The static function is_chanwidth160_supported() is called only within
CONFIG_P2P block so the function itself needs to have matching condition
for build.
Fixes: ed24bad1d9 ("AP: Check driver support while auto-selecting bandwidth for AP/P2P GO")
Signed-off-by: Jouni Malinen <j@w1.fi>
Use more accurate INTERWORKING_EXCLUDED for this. The actual event
prefix is not changed to remains compatible with external components
using this control interface event message.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a more specific name for the control interface command used for
managing the list of BSSIDs that are temporarily ignored.
Signed-off-by: Jouni Malinen <j@w1.fi>
Rename the network profile parameters bssid_blacklist and
bssid_whitelist to bssid_ignore and bssid_accept to use more specific
names for the configuration of which BSSs are ignored/accepted during
BSS selection. The old parameter names are maintained as aliases for the
new names to avoid breaking compatibility with previously used
configurations.
Signed-off-by: Jouni Malinen <j@w1.fi>
This previously reserved bit is now used in FTM to help select the
appropriate replay counter. Silence the warning about use of a reserved
bit for this. wlantest does not yet support the actual replay counter
processing for FTM.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use the TKs from the PTK file (-T command line argument) to try to
decrypt encrypted Management frames if no BSS/STA key can be found based
on addresses.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add test cases that check preCAC, which is available for EU regulatory
domain. Also confirm that preCAC is not used for US.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
For EU, where preCAC is allowed, we should allow switch to DFS available
channels, instead of restarting BSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Return FAIL for couple of the operations that were previously ignoring
invalid addresses without reporting errors.
Signed-off-by: Masafumi Utsugi <mutsugi@allied-telesis.co.jp>
hostapd_disassoc_accept_mac() was called after a new accept MAC address
was added (ACCEPT_ACL ADD_MAC), but this function should have been
called after an accept MAC address was removed and accept MAC list was
cleared to disconnect a STA which is not listed in the update accept MAC
address list. Fix this by moving the call to places where a connected
STA can actually end up losing its previously present accept entry.
Signed-off-by: Masafumi Utsugi <mutsugi@allied-telesis.co.jp>
Add option to:
- add a new AP on the same phy that the backhaul-sta uses
- run CSA from the parent
Adding a new AP (backhaul/fronthaul) on the same phy we have for
backhaul-sta is closer to the real repeater implementation.
Add a test case for that and run CSA.
This is a common problem when we have on the same phy:
- connected backhaul STA
- we started fronthaul/backhaul AP
- we receive (from parent) CSA on the STA interface
This is multi_ap_wps_shared_apdev_csa test case, which fails today with
both mac80211_hwsim and ath9k. To avoid always failing test cases,
ignore this failure for now. Full validation can be enabled once the
issue behind this is fixed.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Pass the backhaul parameters as a parameter. This is in preparation for
channel switch test for Multi AP.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Since a running hostapd is not necessarily using the settings that are
in the configuration file (if they were changed at runtime, or the file
was changed but not reloaded, etc.), being able to get their value at
runtime can be useful (to know if they have to be updated for example).
If multi_ap is set, also print the SSID and passphrase (or PSK).
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
This test first configure hostapd with an initial SSID
('test-wpa2-psk-start'). Then a new SSID is configured
('test-wpa2-psk-new') using SET and RELOAD. Next, a station is
associated using WPS, and the test verifies that the new SSID was served
to the station.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
When new credentials are configured and hostapd is reconfigured using
SIGHUP (or RELOAD on the ctrl_iface), also update the WPS credentials.
Before these changes, when WPS is triggered the Registar always serves
the credentials that were configured when hostapd started.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
This is in preparation of larger changes in hostapd_update_wps() to keep
the commits more readable.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
For Android the default value of 5 seconds is usually too short for
scan results from last scan initiated from settings app to be
considered for fast-associate. Make the fast-associate timer value
configurable so that a suitable value can be set based on a systems
regular scan interval.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sony.com>
wpa_supplicant does not send a D-Bus notification of the BSS frequency
change when a CSA happens. Sending a PropertyChanged signal with the
updated frequency will notify the network manager quickly, instead of
waiting for the next scan results.
Signed-off-by: Arowa Suliman <arowa@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
cfg80211 may ignore user hints while there are active COUNTRY_IE hints,
thus at some timings it may ignore the country setting back to world
domain. Fix it by making sure the country is set only after all the
interfaces are stopped. In addition, call a more robust
clear_regdom_dev() function.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Some time ago it was found some drivers are setting their hw/ucode RX
filters restrictively enough to prevent broadcast DPP Action frames from
being received at upper layers in the stack.
