The previous designed worked since wpa_supplicant did not track pending
request state. With such tracking added, this test case needs to make
sure there is a pending operation when injecting the invalid response.
Signed-off-by: Jouni Malinen <j@w1.fi>
On slow machines or inside VM it may take some time for "DISCONNECTED"
event to arrive. Since the retry delay counter is started already, it
may result in less than 5 seconds time between "DISCONNECTED" and
"CONNECTED" events.
Fix the test by taking more accurate timestamps between the events.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
It was possible for the BTM Request with no matching BSSIDs to cause
wpa_supplicant-initated roam to a better BSS (5 GHz band preferred) when
finding the second AP in a scan started by that BTM Request. This could
make the following step in the test case fail. Fix this by asking
another channel to be scanned to postpone discovery of the other AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
The cfg80211 connect command extension to allow roaming request from
user space while connect was added to the kernel, so uncomment the
previously commented out TODO item to verify this behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the cfg80211 regulatory code to get confused if the
disconnection and user hint to set country code to 00 happened
immediately after the BTM-initiated roam. The country IE update seemed
to be performed just before the 00 user hint and that resulted in
cfg80211 intersecting the regulatory domains instead of clearing to 00.
This resulted in the following test cases being unable to set the
country code.
This happened with the following test case sequence:
wnm_bss_tm_scan_needed_e4 wnm_bss_tm_scan_not_needed
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that the AP responds to a BSS transition management query that
includes candidates unknown to the AP.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Use a local variable for the STA address instead of fetching it
separately for each operation. Dump control interface monitor events
between each test message to avoid increasing the socket output queue
unnecessarily.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The second AP is not really needed in this test case that verifies
parsing of various different BSs Transition Management Request frame
payloads.
Signed-off-by: Beni Lev <beni.lev@intel.com>
wnm_bss_tm_global uses an unknown country code to use Table E-4. Extend
that with otherwise identical test case wnm_bss_tm_global4, but with the
country string explicitly indicating use of Table E-4 while using a
known country code.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
After successfully passing the 525 tests on a remote setup mark the
tests as remote compatible.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Use a monitor interface given in the command line that is not also a
station or an AP as a monitor running wlantest on the channel used by
the test. This makes all the tests that use wlantest available for
execution on real hardware on remote hosts.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (4) converts the cases that call hostapd.add_ap() from a
helper function that got apdev[i] as an argument.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (1) converts the cases where apdev[#]['ifname'] was used as
the argument to hostapd.add_ap().
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
For now, this is not enforcing cfg80211 reassociation since the needed
changes do not yet exist in the upstream kernel. Once those changes are
accepted, the TODO note in the test case can be addressed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This tests BSS Transition Management Query frame generation with
candidate list and transmission of the following request and response
frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add tests to verify that MBO IE in BSS Transition Management Request
frame is parsed correctly:
1. The MBO transition reason code is received by the MBO station.
2. The MBO cellular data connection preference is received by the
MBO station.
3. The MBO station does not try to connect to the AP until the retry
delay is over.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
It was possible for the Action frame used for entring WNM Sleep Mode to
get dropped on the AP side due to it arriving prior to having processed
EAPOL-Key message 4/4 due to a race condition between Data and
Management frame processing paths. Avoid this by waiting for
AP-STA-CONNECTED event from hostapd prior to trying to enter WNM Sleep
Mode. In addition, make the check for the STA flag change more robust by
allowing the wait to be a bit longer with a loop that terminates as soon
as the flag has changed.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for regulatory domain changes to "leak" into following
test cases in number of cases where the cfg80211 BSS table remained
after regulatory domain had been restored to world roaming. Try to make
this less likely to occur by explicitly clearing BSS table at the end of
test cases that use different regulatory domain. This makes P2P test
cases that verify channel selection based on world roaming rules more
robust.
Signed-off-by: Jouni Malinen <j@w1.fi>
