this interop issue by making wpa_supplicant to use the
fast-reconnect version of CMK derivation only when using TLS session
resumption and the server having not initiated inner EAP method before
going through the cryptobinding exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous behavior of bursting out all retry attempts of an SD Query
frame during a single search/listen iteration does not look very helpful
in the case where the peer does not ACK the query frame. Since the peer
was found in the search, but is not ACKing frames anymore, it is likely
that it left its listen state and we might as well do something more
useful to burst out a significant number of frames in hopes of seeing
the peer.
Modify the SD Query design during P2P Search to send out only a single
attempt (with likely multiple link-layer retries, if needed) per
search/listen iteration to each peer that has pending SD queries. Once
no more peers with pending queries remain, force another Listen and
Search phase to go through before continuing with the pending SD
queries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If P2P support is included in wpa_supplicant build (CONFIG_P2P=y), but
P2P functionality is explicitly disabled (e.g., "P2P_SET disabled 1"),
couple of AP management frame processing steps did not check against
hapd->p2p_group being NULL and could end up dereferencing a NULL pointer
if a Probe Request frame or (Re)Association Request frame was received
with a P2P IE in it. Fix this by skipping these steps if hapd->p2p_group
is NULL.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit e6dd8196e5 ('Work around Linux
packet socket regression') forgot to add the l2_packet_init_bridge()
wrapper for l2_packet_pcap.c while updating all the other l2_packet
options. This resulted in wpa_supplicant build failing due to missing
l2_packet_init_bridge() function when using CONFIG_L2_PACKET=pcap in
wpa_supplicant/.config. Fix this by adding the wrapper function.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new wps_force_{auth,encr}_types parameters can be used in test build
(CONFIG_WPS_TESTING) to force wpa_supplicant to use the specified value
in the Authentication/Encryption Type flags attribute. This can be used
to test AP behavior on various error cases for which there are
workarounds to cover deployed device behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some deployed implementations seem to advertise incorrect information in
this attribute. A value of 0x1b (WPA2 + WPA + WPAPSK + OPEN, but no
WPA2PSK) has been reported to be used. Add WPA2PSK to the list to avoid
issues with building Credentials that do not use the strongest actually
supported authentication option (that device does support WPA2PSK even
when it does not claim it here).
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the Registrar code to generate a Credential with
auth type WPAPSK (i.e., WPA v1) with encr type AES if the Enrollee
claimed support for WPAPSK and not WPA2PSK while the AP was configured
in mixed mode WPAPSK+WPA2PSK regardless of how wpa_pairwise (vs.
rsn_pairwise) was set since encr type was selected from the union of
wpa_pairwise and rsn_pairwise. This could result in the Enrollee
receiving a Credential that it could then not use with the AP.
Fix this by masking the encryption types separately on AP based on the
wpa_pairwise/rsn_pairwise configuration. In the example case described
above, the Credential would get auth=WPAPSK encr=TKIP instead of
auth=WPAPSK encr=AES.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it somewhat easier for the station to be able to receive and
process the encrypted WNM-Notification frames that the AP previously
sentt immediately after receiving EAPOL-Key msg 4/4. While the station
is supposed to have the TK configured for receive before sending out
EAPOL-Key msg 4/4, not many actual implementations do that. As such,
there is a race condition in being able to configure the key at the
station and the AP sending out the first encrypted frame after EAPOL-Key
4/4. The extra 100 ms time here makes it more likely for the station to
have managed to configure the key in time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add SSL_SESSION_get_master_key() compatibility wrapper for older OpenSSL
versions to be able to use the new openssl_tls_prf() implementation for
OpenSSL 1.1.0 with all supported versions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
SSL_get_client_random() and SSL_get_server_random() will be added in
OpenSSL 1.1.0. Provide compatibility wrappers for older versions to
simplify the tls_connection_get_random() implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The OpenSSL project will not support version 1.0.0 anymore. As there
won't be even security fixes for this branch, it is not really safe to
continue using 1.0.0 and we might as well drop support for it to allow
cleaning up the conditional source code blocks.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The OpenSSL project will not support version 0.9.8 anymore. As there
won't be even security fixes for this branch, it is not really safe to
continue using 0.9.8 and we might as well drop support for it to allow
cleaning up the conditional source code blocks.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the p2p->pending_listen_freq to be left indicating
that there is a pending ROC for a listen operation if a P2P_FIND command
was timed to arrive suitably between a previous Listen operation issuing
a ROC request and the kernel code starting that request. This could
result in the P2P state machine getting stuck unable to continue the
find ("P2P: p2p_listen command pending already").
