Add a comment to note which fields are expected to be updated by the
driver. In addition, reorder subfield writing to match the order in
which the fields are in the frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
The request from the AP was encoded incorrectly for this test case and
an active scan was requested instead of the passive one that was
supposed to be used here.
Signed-off-by: Jouni Malinen <j@w1.fi>
ieee80211_chan_to_freq() is not really meant for conversion of 20 MHz
primary channel numbers for wider VHT channels, so handle those as
special cases here for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpabuf_resize() can handle the initial allocation of a wpabuf and all
the other callers of wpas_rrm_report_elem() were already using a pointer
to a pointer and a wpabuf_resize() call. Simplify this by resizing the
wpabuf (if needed) within wpas_rrm_report_elem() instead of having to
calculate the needed size in all the callers. Thsi is also fixing one of
the allocation sizes to use the correct size instead of a size of a
struct that has nothing to do with the allocation (but is larger than
the needed five octets, so does not break anything).
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace the TEST_ALLOC function wpas_beacon_rep_no_results with an
earlier function in the backtrace and wpabuf_resize() in preparation to
a code change that allows the compiler to optimize out
wpas_beacon_rep_no_results().
Signed-off-by: Jouni Malinen <j@w1.fi>
There is only a single caller for wpas_rrm_send_neighbor_rep_request()
and it unconditionally uses a callback function, so cb cannot be NULL
here and there is no need for additional complexity and extra code size
to check for it explicitly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Authentication and Deauthentication frames are not used in DMG/IEEE
802.11ad networks. For DMG/IEEE 802.11ad the following was implemented:
Upon receiving association request, allocate the sta object and
initialize it as if authentication took place. Upon receiving
disassociation, deallocate the sta object.
ap_sta_disassociate/ap_sta_deauthenticate/ap_sta_disconnect all use
disassociation instead of deauthentication. In driver_nl80211,
i802_sta_deauth() is routed to i802_sta_disassoc().
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Supported Rates element is not present in DMG/IEEE 802.11ad frames. Make
copy_supp_rates() immediately return with success if hardware mode is
IEEE 802.11ad.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Previously, the check was done after we reached the maximum and another
scan was already triggered.
While at it, remove an irrelevant comment that the previous change in
the logic here missed.
Signed-off-by: Beni Lev <beni.lev@intel.com>
It was possible that nl80211_get_hw_feature_data() function would return
NULL when num_modes is not set to zero. This might result in a later crash
when accessing hw.modes. This may be reproduced with hwsim oom tests, for
example, dbus_connect_oom.
Fix that by zeroing num_modes if NULL is returned.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The channel switch command is intended for the GO interface, but
it was not sent on the group control interface. For configurations
that use a separate interface for P2P groups, this will fail the test.
Fix this by sending the channel switch command on the group control
interface and waiting for the channel switch event on the group
control interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This fixes the netlink attribute identifier for the scan flags when
using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, SIM state change with SIM_STATE_ERROR cleared all PMKSA
entries (including non-SIM networks). Limit this to networks which use
SIM-based authentication methods to avoid unnecessarily removal of PMKSA
entries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The pending neighbor report state needs to be cleared on error path here
to avoid getting stuck with being unable to perform any additional
neighbor reports during the association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow shorter request since the subelements are optional to include.
Also print the hexdump of the subelements into debug log.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The requested behavior can be approximated for most use cases even if
the driver does not support reporting exact TSF values for frames.
Enable this capability for all drivers to make beacon report processing
more useful for a common use case.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface event "BEACON-RESP-RX <STA address>
<dialog token> <report mode> <beacon report>" is now used to report
received beacon reports as a reponse to the REQ_BEACON operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new BEACON-REQ-TX-STATUS control interface event is now used to
report whether a beacon request (from REQ_BEACON command) was delivered
successfully. This event has the following parameters: <STA address>
<dialog token> <ack=0/1>.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new control interface command "REQ_BEACON <STA addr>
[req_mode=<mode>] <beacon request>" can now be used to request hostapd
to transmit a measurement request to request a beacon report from an
associated STA. This command returns the assigned dialog token (1-255)
or FAIL on failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
rrm_beacon_report=1 can now be used to make hostapd advertise capability
for beacon reports (passive, active, table). Actual mechanism for
sending out beacon requests will be added in separate commits.
Signed-off-by: Jouni Malinen <j@w1.fi>
The special parameters for beacon report scan are not needed for the
beacon report when using the beacon table measurement mode. Advertise
support for this case regardless of whether the driver supports the scan
parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
The loop to add hash values was supposed to be limited to at most 10000
values, but the count variable was not being decremented in the loop.
Fix this by decrementing counting for each iteration. This fixes
ANQP-element format in the unlikely case of there being more than 10000
configuration realms.
Signed-off-by: Jouni Malinen <j@w1.fi>
Beacon Report Radio Measurement is defined in IEEE Std 802.11-2016,
11.11.9.1. Beacon Report is implemented by triggering a scan on the
requested channels with the requested parameters.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This conversion will be done several times in the code, so add a helper
function that does this conversion.
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
Extend verify_channel() to return whether IR is allowed on the channel
or not, and make it a global function so it can be used in other files,
too. This makes this function useful for checking not only if a channel
is supported but also if it is allowed for active and passive scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a function to get operating class definition (including bandwidth,
channel numbers, etc.) from the operating class number and country.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add helper function that converts non-global operating classes to global
operating classes according to IEEE Std 802.11-2016, Annex E.
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
