Commit graph

344 commits

Author SHA1 Message Date
Jouni Malinen
4d9fb08d23 WPS: Clear known_wps_freq in addition to after_wps
Both of these variables can result in optimized WPS scans, so better
clear these more consistently to avoid unexpected single-channel scans.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-27 12:56:56 +02:00
Jouni Malinen
a2a535f897 Remove unnecessary wpa_s->conf checks
wpa_s->conf cannot be NULL because wpa_supplicant_init_iface() would not
allow wpa_supplicant_add_iface() to return wpa_s instance in such state.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-26 15:55:52 +03:00
Naresh Jayaram
07041c6f99 eap_proxy: Confirm eap_proxy initialization before reading SIM info
Trying to access the SIM card details without checking if the eap_proxy
layer has been initialized can results in a crash. Address this by
sending the request for the IMSI through eapol_supp_sm.c which can
verify that eap_proxy has been initialized.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-23 20:51:39 +03:00
Jouni Malinen
d259249762 Fix ENABLE_NETWORK not to reconnect in disconnected state
DISCONNECT followed by ENABLE_NETWORK ended up starting a scan for a new
connection due to wpa_supplicant_enable_one_network() setting
wpa_s->reassociate = 1. This was done regardless of wpa_s->disconnected
being 1 which should imply that wpa_supplicant should not try to connect
before asked explicitly with REASSOCIATE or RECONNECT.

Fix this by making ENABLE_NETWORK setting of reassociate = 1 and
starting of scans for connection conditional on wpa_s->disconnected ==
0. This will make ENABLE_NETWORK trigger a connection only if
wpa_supplicant is already in a state where it would try to connect if
there are any enabled networks.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-23 12:09:46 +03:00
Jouni Malinen
af8a827b90 Make frequency range list routines more general
This allows the frequency range list implementation to be shared for
other purposes.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-23 00:44:07 +03:00
Kyeyoon Park
c377514337 GAS: Delay GAS query Tx while scanning/connecting
Offchannel operations needed for a GAS query can conflict with ongoing
scan/connection progress, so delay GAS queries if such an operation is
in progress on the current interface or any virtual interface sharing
the same radio.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-21 13:15:45 +03:00
Jouni Malinen
a5d44ac083 EAP peer: Add framework for external SIM/USIM processing
The new configuration parameter external_sim=<0/1> can now be used to
configure wpa_supplicant to use external SIM/USIM processing (e.g., GSM
authentication for EAP-SIM or UMTS authentication for EAP-AKA). The
requests and responses for such operations are sent over the ctrl_iface
CTRL-REQ-SIM and CTRL-RSP-SIM commands similarly to the existing
password query mechanism.

Changes to the EAP methods to use this new mechanism will be added in
separate commits.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-20 13:12:04 +03:00
Jouni Malinen
56f5af489c Interworking: Add support for QoS Mapping functionality for the STA
Indicate support for QoS Mapping and configure driver to update the QoS
Map if QoS Map Set elements is received from the AP either in
(Re)Association Response or QoS Map Configure frame.

This commit adds support for receiving the frames with nl80211 drivers,
but the actual QoS Map configuration command is still missing.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-18 14:13:45 +03:00
Arif Hussain
8b3b803ab9 Include Extended Capabilities element based on scan results
Add Extended Capabilities element to association request only if the AP
included this element in Beacon/Probe Response frames. This is a
workaround to address interoperability issues with some older APs that
do not seem to be able to handle Extended Capabilities element in
(Re)Association Request frames.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-02 08:09:05 -07:00
Jouni Malinen
20625e9753 P2P: Remove P2P groups on process termination
Killing the wpa_supplicant process or using TERMINATE ctrl_iface command
resulted in the process existing without cleaning up possibly added
dynamic P2P group interfaces. Clean this up by stopping each P2P group
before stopping eloop.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-09-26 01:38:30 +03:00
Vinay Krishna Eranna
b2b688d18d P2P: Fix crash when failed to create GO interface
wpa_supplicant crashes if driver configuration for AP mode interface
configuration fails after group negotiation. This is because of a
regression from commit 1075b29571 that
ends up freeing the wpa_s instance from within
wpa_supplicant_create_ap() without the caller knowing.

Fix this by using an eloop timeout to free remove the P2P group so that
wpa_supplicant_create_ap() and especially wpa_supplicant_associate()
callers do not need to know about interface getting possibly removed. In
addition, move the P2P specific code into p2p_supplicant.c where it
really belongs. This allows the already existing group formation timeout
to be used by reducing the timeout to zero.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-09-03 12:43:12 +03:00
Jouni Malinen
01a57fe420 P2P: Maintain list of per-client PSKs for persistent groups
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-09-01 21:35:10 +03:00
Jouni Malinen
25a8f9e316 Clear EAPOL supplicant configuration info on current_ssid changes
There were some code paths that allowed obsolete configuration data
pointer to be maintained within EAPOL supplicant in case a network was
removed while not connection to it (i.e., wpa_s->current_ssid not
pointing to the network that was removed). This could result in use of
freed memory, e.g., from eap_sm_notify_ctrl_attached() when a new
control interface connected prior to the EAPOL supplicant configuration
pointer got updated.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-08-25 19:46:57 +03:00
Sean Lin
cbf41ca796 P2P: Do not delay retries on failure during group formation
4-way handshake may fail under extremely noisy environment and if this
happens during P2P group formation, the 10 second extra delay added in
wpas_auth_failed() can result in running over the 15 second timeout.

