Commit graph

1437 commits

Author SHA1 Message Date
윤민홍
3b655312d4 P2P: Send D-Bus ServiceDiscoveryRequest signal for external SD processing
wpas_notify_p2p_sd_request() needs to be called when
p2p_sd_over_ctrl_iface is set to provide SD events over D-Bus similarly
to the ctrl_iface events.
2011-12-22 00:34:29 +02:00
Jouni Malinen
9b6f44cb63 Process EVENT_SCHED_SCAN_STOPPED partially if interface is disabled
The internal sched_scanning state needs to be cleared on this event
even if the events happen to get ordered in a way that the interface
gets disabled just prior to EVENT_SCHED_SCAN_STOPPED event.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-21 13:36:58 +02:00
Jouni Malinen
4551dd9060 Ignore disassociation event in wpa_supplicant AP mode
If the driver was associated in station mode just before the AP mode was
started, the station mode disassociation event may end up getting
delivered to wpa_supplicant only after the AP mode has been started.
This can result in unexpected attempt to reassociate back to the network
that was previously used in station mode. Avoid this by ignoring the
disassociation event.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-21 13:36:13 +02:00
Jouni Malinen
72d48a80ec P2P: Fix GO start on interface that has active station connection
The active station connection triggered wpa_supplicant AP mode startup
to try to update Beacon IEs before the AP mode was properly initialized
and that resulted in NULL pointer dereference in driver_nl80211.c. Fix
this by skipping the IE update before the AP mode is initialized.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-21 13:34:25 +02:00
Neeraj Kumar Garg
653c4893be Add AP-STA-CONNECTED and DISCONNECTED events to wpa_cli -a
Signed-hostap: Neeraj Kumar Garg <neerajkg@broadcom.com>
2011-12-20 01:07:42 +02:00
Jouni Malinen
c81066153c P2P: Use hardcoded idle timeout of 10 seconds in P2P client role
The p2p_group_idle configuration parameter is much more useful for
GO role, so use a separate hardcoded value of 10 seconds in P2P
client role. In practice, this means that the P2P client role will
automatically tear down the group when the GO tears down the group.

The 10 second timeout is enough to recover from temporary disconnections
without unnecessary tearing down the group if the GO is still present
and allows the client to connect.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 22:21:22 +02:00
Jouni Malinen
4c2c675173 P2P: Fix disconnect event not to increase idle timeout
When P2P client is processing a disconnection event, make sure the P2P
idle timeout does not get increased, i.e., set a new timeout only if no
timeout is in use. wpa_state changes between DISCONNECTED and SCANNING
can generate multiple calls to wpas_p2p_notif_disconnect() and
previously this was enough to force the idle timeout never hit in
practice when in P2P client role.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 22:18:42 +02:00
Jouni Malinen
74781dfc7b Lower RX_MGMT driver event debug level for Beacon frames
This event can be very frequent in AP mode when Beacon frames from
neighboring BSSes are delivered to user space. Drop the debug
message priority from DEBUG to EXCESSIVE for Beacon frames.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 21:48:25 +02:00
Jouni Malinen
1ef2f7ffcf P2P: Fix Provision Discovery channel for some join-GO cases
The Provision Discovery Request needs to be sent on the operating
channel of the GO and as such, the frequency from the BSS table
(scan results) need to override the frequency in the P2P peer
table that could be based on the Listen channel of the GO.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 17:21:25 +02:00
Gustavo Sverzut Barbieri
19030351b9 wpa_supplicant/dbus AP: Add support for WPS Internal Registrar
When in AP mode, wpa_supplicant is now enabling WPS (only Internal
Registrar). WPS.Start() call can be used to initiate WPS negotiation
similarly to how this is done in station mode.

This was done to ctrl_iface by Jouni Malinen on April 21, 2009 (commit
3ec97afe57)

Signed-hostap: Gustavo Sverzut Barbieri <barbieri@profusion.mobi>
2011-12-18 17:06:31 +02:00
Reinette Chatre
e5a359cf7e P2P: Make GO negotiation peer and group information available over D-Bus
The GO negotiation response is very cryptic at the moment. For a success
message we only know on which interface the negotiation succeeded, not
which peer. For a failure we know the interface also and a status code
(number).

