Commit graph

658 commits

Author SHA1 Message Date
Jouni Malinen
ed87f6a80e Use a helper function for checking Extended Capabilities field
The new ieee802_11_ext_capab() and wpa_bss_ext_capab() functions can be
used to check whether a specific extended capability bit is set instead
of having to implement bit parsing separately for each need.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-01-02 18:13:19 +02:00
Jouni Malinen
e6b0898da3 Add [FST] and [UTF-8] flags to BSS command output
These flags were used in SCAN_RESULTS command output, but not BSS. Make
these consistent by adding the flags to BSS as well.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-01-02 17:58:31 +02:00
Jouke Witteveen
1f2c42cc7f Show [UTF-8] flag if the SSID is reported as UTF-8
Signed-off-by: Jouke Witteveen <j.witteveen@gmail.com>
2019-01-02 17:58:05 +02:00
Beni Lev
19677b77c3 OCE: Add RSSI based association rejection support (STA)
An AP might refuse to connect a STA if it has a low RSSI. In such case,
the AP informs the STA with the desired RSSI delta and a retry timeout.
Any subsequent association attempt with that AP (BSS) should be avoided,
unless the RSSI level improved by the desired delta or the timeout has
expired.

Defined in Wi-Fi Alliance Optimized Connectivity Experience technical
specification v1.0, section 3.14 (RSSI-based association rejection
information).

Signed-off-by: Beni Lev <beni.lev@intel.com>
2019-01-01 17:56:25 +02:00
Jouni Malinen
32bb47faa1 Update wpa_supplicant channel list on FLUSH
Try to make sure the driver channel list state is synchronized with
wpa_supplicant whenever explicitly clearing state (e.g., between hwsim
test cases).

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-01-01 15:58:46 +02:00
Jouni Malinen
948ba8c294 mka: MIB information
Provide MKA information through the wpa_supplicant control interface MIB
command.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-29 16:52:31 +02:00
Jouni Malinen
93701b4afe tests: Allow TX/RX data test to use different frame length
This is needed for MACsec test cases with a bit shorter MTU.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-12-24 23:56:25 +02:00
Jouni Malinen
0fb292c08e Add SAE to GET_CAPABILITY key_mgmt
Provide information about SAE AKM support in "GET_CAPABILITY key_mgmt"
for completeness. The "GET_CAPABILITY auth_alg" case is already
providing information about SAE support through user space SME.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-12-21 21:49:02 +02:00
Jouni Malinen
53d5de6f1d DPP: Accept DPP_CONFIGURATION_SIGN without double space before parameters
Make this command more convenient to use by not requiring two space
characters between the command and the first parameter.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-12-21 12:02:57 +02:00
Jouni Malinen
2a93ecc8ca Expose Multi-BSS STA capability through wpa_supplicant control interface
Indicate whether the driver advertises support for Multi-BSS STA
functionality with "GET_CAPABILITY multibss" (returns "MULTIBSS-STA" if
supported).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-12-20 21:30:43 +02:00
Mathy Vanhoef
5c7d35ba07 Add UNPROT_DEAUTH command for testing OCV
This new wpa_supplicant control interface command can be used to
simplify testing SA Query with OCV.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-17 15:50:12 +02:00
Jouni Malinen
d514b50265 WNM: Collocated Interference Reporting
Add support for negotiating WNM Collocated Interference Reporting. This
allows hostapd to request associated STAs to report their collocated
interference information and wpa_supplicant to process such request and
reporting. The actual values (Collocated Interference Report Elements)
are out of scope of hostapd and wpa_supplicant, i.e., external
components are expected to generated and process these.

For hostapd/AP, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration. STAs are requested to perform
reporting with "COLOC_INTF_REQ <addr> <Automatic Report Enabled> <Report
Timeout>" control interface command. The received reports are indicated
as control interface events "COLOC-INTF-REPORT <addr> <dialog token>
<hexdump of report elements>".

For wpa_supplicant/STA, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration and setting Collocated
Interference Report Elements as a hexdump with "SET coloc_intf_elems
<hexdump>" control interface command. The hexdump can contain one or
more Collocated Interference Report Elements (each including the
information element header). For additional testing purposes, received
requests are reported with "COLOC-INTF-REQ <dialog token> <automatic
report enabled> <report timeout>" control interface events and
unsolicited reports can be sent with "COLOC_INTF_REPORT <hexdump>".

This commit adds support for reporting changes in the collocated
interference (Automatic Report Enabled == 1 and partial 3), but not for
periodic reports (2 and other part of 3).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-10-30 14:07:51 +02:00
Jouni Malinen
baf4c86379 HS 2.0: Request and process OSU Providers NAI List ANQP-element
Extend wpa_supplicant to use a separate OSU_NAI information from OSU
Providers NAI List ANQP-element instead of the OSU_NAI information from
OSU Providers list ANQP-element when connecting to the shared BSS
(Single SSID) for OSU.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-10-05 20:51:51 +03:00
Bhagavathi Perumal S
d7f038ded2 wpa_supplicant: Add ieee80211ac information in STATUS
This allows user to get current operating mode of station.

Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
2018-05-04 20:18:55 +03:00
Bhagavathi Perumal S
b55c623e4c Make CENTER_FRQ1 available independently in SIGNAL_POLL
This allows user to get center frequency and find secondary channel
offset.

Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
2018-04-20 00:10:45 +03:00
Jouni Malinen
6a8a04d742 HS 2.0: Add fetching of Operator Icon Metadata ANQP-element
This extends wpa_supplicant Hotspot 2.0 ANQP routines to allow the
Operator Icon Metadata ANQP-element to be fetched with "ANQP_GET <bssid>
hs20:12". The result is available in the new hs20_operator_icon_metadata
entry in the "BSS <bssid>" output.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-17 16:40:42 +03:00
Masashi Honma
e480212765 dbus: Add FILS to global capabilities
If any of the interfaces supports FILS (and similarly for FILS-SK-PFS),
include the "fils" (and "fils_sk_pfs") capability in D-Bus information.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2018-04-02 11:56:06 +03:00
Purushottam Kushwaha
8179ae3a2a DPP: Support retrieving of configurator's private key
To retain configurator information across hostapd/wpa_supplicant
restart, private key need to be maintained to generate a valid pair of
authentication keys (connector, netaccess_key, csign) for new enrollees
in the network.

Add a DPP_CONFIGURATOR_GET_KEY control interface API through which the
private key of an existing configurator can be fetched.

Command format:
DPP_CONFIGURATOR_GET_KEY <configurator_id>

The output from this command can then be used with
"DPP_CONFIGURATOR_ADD key=<hexdump>" to create the same key again.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-16 20:55:32 +02:00
Jouni Malinen
4b07484c3d DPP: Do not include common/dpp.h without CONFIG_DPP=y
This header file pulls in an OpenSSL header file and as such, should not
be included without CONFIG_DPP=y to avoid bringing in an unnecessary
build dependency on OpenSSL header files.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-02-17 18:07:43 +02:00
vamsi krishna
d98038bb05 FILS: Driver configuration to disable/enable FILS features
The new disable_fils parameter can be used to disable FILS functionality
in the driver. This is currently removing the FILS Capability bit in
Extended Capabilities and providing a callback to the driver wrappers.
driver_nl80211.c implements this using a QCA vendor specific command for
now.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-12-15 20:52:17 +02:00
Jouni Malinen
055cd39788 tests: DPP P-256 test vectors
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-12-07 13:35:19 +02:00
Jouni Malinen
f55269753c DPP: Allow protocol key to be overridden for testing purposes
This can be used for various testing needs.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-12-05 23:53:08 +02:00
Ashok Ponnaiah
dc2f24f1b2 DPP: Fix compilation without CONFIG_TESTING_OPTIONS=y
Add CONFIG_TESTING_OPTIONS ifdef protection to couple of forgotten DPP
test parameters in wpa_supplicant ctrl_iface.

Signed-off-by: Ashok Ponnaiah <aponnaia@qti.qualcomm.com>
2017-11-27 17:30:03 +02:00
Jouni Malinen
acc555f9e6 DPP: Allow PKEX x/X and y/Y keypairs to be overridden
This is for testing purposes to allow a test vector with specific values
to be generated.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-24 01:41:50 +02:00
Jouni Malinen
2bdc47a945 DPP: Allow PKEX own/peer MAC addresses to be overridden
This is for testing purposes to allow a test vector with specific values
to be generated.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-23 23:47:52 +02:00
Jouni Malinen
95b0104a34 DPP: Retransmit DPP Authentication Response frame if it is not ACKed
This extends wpa_supplicant DPP implementation to retransmit DPP
Authentication Response frame every 10 seconds up to 5 times if the peer
does not reply with DPP Authentication Confirm frame.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-13 12:35:26 +02:00
Jouni Malinen
c1d3773967 DPP: Stop authentication exchange of DPP_STOP_LISTEN
Previously, this command stopped listen operation immediately, but if
there was an ongoing authentication exchange, a new listen operation was
started. This is not really expected behavior, so stop the
authentication exchange first with this command to avoid restarting
listen operation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-13 12:35:26 +02:00
Jouni Malinen
f97ace34cb DPP: Support multiple channels for initiating DPP Authentication
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-13 11:45:05 +02:00
Sunil Dutt
37ed3254de P2P: ACS offload for the autonomous GO
This commit introduces the ACS functionality for the autonomous GO. The
optional parameter <freq> in p2p_group_add is enhanced to carry a value
"acs" with the intention to select the channels among any supported
band. freq = 2 / 5 carry the need to select the channels only in the
respective bands 2.4 / 5 GHz. This functionality is on top of the host
driver's capability to offload ACS, which is advertized through
WPA_DRIVER_FLAGS_ACS_OFFLOAD.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-03 21:47:32 +02:00
Jouni Malinen
b7dddab7be DPP: Allow testing override values to be cleared
This allows wpa_supplicant dpp_config_obj_override,
dpp_discovery_override, and dpp_groups_override parameters to be cleared
by setting them to a zero-length value.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-29 12:23:34 +02:00
Jouni Malinen
60239f60a6 DPP: Protocol testing framework
Add a generic mechanism for configuring the DPP implementation to behave
in particular different (mostly incorrect) ways for protocol testing
purposes. The new dpp_test parameter can be set to a non-zero integer to
indicate a specific behavior. This is only available in
CONFIG_TESTING_OPTIONS=y builds.