Avoid this by skipping the delay mechanism in wpas_auth_failed() for the
P2P group formation case. The P2P formation timeout will take care of
stopping the attempts if the failure condition does not get resolved.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-07-31 23:09:34 +03:00
Jouni Malinen
a21816a933 Use wpa_drv_shared_freq() if get_radio_name() is not supported
Some driver interfaces may not support the get_radio_name() design and
get_shared_radio_freqs() needs to be aware of such possibility when
determining shared radio frequencies.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-07-21 20:48:09 +03:00
Ilan Peer
53c5dfc2c4 Change share_vif_oper_freq() to handle multiple freqs
There are devices that can operate several channels concurrently.
Change shared_vif_oper_freq() to get_shared_radio_freqs() that can
return an array of frequencies currently used by all the virtual
interfaces that share the same radio.

In addition, move it to wpa_supplicant.c, so it can be used by other
modules.

Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
2013-07-21 20:03:53 +03:00
Ilan Peer
4752147d88 nl80211: Report the number of concurrent support channels
Previously, drivers only reported if they support multiple concurrent
channels, but did not report the maximum number of supported channels.
Add this reporting to the driver capabilities and add the implementation
to driver_nl80211.

Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
2013-07-21 19:49:47 +03:00
Chengyi Zhao
831770bffe Cancel delayed scheduled scan when wpa_supplicant cleans up
Because a delayed scheduled scan will access the members of struct
wpa_supplicant which is freed and this can result in a crash,
wpa_supplicant needs to cancel delayed scheduled scan during cleanups.

Signed-hostap: Chengyi Zhao <chengyix.zhao@gmail.com>
2013-07-20 17:47:02 +03:00
Jouni Malinen
78f79fe5fc P2P: Do not add ctrl interface for P2P_DEVICE (p2p-dev-*)
Adding a new wpa_supplicant control interface for the dedicated
P2P_DEVICE would be quite confusing for programs that manage P2P
operations. Remove this control interface and require the global control
interface to be used since it will provide consistent interface for both
the new dedicated P2P_DEVICE (non-netdev) and old style P2P management
through a netdev.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-07-01 00:36:33 +03:00
Jouni Malinen
1c42b42f6c P2P: Fix TDLS and l2_packet init without P2P Device interface
Commit c68f6200a7 made these calls
conditional on !p2p_mgmt, but forced p2p_mgmt=1 for cases where the
driver does not use the dedicated P2P Device. Fix this by making the
!p2p_mgmt condition apply only if the driver does indicate use of a
dedicated P2P Device.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-06-30 20:02:25 +03:00
Arend van Spriel
c68f6200a7 P2P: Create P2P Device interface if supported
If the capability flag of the driver indicates a dedicated P2P Device is
supported, a P2P Device interface is created.

Create the P2P Device in main interface creation loop when the added
interface flags support and P2P supplicant is not yet initialized
avoiding recursion of add_interface.

Do not register l2_packet for P2P Device interface (both for EAPOL and
for TDLS).

Signed-hostap: Arend van Spriel <arend@broadcom.com>
2013-06-30 10:50:14 +03:00
Arend van Spriel
72950ed240 P2P: Remove a call to wpas_p2p_deinit_global()
In wpa_supplicant_deinit(), the function wpas_p2p_deinit_global()
was called. Remove it as it will be called from wpas_deinit_iface()
upon removal of the P2P management interface.

Signed-hostap: Arend van Spriel <arend@broadcom.com>
2013-06-25 13:56:28 +03:00
Jouni Malinen
ec7b97ab00 Interworking: Add support for using eap_proxy offload
Fetch IMSI through eap_proxy for Interworking network selection if
needed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-06-19 18:42:17 +03:00
Jouni Malinen
dad153d16b Try to use fast-associate on ENABLE_NETWORK
This makes ENABLE_NETWORK behave similarily to SELECT_NETWORK by
allowing a scan to be skipped if recent scan results are available.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-22 16:10:59 +03:00
Jouni Malinen
2925756575 wpa_supplicant: Add -G argument to specify global ctrl group
The optional -G<group> command line argument can be used to specify the
group that can access the global control interface.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-05-18 11:00:05 +03:00
Vinayak Kamath
e27d20bb68 WNM: Add neighbor report processing for BSS Transition Management
Process the neighbor report received in BSS Management Request frames.