Fix this by clearing p2p->pending_listen_freq when starting P2P_FIND
command execution.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new optional group_ssid=<hexdump> argument in the P2PS-PROV-DONE
event can be used to help in identifying the exact group if there have
been multiple groups with the same P2P Interface Address in short period
of time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When we receive FST Setup Request when session already exists, the
following validations take place:
1. we drop the frame if needed according to MAC comparison
2. we drop the frame if the session is "not pending", i.e., if FST
Setup Response was already exchanged (sent or received).
There are two issues with the above:
1. MAC comparison is relevant only before the Setup Response exchange.
In other words, Setup Request should not be dropped due to MAC
comparison after Setup Response has been exchanged.
2. Receiving Setup Request after Setup Response exchange most likely
means that FST state machine is out of sync with the peer. Dropping
the Setup Request will not help solve this situation.
The fix is:
1. do MAC comparison only if session is "pending", i.e., Setup Response
was not yet exchanged.
2. In case Setup Response was already exchanged, reset our session and
handle the Setup Request as if it arrived when session doesn't exist.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Explicitly check for the failure event to include a certificate before
trying to build the event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While this could in theory be claimed to be ready for something to be
added to read a field following the server_write_IV, it does not look
likely that such a use case would show up. As such, just remove the
unused incrementing of pos at the end of the function to get rid of a
useless static analyzer complaint.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes some static analyzers complain about stored value never being
read. While it is good to clear some other temporary variables, this
local variable i has no security private information (it has a fixed
value of 20 here) and trying to clear it to 0 does not add any value.
Remove that part of the "wipe variables" to avoid one useless static
analyzer complaint.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
As a dedicated P2P Device interface does not have a network
interface associated with it, trying to call linux_iface_up()
on it would always fail so this call can be skipped for
such an interface.
Getting interface nlmode can be done only after bss->wdev_id is
set, so move this call to wpa_driver_nl80211_finish_drv_init(),
and do it only in case the nlmode != NL80211_IFTYPE_P2P_DEVICE.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
IEEE Std 802.11-2012 11.3.5.4 specifies the PMKID for SAE-derived keys
as:
L((commit-scalar + peer-commit-scalar) mod r, 0, 128)
This is already calculated in the SAE code when the PMK is derived, but
not saved anywhere. Later, when generating the PMKID for plink action
frames, the definition for PMKID from 11.6.1.3 is incorrectly used.
Correct this by saving the PMKID when the key is generated and use it
subsequently.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Since hostapd supports ACS now, let's enable its support in
wpa_supplicant as well when starting AP mode.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
[u.oelmann@pengutronix.de: adjusted added text in defconfig]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Let's reuse hostapd code for such handling. This will be useful to get
ACS support into wpa_supplicant where this one needs to handle the
survey event so it fills in the result ACS subsystem will require.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
The data->state == WAIT_FRAG_ACK case is already handling all cases
where data->out_buf could be non-NULL, so this additional check after
the WAIT_FRAG_ACK steps cannot be reached. Remove the duplicated dead
code.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, a fixed 1300 fragment_size was hardcoded. Now the EAP
profile parameter fragment_size can be used to override this.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows RADIUS failover to be performed if send() return EACCES
error which is what happens after a recent Linux kernel commit
0315e382704817b279e5693dca8ab9d89aa20b3f ('net: Fix behaviour of
unreachable, blackhole and prohibit') for a local sender when route type
is prohibit.
