If an implicit TDLS set up request is obtained on an existing link or an
to be established link, the previous link was not removed. This commit
disables the existing link on a new set up request. Also,
wpa_tdls_reneg() function was invoking wpa_tdls_start() on an already
existing peer for the case of internal setup, which is incorrect. Thus
the invocation of wpa_tdls_start() is removed in wpa_tdls_reneg() and
also this function is renamed to wps_tdls_remove() as it does not
renegotiation rather shall remove the link (if any) for the case of
external setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 50178335bf introduced a regression
for P2P-GROUP-STARTED event indication during p2p_connect-join when
using a separate P2P group interface. wpa_s->global->p2p_group_formation
was already set in that case to point to the group interface and this
commit changed this to point to incorrect interface. Fix this by setting
p2p_group_formation here only in case a separate group interface is not
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 59ff6653aa fixed this issue for
'removing a network', and we also need to take care of 'removing all
networks'.
Signed-hostap: Jaewan Kim <jaewan at google.com>
Addition of wpa_supplicant_fast_associate() made it unnecessary to call
wpas_select_network_from_last_scan() directly from other files.
Signed-hostap: Jouni Malinen <j@w1.fi>
If scan results are available when we perform a SelectNetwork, use
them to make an associate decision. This can save an entire scan
interval-worth of time in situations where something external to
wpa_supplicant (like a connection manager) has just previously
requested a scan before calling SelectNetwork.
Signed-hostap: Paul Stewart <pstew@chromium.org>
When the scan interval is changed the new interval is effective
after the old interval timer fires off one last time. This can cause
an unacceptable long delay when updating the interval.
Change this behaviour to use MIN(left of old interval, new interval)
for the scan interval following the interval change.
Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
The link was not disabled for the case of implicit trigger from the
driver unlike in the case of explicit trigger fromc ctrl_iface. Make the
tear down sequences match in these cases by adding the TDLS_DISABLE_LINK
tdls_oper to the driver when processing the TDLS_REQUEST_TEARDOWN event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Signal the start of EAP authentication as well as when additional
credentials are required to complete.
Signed-hostap: Paul Stewart <pstew@chromium.org>
Most of the variables are not needed anymore once the SAE instance
has entered Accepted state. Free these to save memory.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows FFC groups to be used with SAE. Though, these groups are not
included in the default sae_groups value based on what is available
since the FFC groups have the additional requirement of using a safe
prime with the current implementation (or specification of the group
order).
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though this command is very unlikely to fail, in theory, it could
and the WPS connection would fail in such a case. Return more clearer
failure indication in such a case without even trying to start
reassociation.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new "sae_group=<id>" line will be included in the ctrl_iface STATUS
output if SAE was used for the association.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd.conf sae_groups parameter can now be used to limit the set of
groups that the AP allows for SAE. Similarly, sae_groups parameter is
wpa_supplicant.conf can be used to set the preferred order of groups. By
default, all implemented groups are enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd can now be configured to use anti-clogging mechanism based on
the new sae_anti_clogging_threshold parameter (which is
dot11RSNASAEAntiCloggingThreshold in the standard). The token is
generated using a temporary key and the peer station's MAC address.
wpa_supplicant will re-try SAE authentication with the token included if
commit message is rejected with a token request.
Signed-hostap: Jouni Malinen <j@w1.fi>
The enum values for struct sae_data::state now match the protocol
instance states as defined in IEEE Std 802.11-2012, 11.3.8.2.2
Signed-hostap: Jouni Malinen <j@w1.fi>
The -N and -C command line parameters can be used to add arbitrary
RADIUS attributes to the messages. However, these were truncated to
about 128 bytes when the actually message was constructed. Fix this by
using larger buffers to allow the maximum attribute length (253 octets
of payload) to be used. [Bug 458]
Signed-hostap: Jouni Malinen <j@w1.fi>
The sizeof(ptr) use here was not correct and resulted in too small
memory block getting allocated for the -N command line argument.
Signed-hostap: Jouni Malinen <j@w1.fi>
In case of wpa_supplicant IBSS and AP modes after we will call wpa_cli
save command we should also save configured frequency. In other case
after wpa_supplicant restart we have frequency = 0 and AP start will
fail.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The GAS query compilation callback may happen after the wpa_supplicant
process has been requested to terminate. Avoid scheduling a new eloop
timeout for a scan in such a case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that the other BSS has actually received some valid ANQP
information before sharing the results from it. This fixes potential
issues with cases where some of the APs with the same HESSID has invalid
ANQP configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver rejected any of the offchannel Action frame TX requests,
the previous implementation terminated ANQP fetch process. While the
driver should not really reject the request normally, it is possible
that a request gets rejected for some reason. Allow the fetch process to
continue with the next AP in such case to avoid breaking networking
selection. This could result, e.g., in auto_interworking=1 process
failing to connect if any the driver rejects requests to any of the APs
in the scan result even if some other APs provided suitable information.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This was used to select between "(auth)" and "(reauth)" in
CTRL-EVENT-CONNECTED events. However, the variable was not cleared
anywhere else apart from the AP deinit case. As such, it did not really
provide correct information and is not really of much use even with
proper clearing added. As such, it is cleaner to just get rid of this
altogether.
Signed-hostap: Jouni Malinen <j@w1.fi>