It will be very useful for clients to know upon receipt of such a message
which peer the negotiation occurred with.

Now that the peer information is available and the API is changed
already, the function composing the D-Bus message might as well include
all GO negotiation information. This is done with a dict to make things
easier on clients if this result information changes down the line.

Signed-hostap: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2011-12-18 16:52:33 +02:00
Jouni Malinen
90b8fc8f4e Fix CONFIG_NO_SCAN_PROCESSING=y build with ctrl_iface
Need to remove ROAM command processing since the needed functionality
for it gets removed with CONFIG_NO_SCAN_PROCESSING=y.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-17 18:07:58 +02:00
Antonio Quartulli
b58bcbb2ef ctrl_iface: Check for IEEE8021X_EAPOL definition
The whole wpa_supplicant_ctrl_iface_ctrl_rsp_handle() function operates
on the ssid->eap field which exists only if IEEE8021X_EAPOL has been
defined. Therefore the whole function body needs to be enclosed within
an #ifdef/endif block.

Signed-hostap: Antonio Quartulli <ordex@autistici.org>
2011-12-17 18:04:50 +02:00
Johannes Berg
457a126e29 IBSS: fix RSN key initialisation
Antonio reported that RSN IBSS failed to work.
We traced it down to a GTK failure, and he then
bisected it to commit bdffdc5ddb:
"AP: Reorder WPA/Beacon initialization".

The reason this commit broke it is that the state
machine's GInit variable is never set to false as
wpa_init_keys() never gets called, and thus new
keys are generated every time the state machine
executes.

Fix this by calling wpa_init_keys() when the new
group has been initialised.

Reported-by: Antonio Quartulli <ordex@autistici.org>
Tested-by: Antonio Quartulli <ordex@autistici.org>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2011-12-11 19:57:50 +02:00
Jouni Malinen
d9d87c3357 Disassociate when starting WPS search
Previously, the WPS scans could have been done in associated state if we
happened to be associated when the request to use WPS was received. This
can slow down scanning and end up in unexpected state if no WPS
association is tried. Avoid these issues by disconnecting when WPS
search is started.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:30:47 +02:00
Jouni Malinen
5506d18418 Fix compiler warning with CONFIG_NO_STDOUT_DEBUG=y
Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:19:24 +02:00
Jouni Malinen
5928411e91 Fix compiler warning with CONFIG_NO_SCAN_PROCESSING=y
Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:14:09 +02:00
Jouni Malinen
76202aed23 Fix compiler warning with CONFIG_NO_STDOUT_DEBUG=y
Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:13:51 +02:00
Jouni Malinen
7165c5dc1f P2P: Fix 32-bit compiler warnings on service discovery reference
Convert core wpa_supplicant code to use u64 instead of void * for the
P2P service discovery reference. Use uintptr_t in type casts in
p2p_supplicant.c to handle the conversion without warnings.

Note: This needs to be revisited for 128-bit CPU where sizeof(void *)
could be larger than sizeof(u64).

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:06:34 +02:00
Jouni Malinen
e3a0706b47 P2P: Fix Provision Discovery name in debug messages
Some debug messages used incorrect name for Provision Discovery.
Replace "Provisioning Discovery" with "Provision Discovery".

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 17:36:38 +02:00
Vitaly Wool
c3daaf3325 Skip WPS PBC overlap detection if P2P address is the same
WPS overlap detection can detect false overlap if a P2P peer
changes UUID while authentication is ongoing. Changing UUID
is of course wrong but this is what some popular devices do
so we need to work around it in order to keep compatibility
with these devices. There already is a mechanism in WPS
registrar to skip overlap detection if P2P addresses of two
sessions match but it wasn't really triggered because the
address wasn't filled in in the caller function.

Let's fill in this address and also clean up WPS PBC sessions
on WSC process completion if UUID was changed.