Signed-hostap: Vinayak Kamath <vkamat@codeaurora.org>
2013-05-16 17:48:59 +03:00
Jouni Malinen
e679f140b9 Mark interface disconnected on removal request
This cleans up debug log by not trying to process the disconnection
event as a failure that could result in blacklist addition and auto
connect attempt. These are pointless operations since the interface is
going to removed immediately after this.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-12 19:18:55 +03:00
Jouni Malinen
0cdb93fe9f Do not add BSS to blacklist on local disconnection request
There is no point in marking a BSS temporarily blacklisted based on a
connection failure or disconnection case if that happens as a result of
a local request to disconnect. The blacklist entry could result on
unexpected BSS getting selected on the next connection attempt. In
addition, the code to try to find another BSS within the ESS could
result in scanning a single channel on the next attempt. Fix these
issues by handling the connection failure events only if we are not in
disconnected state (i.e., would try to reconnect after this
automatically).

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-12 19:18:55 +03:00
Deepthi Gowri
36b9883d84 Defer scan if connection is in progress on any of the shared interfaces
Scanning can delay concurrent operations considerably, so it is better
to avoid that while trying to connect on any of the virtual interfaces
that share the same radio.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-10 16:10:50 +03:00
Jouni Malinen
6ea1f4135b Try to set WPA-None key after IBSS-joined event
cfg80211 rejects the set_key operations before the IBSS network has been
fully formed, so add one more attempt to set the key for WPA-None at
IBSS joined driver event.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-07 18:14:56 +03:00
Jouni Malinen
66562e9c75 Use cached driver capabilities instead of new fetch for each operation
There is no need to repeat the driver capability fetch for each
operation since we already cache driver flags in wpa_s->drv_flags.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-07 17:36:40 +03:00
Jouni Malinen
55a2df4389 HS 2.0: Include HS 2.0 Indication element only for HS 2.0 association
The Hotspot 2.0 specification seems to mandate this element to be
included in all (Re)Association Request frames if the station is Hotspot
2.0 capable. However, that results in conflicts with other requirements
like no TKIP use when this element is present. The design is really
supposed to include the indication element only for Hotspot 2.0
associations regardless of what the current specification implies.
Remove the HS 2.0 Indication element from (Re)Association Request frame
whenever the connection is not for Hotspot 2.0 purposes.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-05-05 16:29:21 +03:00
Jouni Malinen
dd57970477 Disable network temporarily on repeated connection failures
Previously, only explicit indications of authentication failures were
used to disable a network block temporarily. Extend this to use multiple
failed connection attempts as a sign of a possible authentication or
authorization failure to reduce the frequency of connection attempts
with a network that does not seem to allow connection.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-04-25 17:28:50 +03:00
Jouni Malinen
18e00b5e4d Move wpa_s freeing into wpa_supplicant_deinit_iface()
All wpa_supplicant_deinit_iface() callers ended up freeing wpa_s
immediately after this call. Move os_free(wpa_s) into the deinit
function to share the same call and make the deinit sequence clearer.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-04-23 18:07:41 +03:00
Dmitry Shmidt
e6304cad47 wpa_supplicant: Add option -I for additional config file
This option can be used only for global parameters that are not going
to be changed from settings.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Iliyan Malchev <malchev@google.com>
2013-04-23 17:38:57 +03:00
Jouni Malinen
3db5439a5f Optimize Extended Capabilities element to be of minimal length
Leave out zero octets from the end of the element.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-03-31 21:58:17 +03:00
Johannes Berg
8cd6b7bce8 hostapd/wpa_s: Use driver's extended capabilities
Some extended capabilities (I'm currently interested in "Operating Mode
Notification" for VHT) are implemented by the kernel driver and exported
in nl80211. Use these in hostapd/wpa_supplicant.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-03-31 21:51:44 +03:00
Jouni Malinen
f85f545e71 P2P: Use common function for re-starting P2P scan after station scan
Make the implementation more consistent and cleaner by using a single
function for addressing all the cases where completion of a station mode
scan operation allows a P2P operation (search) to be re-started.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-18 17:32:31 +02:00
Partha Narasimhan
b2a12c4f93 wpa_supplicant: Fix lookup of cached PMKSA
This fixes the lookup of a usable PMKSA entry in the cache. Using
wpa_s->current_ssid often returns nothing when a usable PMKSA exists in
the cache since wpa_s->current_ssid does not necessarily point to the
correct network entry at this point in time (prior to association).