This fixes the hwsim test case radius_failover when running against a
kernel build that includes that commit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 986de33d5c ('Convert remaining SSID
routines from char* to u8*') started using wpa_ssid_txt() to print out
the SSID for the Called-Station-Id attribute in RADIUS messages. This
was further modified by commit 6bc1f95613
('Use printf escaping in SSID-to-printable-string conversion') to use
printf escaping (though, even without this, wpa_ssid_txt() would have
masked characters).
This is not desired for Called-Station-Id attribute. While it is defined
as a "String", RFC 2865 indicates that "a robust implementation SHOULD
support the field as undistinguished octets.".
Copy the SSID as an array of arbitrary octets into Called-Station-Id to
avoid any kind of masking or escaping behavior. This goes a step further
from the initial implementation by allowing even the possible (but
unlikely in practical use cases) 0x00 octet in the middle of an SSID.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends multi-OCSP support to verify status for intermediate CAs in
the server certificate chain.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ocsp=3 extends ocsp=2 by require all not-trusted certificates in the
server certificate chain to receive a good OCSP status. This requires
support for ocsp_multi (RFC 6961). This commit is only adding the
configuration value, but all the currently included TLS library wrappers
are rejecting this as unsupported for now.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a minimal support for using status_request_v2 extension and
ocsp_multi format (OCSPResponseList instead of OCSPResponse) for
CertificateStatus. This commit does not yet extend use of OCSP stapling
to validate the intermediate CA certificates.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd with the internal TLS server implementation to
support the extended OCSP stapling mechanism with multiple responses
(ocsp_stapling_response_multi).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a new hostapd configuration parameter
ocsp_stapling_response_multi that can be used similarly to the existing
ocsp_stapling_response, but for the purpose of providing multiple cached
OCSP responses. This commit adds only the configuration parameter, but
does not yet add support for this mechanism with any of the supported
TLS implementations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for hostapd-as-authentication-server to be build with
the internal TLS implementation and OCSP stapling server side support.
This is more or less identical to the design used with OpenSSL, i.e.,
the cached response is read from the ocsp_stapling_response=<file> and
sent as a response if the client requests it during the TLS handshake.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for hostapd-as-authentication-server to be build
against GnuTLS with OCSP stapling server side support. This is more or
less identical to the design used with OpenSSL, i.e., the cached
response is read from the ocsp_stapling_response=<file> and sent as a
response if the client requests it during the TLS handshake.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This message is sent at MSG_INFO level and it is supposed to go out even
even debug messages were to be removed from the build. As such, use
wpa_msg() instead of wpa_dbg() for it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This error case in own buffer lengths being too short was not handled
properly. While this should not really happen since the wpabuf
allocation is made large for the fixed cases that are currently
supported, better make eap_eke_prot() safer if this functionally ever
gets extended with a longer buffer need.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the five second timeout was added at the beginning of the
full GAS query and it was not replenished during fragmented exchanges.
This could result in timing out a query if it takes significant time to
go through the possibly multiple fragments and long comeback delay.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of using default list of methods, reject a configuration with an
unsupported EAP method at the time the main TLS method is being
initialized.
Signed-off-by: Jouni Malinen <j@w1.fi>
When AES-WRAP was used to protect the EAPOL-Key Key Data field, this was
decrypted using a temporary heap buffer with aes_unwrap(). That buffer
was not explicitly cleared, so it was possible for the group keys to
remain in memory unnecessarily until the allocated area was reused.
Clean this up by clearing the temporary allocation explicitly before
freeing it.
Signed-off-by: Jouni Malinen <j@w1.fi>
IPMK and CMK are derived from TK when using TLS session resumption with
PEAPv0 crypto binding. The EAP-PEAP peer implementation already
supported this, but the server side did not.
Signed-off-by: Jouni Malinen <j@w1.fi>
eap_peap_parse_phase1() returned 0 unconditionally, so there was no need
for that return value or the code path that tried to address the error
case.