Signed-hostap: Vitaly Wool<vitalywool@gmail.com>
2011-12-11 12:03:18 +02:00
Arik Nemtsov
4f73d88afa Maintain internal copy of Probe Response offload capabilities
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2011-12-10 21:11:32 +02:00
Jouni Malinen
502618f7c1 P2P: Clean up group formation on network block removal
If a P2P group network block is removed for any reason (e.g., wps_cancel
command) while the interface is in group formation, remove the group
formation timeout and indicate failure immediately. Previously, this
type of operations could end up leaving the timeout running and result
in somewhat unexpected group formation failure events later.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-10 12:56:42 +02:00
Jouni Malinen
c3f4278445 P2P: Add group ifname to P2P-PROV-DISC-* events
If Provision Discovery Request is sent for GO role (i.e., P2P Group ID
attribute is included), add the group interface name to the control
interface event on the GO. This makes it easier to figure out which
ctrl_iface needs to be used for wps_pbc/wps_pin command to authorize
the joining P2P client.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-06 21:57:17 +02:00
Jithu Jance
ec437d9e74 P2P: Skip duplicated provision discovery on join
If p2p_prov_disc join command is used prior to p2p_connect join,
skip the duplicated provision discovery exchange.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2011-12-06 21:44:57 +02:00
Jithu Jance
8c5f730983 P2P: Add optional "join" argument for p2p_prov_disc command
This can be used to request Provision Discovery Request to be sent
for the purpose of joining a running group, e.g., to request the GO
to display a PIN that we can then use with p2p_connect join command.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2011-12-06 21:28:02 +02:00
Jouni Malinen
61ff2c8080 Remove documentation for label option in p2p_connect
P2P use cases do not allow use of Label config method and the earlier
code for this has already been removed, but this documentation was not
updated at the same time.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-06 21:13:54 +02:00
Jouni Malinen
14115a1089 SME: Fix processing of Authentication timeout
The wpa_state needs to be dropped back to DISCONNECTED to allow scan
results to trigger a new authentication attempt.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-04 22:27:48 +02:00
Jouni Malinen
d00821e913 Try to reconnect to the same BSS on recoverable disconnection
If the AP disconnects us with a reason code that indicates that it has
dropped the association, but could allow us to connect again, try to
reconnect to the same BSS without going through the full scan. This can
save quite a bit of time in some common use cases, e.g., when inactivity
timeout is used on the AP (and especially, when waking up from suspend
which has likely triggered some timeout on the AP).

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-04 21:57:14 +02:00
Jouni Malinen
ed57c5907e SME: Fix processing of Authentication request failure
The wpa_state needs to be dropped back to DISCONNECTED to allow scan
results to trigger a new authentication attempt. In addition, we can use
wpas_connection_failed() instead of requesting a scan after a fixed time
to make this error case more consistent with other similar error paths
in sme.c.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-04 21:04:24 +02:00
Jouni Malinen
bfba8deb8b Update internal MAC address on EVENT_INTERFACE_ENABLED events
This allows the MAC address of the interface to be changed when the
interface is set down even if the interface does not get completed
removed and re-added.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-03 13:20:40 +02:00
Johan Hedlund
f98eb880eb Update RSN supplicant MAC address on driver reinitialization
I have a test case where I remove and insert another network adapter
between two connections to AP. The interface get the same interface name
but switches macadresses between the connections. When running WPA2 I
got a failure in EAPOL negotiation and found out that the reason for
this was that the supplicant did not update the MAC address in the
correct place.
2011-12-03 13:02:57 +02:00
Szymon Bigos
9337e876ab Fix generated WPS PIN values to use zero-padding
The dynamically generated PINs are supposed to have 8 digits, but
some PIN generatation cases were not zero-padding these properly.
2011-12-02 23:04:39 +02:00
Jouni Malinen
47662f4017 Add example WPS AP mode UI for wpa_supplicant
This script shows some minimal WPS user interface requirements for
mobile AP support with wpa_supplicant.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-01 22:14:07 +02:00
Jouni Malinen
0bc134683e wpa_supplicant AP: Allows passphrase to be fetched
"wpa_cli status wps" can now be used to fetch the WPA2-Personal
passphrase from AP mode operation with wpa_supplicant to make it
easier to meet WPS requirements for legacy STA support.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-01 22:12:03 +02:00
Jouni Malinen
c0f83f3104 WPS: Disable WPS(v2) in WPA/TKIP-only configuration
When using wpa_supplicant AP mode, WPS support is enabled by default for
WPA/WPA2-Personal. Change this to enforce the WPS2 rules on not allowing
WPS to be used with WPA/TKIP-only configuration (i.e., at minimum, mixed
mode with WPA/TKIP and WPA2/CCMP has to be used for WPS to be enabled).