Signed-hostap: Partha Narasimhan <parthan@gmail.com>
2013-03-16 12:45:31 +02:00
Solomon Peachy
7d37a357fa Fix build without CONFIG_CTRL_IFACE or CONFIG_NO_STDOUT_DEBUG
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
2013-03-16 12:07:18 +02:00
Jouni Malinen
dbca75f82a P2P: Remove persistent group peer if it rejects invitation
If a peer replies to persistent group invitation with status code 8
(unknown group), remove the peer from the p2p_client_list if we are the
GO or remove the persistent group if we are the P2P client since it
looks like that the peer has dropped persistent group credentials and
the provisioning step needs to be executed again.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-15 16:43:06 +02:00
Johannes Berg
e9ee8dc394 wpa_supplicant: Support VHT capability overrides
Add support for VHT capability overrides to allow testing connections
with a subset of the VHT capabilities that are actually supported by
the device. The only thing that isn't currently supported (by mac80211
and this code) is the RX/TX highest rate field.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-03-10 18:04:39 +02:00
David Spinadel
725fc39e07 wpa_supplicant: Reschedule sched scan after network change
Stop sched scan, if running, after any disabling or removing of
a network, and request a new scan if needed.

Signed-hostap: David Spinadel <david.spinadel@intel.com>
2013-03-10 17:51:13 +02:00
Jouni Malinen
14f7907890 Remove unnecessary local variable
The ssid parameter (if NULL) can be used for the loop, too, to make the
code look a bit prettier.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-03-10 17:45:15 +02:00
David Spinadel
dca1a51149 wpa_supplicant: Handle enabling of one or all networks equally
Move enabling a network to a separate function. Try to reconnect if not
associated to an AP. Abort scheduled scan in any case of a new scan.

Signed-hostap: David Spinadel <david.spinadel@intel.com>
2013-03-10 17:43:00 +02:00
Masashi Honma
5e24beae02 Use scan results for reconnection
This patch uses existing scan results for fast connection on REASSOCIATE
and RECONNECT commands.

Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
2013-02-28 16:34:08 +02:00
Sunil Dutt
7b44ff2c21 TDLS: Tear down peers when disconnecting from the AP
A TDLS Teardown frame with Reason Code 3 (Deauthenticated because
sending STA is leaving (or has left) IBSS or ESS) shall be transmitted
to all TDLS peer STAs (via the AP or via the direct path) prior to
transmitting a Disassociation frame or a Deauthentication frame to the
AP.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-02-13 01:19:44 +02:00
Paul Stewart
cecdddc184 wpa_supplicant: Implement fast-associate on SelectNetwork
If scan results are available when we perform a SelectNetwork, use
them to make an associate decision.  This can save an entire scan
interval-worth of time in situations where something external to
wpa_supplicant (like a connection manager) has just previously
requested a scan before calling SelectNetwork.

Signed-hostap: Paul Stewart <pstew@chromium.org>
2013-02-03 21:08:31 +02:00
Pontus Fuchs
9e737f08d4 Update scan interval gracefully
When the scan interval is changed the new interval is effective
after the old interval timer fires off one last time. This can cause
an unacceptable long delay when updating the interval.

Change this behaviour to use MIN(left of old interval, new interval)
for the scan interval following the interval change.

Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
2013-02-03 18:14:05 +02:00
Jouni Malinen
62769a88db Move cipher to enum wpa_cipher conversion into wpa_common.c
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-13 18:02:20 +02:00
Jouni Malinen
edbd2a191e Move cipher suite selection into common helper functions
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-13 16:58:54 +02:00
Jouni Malinen
e056f93e60 Update copyright notices to include year 2013
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:53 +02:00
Jouni Malinen
1cfc678723 Remove reassociated_connection variable
This was used to select between "(auth)" and "(reauth)" in
CTRL-EVENT-CONNECTED events. However, the variable was not cleared
anywhere else apart from the AP deinit case. As such, it did not really
provide correct information and is not really of much use even with
proper clearing added. As such, it is cleaner to just get rid of this
altogether.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-25 19:51:04 +02:00
Jouni Malinen
2049a875bc WNM: Additional BSS Transition Management capability
Add some more functionality for BSS Transition Management:
- advertise support for BSS Transition Management in extended
  capabilities element
- add hostapd.conf parameter bss_transition=1 for enabling support
  for BSS Transition Management
- add "hostapd_cli disassoc_imminent <STA> <num TBTTs>" for sending
  disassociation imminent notifications for testing purposes
- wpa_supplicant: trigger a new scan to find another BSS if the
  current AP indicates disassociation imminent (TODO: the old AP needs
  to be marked to use lower priority to avoid re-selecting it)

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-22 20:27:30 +02:00
Jouni Malinen
03e47c9c3a Share a single function for building extended capabilities element
This makes it easier to update extended capabilities for all uses
within wpa_supplicant.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-22 19:17:15 +02:00
Jouni Malinen
3ab35a6603 Extend EAPOL frames processing workaround for roaming cases
Commit 1ff733383f added a mechanism to
work around issues due to association events and EAPOL RX events being
getting reordered. However, this applied only for the case where
wpa_supplicant is not in associated state. The same issue can happen in
roaming case with drivers that perform BSS selection internally (or in
firmware). Handle that case similarly by delaying received EAPOL frame
processing if the source address of the EAPOL frame does not match the
current BSSID.