Signed-off-by: Jouni Malinen <j@w1.fi>
On systems that have multiple WLAN rfkill instances, the rfkill code
can become confused into thinking that the device was unblocked when
in fact it wasn't, because it only matches on the WLAN type.
Since it then stores the new (unblocked) state from the wrong rfkill
instance, it will never retry the failing IFF_UP operation and the
user has to toggle rfkill again, or otherwise intervene manually, in
this case to get back to operational state.
Fix this by using the existing (but unused) ifname argument when the
rfkill instance is created to match to a specific rfkill index only.
As a P2P Device interface does not have a netdev interface associated
with it, use the name of a sibling interface to initialize the rfkill
context for the P2P Device interface. For nl80211, as the wiphy index
is known only after getting the driver capabilities from the kernel,
move the initialization of the rfkill object to
wpa_driver_nl80211_finish_drv_init().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The rfkill processing in nl80211 driver assumes that the
INTERFACE_ENABLED/DISABLED will be also issued, so does not do much in
the rfkill callbacks. However, as a P2P Device interface is not
associated with a network interface, these events are not issued for it.
Handle rfkill events for the P2P_DEVICE interface by faking the
INTERFACE_ENABLED/DISABLED.
Signed-off-by: Moshe Benji <Moshe.Benji@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The Setup Response timer is relatively fast (500 ms) and there are
instances where it fires on the responder side after the initiator has
already sent out the TDLS Setup Confirm frame. Prevent the processing of
this stale TDLS Setup Response frame on the initiator side.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Fix mostly theoretical NULL pointer dereference in
wpa_debug_open_linux_tracing() if /proc/mounts were to return a
malformed line.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
This patch fixes an issue with an invalid phase2 parameter value
auth=MSCHAPv2 getting interpreted as auth=MSCHAP (v1) which could
degrade security (though, only within a protected TLS tunnel). Now when
invalid or unsupported auth= phase2 parameter combinations are
specified, EAP-TTLS initialization throws an error instead of silently
doing something.
More then one auth= phase2 type cannot be specified and also both auth= and
autheap= options cannot be specified.
Parsing phase2 type is case sensitive (as in other EAP parts), so phase2
parameter auth=MSCHAPv2 is invalid. Only auth=MSCHAPV2 is correct.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[Use cstr_token() to get rid of unnecessary allocation; cleanup]
Signed-off-by: Jouni Malinen <j@w1.fi>
There are two types of memory processing functions in the file
atheros_driver.c, such as memory and os_memory. Unify the processing
functions into one type which has the prefix "os_".
Signed-off-by: Matt Woods <matt.woods@aliyun.com>
This adds a CTRL-EVENT-EAP-TLS-CERT-ERROR and CTRL-EVENT-EAP-STATUS
messages with 'bad certificate status response' for cases where no valid
OCSP response was received, but the network profile requires OCSP to be
used.
Signed-off-by: Jouni Malinen <j@w1.fi>
This completes OCSP stapling support on the TLS client side. Each
SingleResponse value is iterated until a response matching the server
certificate is found. The validity time of the SingleResponse is
verified and certStatus good/revoked is reported if all validation step
succeed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds the next step in completing TLS client support for OCSP
stapling. The BasicOCSPResponse is parsed, a signing certificate is
found, and the signature is verified. The actual sequence of OCSP
responses (SignleResponse) is not yet processed in this commit.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds the next step for OCSP stapling. The received OCSPResponse is
parsed to get the BasicOCSPResponse. This commit does not yet process
the BasicOCSPResponse.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the internal TLS client implementation to accept
CertificateStatus message from the server when trying to use OCSP
stapling. The actual OCSPResponse is not yet processed in this commit,
but the CertificateStatus message is accepted to allow the TLS handshake
to continue.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the internal TLS implementation to request server
certificate status using OCSP stapling. This commit is only adding code
to add the request. The response is not yet used.