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-01 21:46:19 +02:00
Jouni Malinen
56d24b4ee0 Call wpas_connection_failed() only if actually trying to connect
A disconnection event from the driver may end up getting delivered at a
time when wpa_supplicant is not even trying to connect (e.g., during a
scan that was already started after WPS provisioning step). In such a
case, there is not much point calling wpas_connection_failed() and
skipping this avoids confusing attempts of re-starting scanning while
the previous scan is still in progress.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-01 18:22:56 +02:00
Jouni Malinen
f7da5a9ef4 Make reconnect-on-disassoc debug prints somewhat more helpful
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-01 18:22:10 +02:00
Jouni Malinen
a9e02d593d P2P: Clear show_group_started on GO start
The show_group_started variable could be left to 1 based on an earlier
failed attempt to start P2P client operation. This can result in
unexpected P2P-GROUP-STARTED event when a GO is started without group
formation (e.g., re-invoke a persistent group or start an autonomous
GO). Avoid this by explicitly clearing show_group_start when setting up
the GO.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-01 10:49:26 +02:00
Arik Nemtsov
79b8c60f81 Set ht_capab from based on driver capabilities when in P2P GO mode
Set the HT capabilities of a P2P GO according to the wiphy supported
ones. Mask-in a white-list of HT capabilities that won't cause problems
for non-supporting stations.

Signed-hostap: Arik Nemtsov <arik@wizery.com>
2011-11-29 23:45:07 +02:00
Jouni Malinen
ea5bae4731 Increase min sched_scan interval from 2 to 10 seconds
Trying to run sched_scan round every two seconds by defaults sounds way
too frequent since dualband cards are unlikely to be able to complete
the full scan cycle in two seconds. For now, set the hardcoded value to
10 seconds to make this somewhat more reasonable.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-29 20:05:58 +02:00
Dmitry Shmidt
d70b945d4d Fix pno_start() to initialize SSID list properly
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2011-11-29 12:56:32 +02:00
Jouni Malinen
0b7a25c00f Use normal scan before sched_scan if that can speed up connection
When normal scan can speed up operations, use that for the first three
scan runs before starting the sched_scan to allow user space sleep more.
We do this only if the normal scan has functionality that is suitable
for this or if the sched_scan does not have better support for multiple
SSIDs.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 18:36:36 +02:00
Jouni Malinen
76a5249e52 Add broadcast SSID for sched_scan for scan_ssid=0 networks
Previously, only networks with scan_ssid=1 were included in sched_scan.
This needs to behave similarly to the normal scan where broadcast SSID
is used to find networks that are not scanned for with a specific SSID.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 18:12:38 +02:00
Jouni Malinen
5edddf4175 Use common code for disabled network case in sched_scan
There is no need to implement two copies of the iteration code here.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 18:09:37 +02:00
Jouni Malinen
86b47aaf36 Drop sched_scan filter if not enough match sets supported
Instead of including only a single SSID in the sched_scan request if
the driver does not support match sets, just drop the SSID filter and
configure more SSIDs up to the sched_scan limit.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 17:52:36 +02:00
Jouni Malinen
a8cb5a8897 Make sched_scan debug clearer on timeout use
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 17:52:02 +02:00
Jouni Malinen
6ad9c91100 Stop sched_scan on DISCONNECT command
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 16:35:30 +02:00
Jouni Malinen
b5c6831201 Add preferred network offload (PNO) functionality
"SET pno <1/0>" ctrl_iface command can now be used to start/stop PNO
with sched_scan driver commands. This will request offloading of
scanning to find any of the enabled networks in the configuration.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 16:32:44 +02:00
Jouni Malinen
7c6a266ced Fix sched_scan filter_ssids setting for no filters case
The filter_ssids pointer needs to be set to NULL if no SSID filters
are set to avoid filtering out all scan results.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 15:19:41 +02:00