Commit graph

14 commits

Author SHA1 Message Date
Jouni Malinen
4466fe6541 tests: VHT and 40 MHz channel
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-20 18:44:48 +02:00
Jouni Malinen
9d7fdac5b3 tests: Try to clear scan results after regulatory domain changes
It was possible for regulatory domain changes to "leak" into following
test cases in number of cases where the cfg80211 BSS table remained
after regulatory domain had been restored to world roaming. Try to make
this less likely to occur by explicitly clearing BSS table at the end of
test cases that use different regulatory domain. This makes P2P test
cases that verify channel selection based on world roaming rules more
robust.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-15 01:32:01 +02:00
Jouni Malinen
c2bf6d3afc tests: SIGNAL_POLL in 160 and 80+80 MHz channels
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-11 23:37:02 +02:00
Jouni Malinen
146374019a tests: Add missing test descriptions
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:06 +02:00
Jouni Malinen
d4792c0cb7 tests: Channel switch with VHT80
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-25 11:29:28 +03:00
Jouni Malinen
a8375c94c0 tests: Pass wpas/hapd instance to test_connectivity()
This makes it easier to replace data connectivity testing to use
something else than local hwsim_test binary on the controller device.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-19 17:54:49 +03:00
Jouni Malinen
74ed673f33 tests: VHT 80+80 MHz
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-09 14:27:23 +03:00
Jouni Malinen
6259fd814b tests: VHT with 160 MHz channel width
Since this requires a recent CRDA version and updated wireless-regdb, do
not report failures yet (i.e., indicate that the test case was skipped
if AP startup fails).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-08 18:18:39 +03:00
Jouni Malinen
6acecce1fe tests: hostapd configuration parameters
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-30 18:07:05 +03:00
Jouni Malinen
fdc02e4caf tests: Require HT/VHT as BSS membership selector in Supp Rates
These are similar to the previous cases, but with supported rate set
limited to allow the BSS membership selector to fit into that element
instead of Ext Supp Rates.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-29 10:39:32 +02:00
Jouni Malinen
145f35bf30 tests: Verify HT/VHT required rejection
Previously, only the case of STA supporting HT/VHT was tested. Now both
cases are verified.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-23 19:49:12 +02:00
Johannes Berg
ea7526bfb3 tests: Verify VHT20 with center freq seq0 set to zero
This was found through a mac80211 bug which didn't correctly accept a
center segment 0 value of zero, so the test will fail until the mac80211
bug is fixed.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-03-14 17:07:18 +02:00
Jouni Malinen
a4292b3f3b tests: require_vht=1
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-13 23:17:04 +02:00
Jouni Malinen
7cd0aa7ea8 tests: VHT functionality
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 22:39:18 +02:00