Since wired IEEE 802.1X do not have BSSID, make this additional
workaround conditional on BSSID match having been observed during the
previous association.

This fixes issues where the initial EAPOL frame after reassociation was
either dropped (e.g., due to replay counter not increasing) or replied
to with incorrect destination address (the BSSID of the old AP). This
can result in significantly more robust roaming behavior with drivers
that do not use wpa_supplicant for BSS selection.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-21 21:35:35 +02:00
Ben Greear
a90497f85f wpa_supplicant: Allow user to disable short guard interval (SGI)
Requires Linux kernel patch to make the SGI-20 properly disabled. SGI-40
will already work since Linux 3.4 or so.

Signed-hostap: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
2012-12-18 14:45:09 +02:00
Jouni Malinen
e6955ba9f9 WNM: Add WNM-Sleep Mode into Extended Capabilities element
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:45:59 +02:00
Jouni Malinen
9796a86c23 Use a shared function for requesting a new connection
Both the ctrl_iface and D-Bus interface use similar functionality to
request a new connection. Combine these to a single function to avoid
need to maintain duplicated implementation.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-25 16:30:30 +02:00
Jouni Malinen
f1a5263389 Maintain maximum blacklist count over list clear operations
wpas_connection_failed() uses the blacklist count to figure out a
suitable time to wait for the next scan. This mechanism did not work
properly in cases where the temporary blacklist gets cleared due to no
other BSSes being available. Address this by maintaining an additional
count of blacklisting values over wpa_blacklist_clear() calls. In
addition, add one more step in the count to timeout mapping to go to 10
second interval if more than four failures are seen.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-25 16:20:44 +02:00
Jouni Malinen
4115303bbe Document wpa_s->scan_req
Use an enum with documented values to make it easier to understand how
wpa_s->scan_req is used.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-25 15:55:32 +02:00
Jouni Malinen
62d4980331 Allow PMF to be enabled by default
Previously, PMF (protected management frames, IEEE 802.11w) could be
enabled only with a per-network parameter (ieee80211w). The new global
parameter (pmf) can now be used to change the default behavior to be PMF
enabled (pmf=1) or required (pmf=2) for network blocks that do not
override this with the ieee80211w parameter.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-24 22:21:29 +02:00
Jouni Malinen
6e2020210a Allow OKC to be enabled by default
Previously, OKC (opportunistic key caching, a.k.a. proactive key
caching) could be enabled only with a per-network parameter
(proactive_key_caching). The new global parameter (okc) can now be used
to change the default behavior to be OKC enabled (okc=1) for network
blocks that do not override this with the proactive_key_caching
parameter.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-11-12 20:07:53 +02:00
Jouni Malinen
1e8a6e7553 Remove unused wpa_supplicant_disassociate()
This function is now unused after the last couple of commits that
removed the last uses, so remove this to keep code simpler since all
places that disassociate, can use deauthentication instead.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-11-05 17:05:37 +02:00
Jouni Malinen
07783eaaa0 Use deauthentication instead of disassociation if not associated
cfg80211/mac80211 may reject disassociation command if association has
not yet been formed. Use deauthentication in cases where it is possible
that we are associating at the moment the command is issued.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-11-05 16:58:00 +02:00
Jouni Malinen
42d235477f Use wpa_drv_{disassociate,deauthenticate} while waiting for connection
wpa_supplicant_{disassociate,deauthenticate}() need to inform the driver
about decision to disconnect even if this happens during the time when
the driver is still trying to complete association. During that time,
wpa_s->bssid is not set, so the code in these functions needs to figure
out the correct BSSID based on that field or wpa_s->pending_bssid. In
addition, it is possible that the BSSID is not even known at
wpa_supplicant at this point in time when using drivers that perform BSS
selection internally. In those cases, the disconnect command needs to be
sent to the driver without the BSSID.

This fixes issues where the driver (or cfg80211 in particular) may be
left in mismatching state with wpa_supplicant when disconnection (e.g.,
due to a ctrl_iface command) happens between connection request and
association event.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-11-05 16:57:57 +02:00
Jouni Malinen
c10347f246 Add initial parts for SAE
This introduces new AKM for SAE and FT-SAE and adds the initial parts
for going through the SAE Authentication frame exchange. The actual SAE
algorithm and new fields in Authentication frames are not yet included
in this commit and will be added separately. This version is able to
complete a dummy authentication with the correct authentication
algorithm and transaction values to allow cfg80211/mac80211 drivers to
be tested (all the missing parts can be handled with
hostapd/wpa_supplicant changes).

