Reduce testing dependency on the unsuitable groups so that a test case
against a production build would not fail the test case unnecessarily.
This is in preparation of making production builds
(CONFIG_TESTING_OPTIONS not defined) of wpa_supplicant hostapd disable
all DH groups that have been indicated as being unsuitable.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Accept a smaller number of token responses in second round to avoid
failing this test case as frequently.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Configure the sae_groups parameter for hostapd explicitly in preparation
for the default value change in the implementation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is easier to understand the hostapd debug log here if each step is
noted there before starting the wpa_supplicant operation. In addition,
it looks safer to process all pending event messages between each step
to avoid running out of any buffer limits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This does not really work with mac80211_hwsim due to missing offload
support, but at least some minimal extra code coverage can be achieved.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Beacon more frequently since Probe Request frames are practically ignored
in this test setup (ext_mgmt_frame_handled=1 on hostapd side) and
wpa_supplicant scans may end up getting ignored if no new results are
available due to the missing Probe Response frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
After successfully passing the 525 tests on a remote setup mark the
tests as remote compatible.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (4) converts the cases that call hostapd.add_ap() from a
helper function that got apdev[i] as an argument.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (1) converts the cases where apdev[#]['ifname'] was used as
the argument to hostapd.add_ap().
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The decrypted copy of a GTK from EAPOL-Key is cleared from memory only
after having sent out CTRL-EVENT-CONNECTED. As such, there was a race
condition on the test case reading the wpa_supplicant process memory
after the connection. This was unlikely to occur due to the one second
sleep, but even with that, it would be at least theorically possible to
hit this race under heavy load (e.g., when using large number of VMs to
run parallel testing). Avoid this by running a PING command to make sure
wpa_supplicant has returned to eloop before reading the process memory.
This should make it less likely to report false positives on GTK being
found in memory.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like it is possible for the GTK to be found from memory every
now and then. This makes these test cases fail. Write the memory
addresses in which the GTK was found to the log to make it somewhat
easier to try to figure out where the key can be left in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like NID_X9_62_prime192v1 is not available, so allow that group
to fail without failing the full sae_groups test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This changes the sae_groups test case design to try with every group and
skip triggering test failure for the heavier ones that are likely to
fail in some VM setups under load. This provides more testing coverage
by not limiting the test based on lowest common setup.
Signed-off-by: Jouni Malinen <j@w1.fi>