This commit include cases for an extra attribute being added after the
Wrapped Data attribute and Initiator/Responder capabilities having an
unexpected zero capability.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-22 17:21:57 +03:00
Jouni Malinen
daa4096084 Allow last (Re)Association Request frame to be replayed for testing
The new wpa_supplicant RESEND_ASSOC command can be used to request the
last (Re)Association Request frame to be sent to the AP to test FT
protocol behavior.

This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 17:47:24 +03:00
Jouni Malinen
751f5b2933 Allow EAPOL-Key Request to be sent through control interface
The new wpa_supplicant "KEY_REQUEST <error=0/1> <pairwise=0/1>" command
can be used to request an EAPOL-Key Request frame to be sent to the AP.

This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 17:47:24 +03:00
Jouni Malinen
bb06748f45 Make last received ANonce available through control interface
This makes it easier to debug 4-way handshake implementation issues
without having to use a sniffer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 17:47:24 +03:00
Jouni Malinen
16579769ff Add testing functionality for resetting PN/IPN for configured keys
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").

This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 17:43:10 +03:00
Jouni Malinen
a0bf1b68c0 Remove all PeerKey functionality
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.

This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.

Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 02:03:47 +03:00
Jouni Malinen
e8b9649012 OWE: Transition mode support on station side
Add support for using the OWE Transition Mode element to determine the
hidden SSID for an OWE BSS that is used in transition mode.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-08 17:12:35 +03:00
vamsi krishna
e37cea308e OCE: Update default scan IEs when OCE is enabled/disabled
Update the default scan IEs when OCE is enabled/disabled to the
driver/firmware, so that the correct IEs will be sent out by the
driver/firmware in Probe Request frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-01 18:47:02 +03:00
Jouni Malinen
a0f19e9c74 SAE: Allow commit fields to be overridden for testing purposes (STA)
The new "SET sae_commit_override <hexdump>" control interface command
can be used to force wpa_supplicant to override SAE commit message
fields for testing purposes. This is included only in
CONFIG_TESTING_OPTIONS=y builds.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-04 13:32:03 +03:00
Jouni Malinen
a4bf007877 DPP: Remove devices object from the connector
This was removed from the draft DPP tech spec, so remove it from the
implementation as well.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-08-22 23:46:27 +03:00
Ashwini Patil
332aadb8a2 STA: Add OCE capability indication attribute
Add OCE capability indication attribute in Probe Request and
(Re)Association Request frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-14 21:19:53 +03:00
Andrei Otcheretianski
d02e4c8ac8 P2P: Clear get_pref_freq_list_override on P2P Device
Clear the get_pref_freq_list_override in p2p_ctrl_flush(). This fixes
the case when a dedicated P2P device interface is used.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2017-07-08 16:06:28 +03:00
Vidyullatha Kanchanapally
fe3e0bac1f FILS: Advertize FILS capability based on driver capability
Add changes to control interface command get_capability to advertize
FILS capability, FILS AKMs suites, and FILS Authentication algorithms
based on the driver capabilities.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-07 13:39:05 +03:00
Ashwini Patil
267fc0dd33 Add wpa_supplicant ctrl iface support to scan for a specific BSSID
Add support to scan for a specific BSSID through the wpa_supplicant
control interface.

Usage: wpa_cli scan bssid=ab:bc:cd🇩🇪ef:12

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-05 02:02:32 +03:00
Jouni Malinen
f522bb2377 DPP: Add DPP_CONFIGURATOR_SIGN to generate own connector
The DPP Configurator can use this new command to generate its own signed
connector for the network that it manages.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-04 17:48:44 +03:00
Jouni Malinen
b65b22d60a DPP: Configurator parameters in responder role
This allows wpa_supplicant to be configured to act as the configurator
in the case where a peer device initiates DPP Authentication.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-03 13:03:34 +03:00
Jouni Malinen
500ed7f006 DPP: PKEX bootstrapping
This implements genric PKEX functionality in src/common/dpp.c and glue
code to use this in wpa_supplicant (i.e, hostapd DPP implementation does
not yet support PKEX).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-02 09:35:00 +03:00
Jouni Malinen
6a7182a9c3 DPP: Add DPP_BOOTSTRAP_INFO command
This can be used to fetch parsed details on bootstrapping information.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-22 14:51:21 +03:00
Jouni Malinen
567da5bbd0 DPP: Add new AKM
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
461d39af40 DPP: Configuration exchange
This adds support for DPP Configuration Protocol using GAS. Full
generation and processing of the configuration object is not included in
this commit.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:15 +03:00