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-30 19:51:07 +03:00
Jouni Malinen
6407f4132f Add disallow_aps parameter to disallow BSSIDs/SSIDs
External programs can use this new parameter to prevent wpa_supplicant
from connecting to a list of BSSIDs and/or SSIDs. The disallowed BSSes
will still be visible in scan results and it is possible to run ANQP
operations with them, but BSS selection for connection will skip any
BSS that matches an entry in the disallowed list.

The new parameter can be set with the control interface SET command
using following syntax:

SET disallow_aps <disallow_list>
disallow_list ::= <ssid_spec> | <bssid_spec> | <disallow_list> | “”
SSID_SPEC ::= ssid <SSID_HEX>
BSSID_SPEC ::= bssid <BSSID_HEX>

For example:
wpa_cli set disallow_list "ssid 74657374 bssid 001122334455 ssid 68656c6c6f"
wpa_cli set disallow_list
(the empty value removes all entries)

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-09-27 17:36:59 +03:00
Dan Williams
8c981d179b wpa_supplicant: Set state to DISCONNECTED on AP creation errors
If the AP creation failed (missing freq= or driver error) the supplicant
would previously stay in SCANNING state forever. Instead, it should
handle the error a bit better and drop back to DISCONNECTED so clients
know something went wrong.

Signed-hostap: Dan Williams <dcbw@redhat.com>
intended-for: hostap-1
2012-09-23 13:55:58 +03:00
Jouni Malinen
e665ca9a8d P2P: Move p2p_cb_on_scan_complete to global context
Since we have a global P2P module, the flag to trigger scan completion
events to it needs to be in similar context. The previous design
maintained this separately for each virtual interface and if P2P module
did not run its scan operation on the virtual interface that completed
the scan, P2P module would not be allowed to restart operations
properly.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-13 17:58:22 -07:00
Jouni Malinen
a297201df1 Maintain list of BSS entries in last scan result order
This allows last results to be used even after they have been freed
since the information is copied to the BSS entries anyway and this new
array provides the order in which scan results were processed.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-02 19:53:15 +03:00
Jouni Malinen
9675ce354a WFD: Add Wi-Fi Display support
This commit adds control interface commands and internal storage of
Wi-Fi Display related configuration. In addition, WFD IE is now added
to various P2P frames, Probe Request/Response, and (Re)Association
Request/Response frames. WFD subelements from peers are stored in the
P2P peer table.

Following control interface commands are now available:
SET wifi_display <0/1>
GET wifi_display
WFD_SUBELEM_SET <subelem> [hexdump of length+body]
WFD_SUBELEM_GET <subelem>

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-29 19:51:29 +03:00
Jouni Malinen
eb7719ff22 Add support for using GCMP cipher from IEEE 802.11ad
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.

This commit does not included changes to WPS or P2P to allow GCMP to be
used.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-29 11:52:15 +03:00
Jouni Malinen
b1f122964e Add generic GAS request mechanism
The new gas_request and gas_response_get commands can be used to request
arbitary GAS queries to be performed. These can be used with ANQP or
with other (including vendor specific) advertisement protocols.

gas_request <BSSID> <AdvProtoID> [Query]
gas_response_get <addr> <dialog token> [offset,length]

For example, ANQP query for Capability list in interactive wpa_cli
session:

> gas_request 02:00:00:00:01:00 00 000102000101
<3>GAS-RESPONSE-INFO addr=02:00:00:00:01:00 dialog_token=0
status_code=0 resp_len=32
> gas_response_get 02:00:00:00:01:00 00
01011c00010102010501070108010c01dddd0c00506f9a110200020304050607
> gas_response_get 02:00:00:00:01:00 00 0,10
01011c00010102010501
> gas_response_get 02:00:00:00:01:00 00 10,10
070108010c01dddd0c00
> gas_response_get 02:00:00:00:01:00 00 20,10
506f9a11020002030405
> gas_response_get 02:00:00:00:01:00 00 30,2
0607

It should be noted that the maximum length of the response buffer is
currently 4096 bytes which allows about 2000 bytes of the response data
to be fetched with a single gas_response_get command. If the response is
longer, it can be fetched in pieces as shown in the example above.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-27 18:13:10 +03:00
Jouni Malinen
0d30cc240f Clear current_ssid and key_mgmt when disconnected
This makes wpa_supplicant state somewhat cleaner since the information
from previously used connection is not maintained after getting
disconnected.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-26 23:35:08 +03:00
Jouni Malinen
00e5e3d509 Disable network block temporarily on authentication failures
If 4-way handshake fails due to likely PSK failure or if EAP
authentication fails, disable the network block temporarily. Use longer
duration if multiple consecutive failures are seen.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-26 23:35:07 +03:00
Jouni Malinen
cc8c7b8840 P2P: Remove unnecessary call in resuming p2p_find
Commit 99fcd40409 added a call to update
search delay after failed authentication attempt. This change was
supposed to be only in p2p_supplicant.c for the successful case. The
extra call does not really do anything, but it's good to remove it to
avoid any confusion in the future.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-23 20:28:04 +03:00
Jouni Malinen
99fcd40409 P2P: Allow scan operations during p2p_find
Previously, all station mode scan operations were either skipped or
delayed while any P2P operation was in progress. To make concurrent
operations easier to use, reduce this limitation by allowing a scan
operation to be completed in the middle of a p2p_find. In addition,
allow station mode association to be completed. When the station mode
operation is run to its completion (scan results not acted on,
connection to an AP completed, connection failed), resume the p2p_find
operation.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-23 19:42:53 +03:00
Yoni Divinsky
6409b7a715 Supply the connection scan results to bgscan after init
If bgscan is enabled, then bgscan is initiated after the connection,
with no bss scan result information. Since a scan was performed prior to
the connection, the information exists and can be used to initialize the
bgscan's cache.