A set of patches was introduced to the kernel and
ath9k driver as well as wpa_supplicant, e.g.,
a39e9af90 ("nl80211: DPP listen mode callback")
4d2ec436e ("DPP: Add driver operation for enabling/disabling listen mode")
However, the hostapd code itself was not calling the new multicast
registration. As such the AP side of things wasn't working as expected
in some scenarios. I've found this while trying to get ath9k working as
an AP Responder/Configurator.
The problem wasn't seen on, e.g., mac80211 hwsim driver.
Extend the wpa_supplicant mechanism to work with hostapd as well.
Signed-off-by: Michal Kazior <michal@plume.com>
Test that if notify_mgmt_frames is enabled and a station connects we do
get AP-MGMT-FRAME-RECEIVED, and that it includes an Authentication
frame.
Also test that if notify_mgmt_frames is disabled, no Management frame is
sent on ctrl_iface when a station connects.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
In some contexts (e.g., Multi-AP) it can be useful to have access to
some of the management frames in upper layers (e.g., to be able to
process the content of association requests externally).
Add 'notify_mgmt_frames'. When enabled, it will notify the ctrl_iface
when a management frame arrives using the AP-MGMT-FRAME-RECEIVED event
message.
Note that to avoid completely flooding the ctrl_iface, not all
management frames are included (e.g., Beacon and Probe Request frames
are excluded).
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
Add option 2 to the p2p_device_random_mac_addr configuration option to
support device drivers which use by default random MAC adresses when
creating a new P2P Device interface (for instance, the BCM2711 80211
wireless device driver included in Raspberry Pi 4 Model B). In such
case, this option allows to create the P2P Device interface correctly
when using P2P permanent groups, enabling wpa_supplicant to reuse the
same MAC address when re-invoking a P2P permanent group.
update_config=1 is required.
Signed-off-by: Ircama <amacri@tiscali.it>
Messages such as RTM_IFNFO or RTM_IFANNOUNCE could have been lost.
As such, sync the state of our internal driver to the state of the
system interfaces as reports by getifaddrs(2).
This change requires the routing socket be placed in non-blocking
mode. While here, set the routing and inet sockets to close on exec.
BSDs that support SO_RERROR include NetBSD and DragonFly.
There is a review underway to add this to FreeBSD.
Signed-off-by: Roy Marples <roy@marples.name>
When the AP advertised RSNE, RSNXE, and WPA IE, hostapd incorrectly
removed the RSNE in the EAPOL-Key msg 3/4 if the STA associates with
WPA, leaving only RSNXE instead of WPA IE. WPA STA fails to connect to
such AP as the WPA IE is missing.
Since RSNXE is not really used in non-RSN connection, just remove it
here with RSNE.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This is needed to avoid the corner case of local RSNXE aware station
being configured to behave as WPA(v1)-only STA when the AP might not
include RSNXE in EAPOL-Key msg 3/4.
Signed-off-by: Jouni Malinen <j@w1.fi>
The P2P group may be originally formed on UNII-3, so disabling UNII-1
and UNII-2 will not result in a channel switch failing the test.
Fix this by setting 44 as a preferred channel.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The test configures ft_r0_key_lifetime parameter, however ft_params
already contain the r0_key_lifetime. Since both options are accepted by
hostapd and set the same field, one of them gets overwritten.
As the dictionary enumeration order is not guaranteed in python, the
test may sporadically fail.
Fix that by explicitely removing the unneeded parameter.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Old gcc versions complain about signed/unsigned comparison in
dpp_rx_gas_resp(). Hide it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Use the helper instead of open-coding the check. Since the
helper doesn't handle a NULL BSS, keep that extra check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no point in attempting to configure frame filters on
a P2P-Devices that doesn't even have a netdev (nor passes any
data traffic), that just results in error messages. Skip it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wpa_bss structure's last element is an empty array. The forgotten
code here assumed that the array of IEs was contiguous to the wpa_bss
structure. This is not always the case anymore. Update this missed case
to use the new wpa_bss_ie_ptr() wrapper to send the correct array of IEs
over DBus.
Fixes: be7ee264f6 ("BSS: Use wrapper function for getting a pointer to the IE buffer")
Signed-off-by: Brad Kemp <brad at beechwoods.com>
Add HE as an accepted option ("he") in the CHAN_SWITCH command similarly
to the way VHT is addressed.
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