Signed-off-by: Jouni Malinen <j@w1.fi>
This prints the received ServerHello extensions into the debug log and
allows handshake to continue even if such extensions are included.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the internal TLS implementation to parse a private key and a
certificate from a PKCS #12 file protected with
pbeWithSHAAnd3-KeyTripleDES-CBC.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support for decrypting private keys protected with the old
PKCS #12 mechanism using OID pbeWithSHAAnd3-KeyTripleDES-CBC.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support for optional functionality to validate server
certificate chain in TLS-based EAP methods in an external program.
wpa_supplicant control interface is used to indicate when such
validation is needed and what the result of the external validation is.
This external validation can extend or replace the internal validation.
When ca_cert or ca_path parameter is set, the internal validation is
used. If these parameters are omitted, only the external validation is
used. It needs to be understood that leaving those parameters out will
disable most of the validation steps done with the TLS library and that
configuration is not really recommend.
By default, the external validation is not used. It can be enabled by
addingtls_ext_cert_check=1 into the network profile phase1 parameter.
When enabled, external validation is required through the CTRL-REQ/RSP
mechanism similarly to other EAP authentication parameters through the
control interface.
The request to perform external validation is indicated by the following
event:
CTRL-REQ-EXT_CERT_CHECK-<id>:External server certificate validation needed for SSID <ssid>
Before that event, the server certificate chain is provided with the
CTRL-EVENT-EAP-PEER-CERT events that include the cert=<hexdump>
parameter. depth=# indicates which certificate is in question (0 for the
server certificate, 1 for its issues, and so on).
The result of the external validation is provided with the following
command:
CTRL-RSP-EXT_CERT_CHECK-<id>:<good|bad>
It should be noted that this is currently enabled only for OpenSSL (and
BoringSSL/LibreSSL). Due to the constraints in the library API, the
validation result from external processing cannot be reported cleanly
with TLS alert. In other words, if the external validation reject the
server certificate chain, the pending TLS handshake is terminated
without sending more messages to the server.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not override the parsing error with the "PAC block not terminated
with END" message if the reason for the END line not yet being seen is
in failure to parse an earlier line.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible to hit a NULL pointer dereference if Session-Id
derivation failed due to a memory allocation failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
The EVP_MD_CTX and HMAC_CTX definitions are now hidden from applications
using OpenSSL. Fix compilation issues with OpenSSL 1.1.x-pre1 by using
the new API for allocating these structures.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This FTIE needs to be an exact copy of the one in (Re)Association
Response frame. Copy the stored element rather than building a new copy
that would not have the correct MIC value. This is needed to fix PTK
rekeying after FT protocol run.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The FTIE from (Re)Association Response frame was copied before
calculating the MIC. This resulted in incorrect value being used when
comparing the EAPOL-Key msg 2/4 value in case PTK rekeying was used
after FT protocol run. Fix this by storing the element after the MIC
field has been filled in.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_insert_pmkid() did not support cases where the original RSN IE
included any PMKIDs. That case can happen when PTK rekeying through
4-way handshake is used after FT protocol run. Such a 4-way handshake
used to fail with wpa_supplicant being unable to build the EAPOL-Key msg
2/4.
Fix this by extending wpa_insert_pmkid() to support removal of the old
PMKIDs, if needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to interpret AP side debug log for a case where a
station specifies in unsupported management group cipher.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new wpa_supplicant control interface command "TEST_ASSOC_IE
<hexdump>" can now be used to override the WPA/RSN IE for Association
Request frame and following 4-way handshake to allow protocol testing of
AP side processing of WPA/RSN IE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the internal TLS support for PKCS #5 v2.0 PBES2 private key
format with des-ede3-cbc encryption and PBKDF2 SHA-1.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds experimental support for using OCSP with libcurl that is built
against BoringSSL. This needs small modifications to libcurl to allow
CURLOPT_SSL_VERIFYSTATUS to be used to call
SSL_enable_ocsp_stapling(connssl->handle) in ossl_connect_step1().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to share the OCSP implementation needed for
BoringSSL outside tls_openssl.c. For now, this is mainly for
http_curl.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
BoringSSL modified the struct sha_state_st (SHA_CTX) definition by
converting h0..h4 with h[5] array. This broke wpa_supplicant/hostapd
build with EAP-SIM enabled. BoringSSL restored the old version for
ANDROID builds, but only the new version is currently defined for
non-Android cases. For now, fix this by having matching selection in
fips_prf_openssl.c based on OPENSSL_IS_BORINGSSL and ANDROID defines.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
OpenSSL 1.1.x will apparently go out with "SSLeay" renamed in the API to
"OpenSSL", which broke the build here for fetching the version of the
running OpenSSL library when wpa_supplicant/hostapd is built against the
current OpenSSL snapshot.