Signed-hostap: Yoni Divinsky <yoni.divinsky@ti.com>
2012-08-17 20:53:44 +03:00
Jouni Malinen
a3f7e5186b Allow non-WPA IEEE 802.1X to be select even if WPA is also enabled
If key_mgmt was set to allow both WPA and non-WPA IEEE 802.1X (i.e., to
IEEE8021X WPA-EAP), non-WPA IEEE 802.1X was rejected while preparing
association parameters. Allow this special case to be handled by
selecting non-WPA case if the scan results for the AP do not include
either WPA or RSN elements.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-15 19:34:04 +03:00
Jouni Malinen
986de33d5c Convert remaining SSID routines from char* to u8*
This makes it more explicit that the SSID is not a null terminated
C string.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-07 16:07:25 +03:00
Jouni Malinen
9173b16fd1 EXT PW: Add support for psk parameter from external storage
This allows wpa_supplicant configuration file to be created without
the PSK/passphrase value included in the file when a backend for
external password storage is available.

Following example can be used for developer testing:

ext_password_backend=test:psk1=12345678
network={
    ssid="test-psk"
    key_mgmt=WPA-PSK
    psk=ext:psk1
}

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-03 22:15:42 +03:00
Jouni Malinen
306ae22556 EXT PW: Add framework for supporting external password storage
This new mechanism can be used to make wpa_supplicant using external
storage (e.g., key store in the operating system) for passwords,
passphrases, and PSKs. This commit is only adding the framework part
needed to support this, i.e., no actual configuration parameter can
yet use this new mechanism. In addition, only a simple test backend
is added to allow developer testing of the functionality.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-03 22:15:42 +03:00
Jouni Malinen
2518aad3e8 Move PSK/passphrase configuration check into use time from parsing
Instead of rejecting network blocks without PSK/passphrase at the time
the configuration file is read, allow such configuration to be loaded
and only behave as if the network block with missing PSK/passphrase is
disabled.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-03 22:15:42 +03:00
Jouni Malinen
c3d1223848 Reinitialize autoscan on explicit reassocciate/reconnect command
This clears the exponential scan interval back to the base value
when a reconnection is requested explicitly.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-06-26 20:05:51 +03:00
Jouni Malinen
992189991c Start autoscan for first connection attempt
Use wpa_supplicant_set_state() to initialize state to DISCONNECT so that
autoscan gets initialized properly. This needs a change in
autoscan_init() to avoid extra scan request that would postpone the
first scan request when an interface is added.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-06-26 19:52:46 +03:00
Tomasz Bursztyka
7c865c6853 Add automatic scanning support
Like bgscan, autoscan is an optional module based feature to automate
scanning but while disconnected or inactive.

Instead of requesting directly a scan, it only sets the scan_interval
and the sched_scan_interval. So, if the driver supports sched_scan,
autoscan will be able to tweak its interval. Otherwise, the tweaked
scan_interval will be used. If scan parameters needs to be tweaked, an
autoscan_params pointer in wpa_s will provide those. So req_scan /
req_sched_scan will not set the scan parameters as they usually do, but
instead will use this pointer.

Modules will not have to request a scan directly, like bgscan does.
Instead, it will need to return the interval it wants after each
notification.

Signed-hostap: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2012-06-26 18:55:41 +03:00
Jouni Malinen
c1c023429b Set state to DISCONNECTED on auth/assoc failures
Some of the authentication/association failure paths left wpa_state to
its previous value. This can result in unexpected behavior when
wpa_supplicant tries to find an AP to connect to since the uncleared
state can result the in the selected BSS being ignored if it is same as
the previously used BSS. This could happen, e.g., when wpa_supplicant
SME was used and the AP rejected authentication. Fix this by explicitly
setting state to DISCONNECTED on auth/assoc failures that did not yet do
this.

Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
2012-06-25 14:23:25 +03:00
Jithu Jance
b9cfc09a81 P2P: Add preference setting for concurrent use cases
Add an additional parameter to prioritize either sta or p2p connection
to resolve conflicts arising during single channel concurrency.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2012-06-10 20:53:09 +03:00
Jouni Malinen
b6668734ab WNM: Add advertisement of BSS max idle period
If WNM is enabled for the build (CONFIG_WNM=y), add BSS max idle period
information to the (Re)Association Response frame from the AP and parse
this information on the station. For SME-in-wpa_supplicant case, add a
timer to handle periodic transmission of the keep-alive frame. The
actual request for the driver to transmit a frame is not yet
implemented.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-05-27 17:35:00 -07:00
Jouni Malinen
f15854d1e1 Fix BSSID enforcement with driver-based BSS selection
Previously, wpa_supplicant did not specify BSSID to any connection
request if the driver indicated that it will take care of BSS selection.
This is fine for most use cases, but can result to issues if the network
block has an explicit bssid parameter to select which BSS is to be used.
Fix this by setting BSSID and channel when the network block includes the
bssid parameter even if the driver indicates support for BSS selection.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-05-11 15:27:46 +03:00
Jouni Malinen
349493bd0c Validate WEP key lengths based on driver capabilities
The nl80211 driver interface does not allow 128-bit WEP to be used
without a vendor specific cipher suite and no such suite is defined for
this purpose. Do not accept WEP key length 16 for nl80211 driver
interface forn ow. wext-interface can still try to use these for
backwards compatibility.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-10 14:34:46 +03:00
Jouni Malinen
ab28911dbf P2P: Deinitialize global P2P context on P2P mgmt interface removal
The P2P implementation assumes that the first wpa_s interface instance
is used to manage P2P operations and the P2P module maintains a pointer
to this interface in msg_ctx. This can result in issues (e.g., use of
freed memory) when the management interface is removed. Fix this by
deinitializing global P2P data if the interface that created it is
removed. This will disable P2P until the next interface is added.

Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
2012-05-10 10:49:22 +03:00
Jouni Malinen
cb4183249f HS 2.0: Add HS 2.0 Indication element into (Re)Association Request
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-08 23:30:04 +03:00
Jouni Malinen
fea7c3a055 Ignore network blocks that have invalid WEP key length
Do not try to associate with a network that has an invalid or incomplete
configuration because the association or at least data connection would
fail anyway. This commits adds a common function for checking whether a
network block is disabled to make it easier to check network blocks
without having to reject them during configuration file parsing (which
would prevent wpa_supplicant from starting). The only additional check
added in this commit is to verify the WEP key length. Similar checks for
other parameters can be added in future commits.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-07 13:39:33 +03:00
Rajkumar Manoharan
c3701c66a5 Add handling of OBSS scan requests and 20/40 BSS coex reports
Add support for HT STA to report 40 MHz intolerance to the associated AP.
A HT station generates a report (20/40 BSS coexistence) of channel list
if it finds a non-HT capable AP or a HT AP which prohibits 40 MHz
transmission (i.e., 40 MHz intolerant bit is set in HT capabilities IE)
from the scan results.

Parse the OBSS scan parameter from Beacon or Probe Response frames and
schedule periodic scan to generate 20/40 coexistence channel report if
requested to do so. This patch decodes Scan Interval alone from the OBSS
Scan Parameters element and triggers scan on timeout.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-03 15:55:38 +03:00
Jouni Malinen
d211881474 Fix D-Bus build without ctrl_iface
Commit 7de5688d68 started using
wpa_supplicant_ctrl_iface_ctrl_rsp_handle() from the D-Bus code, but
left this function in ctrl_iface.c that is included conditionally. Fix
this by moving the common function into wpa_supplicant.c so that it can
be included for builds that include only either ctrl_iface or D-Bus.

Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
2012-04-27 21:21:31 +03:00
Mukesh Agrawal
c6e86b63d2 Create DBus getter/setter for ScanInterval
Enable control of wpa_s->scan_interval via D-Bus. This parameter
controls the delay between successive scans for a suitable AP.

Also, update dbus.doxygen with ScanInterval, and some other
parameters that were undocumented.

Signed-hostap: Mukesh Agrawal <quiche@chromium.org>
2012-04-01 18:05:22 +03:00
Johannes Berg
4f68895e92 debug: Add option to log to Linux tracing
Add the option (-T) to wpa_supplicant to log all debug messages into the
kernel tracing, allowing to aggregate kernel debugging with
wpa_supplicant debugging and recording all with trace-cmd.

Since tracing has relatively low overhead and can be filtered
afterwards, record all messages regardless of log level. However, it
will honor the -K option and not record key material by default.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2012-03-31 13:55:33 +03:00
Bala Shanmugam
1f6c0ab872 Allow background scan period to be configured
A network block specific background scan period can now be configured
for drivers that implement internal background scan mechanism for
roaming and BSS selection.

Signed-hostap: Bala Shanmugam <bkamatch@qca.qualcomm.com>
2012-03-30 15:20:35 +03:00