Signed-off-by: Jouni Malinen <j@w1.fi>
These needs to be cancelled so that the kernel driver does not get left
with all old entries blocking other offchannel operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows multiple external registrars to execute a WPS protocol run
with a WPS AP over UPnP. Previously, hostapd supported only a single WPS
peer entry at a time and if multiple ERs tried to go through a WPS
protocol instance concurrently, only one such exchange could succeed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add 'scan plans' to driver scan parameters for scheduled scan.
Each 'scan plan' specifies the number of iterations to run the scan
request and the interval between iterations. When a scan plan
finishes (i.e., it was run for the specified number of iterations),
the next scan plan is executed. The last scan plan will run
infinitely.
The maximum number of supported scan plans, the maximum number of
iterations for a single scan plan and the maximum scan interval
are advertised by the driver.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
conn->session_resumed was not set to 1 after successful use of a TLS
session ticket with EAP-FAST. This resulted in the wpa_supplicant STATUS
tls_session_reused showing incorrect value (0 instead of 1) when
EAP-FAST PAC was used. Fix this by setting conn->session_resumed = 1
when TLS handshake using the session ticket succeeds.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit af851914f8 ('Make
tls_connection_get_keyblock_size() internal to tls_*.c') broke
tls_connection_prf() with the internal TLS implementation when using
skip_keyblock=1. In practice, this broke EAP-FAST. Fix this by deriving
the correct number of PRF bytes before skipping the keyblock.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the server/client certificate includes the extKeyUsage extension,
verify that the listed key purposes include either the
anyExtendedKeyUsage wildcard or id-kp-serverAuth/id-kp-clientAuth,
respectively.
Signed-off-by: Jouni Malinen <j@w1.fi>
md4_vector(), md5_vector(), sha1_vector(), and sha256_vector() already
supported TEST_FAIL() with the OpenSSL crypto implementation, but the
same test functionality is needed for the internal crypto implementation
as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for some NFC DH generation error paths to leak memory
since the old private/public key was not freed if an allocation failed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The internal TLS client implementation in wpa_supplicant can now be used
with the phase2 parameters tls_disable_tlsv1_0=1, tls_disable_tlsv1_1=1,
and tls_disable_tlsv1_2=1 to disable the specified TLS version(s).
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it simpler to add support for new TLS_CONN_* flags without
having to add a new configuration function for each flag.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows wpa_supplicant to return eap_tls_version STATUS information
when using the internal TLS client implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The internal TLS client implementation can now be used with
ca_cert="probe://" to probe the server certificate chain. This is also
adding the related CTRL-EVENT-EAP-TLS-CERT-ERROR and
CTRL-EVENT-EAP-PEER-CERT events.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the internal TLS client implementation to support signature
algorithms SHA384 and SHA512 in addition to the previously supported
SHA256.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since we support only SHA256 (and not the default SHA1) with TLS v1.2,
the signature_algorithms extensions needs to be added into ClientHello.
This fixes interop issues with the current version of OpenSSL that uses
the default SHA1 hash if ClientHello does not specify allowed signature
algorithms.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit adds support for validating certificates with SHA384 and
SHA512 hashes. Those certificates are now very common so wpa_supplicant
needs support for them.
SHA384 and SHA512 hash functions are included in the previous commit.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
These will be used with the internal TLS implementation to extend hash
algorithm support for new certificates and TLS v1.2.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
