This allows DH key generation to be shared for other purposes than just
the case of OOB Device Password building. In addition, force the DH
public key buffer to be full 192 octets with zero padding to avoid
issues with the buffer being used in messages sent to a peer device.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new Device Password ID 7 is used to indicate that NFC connection
handover is used with DH public key hash from both devices being
exchanged over the NFC connection handover messages. This allows an
abbreviated M1-M2 handshake to be used since Device Password does not
need to be used when DH is authenticated with the out-of-band
information (validation of the public key against the hash).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When both the Registrar and Enrollee public key hashes are delivered
out-of-band (in NFC connection handover), use abbreviated WPS handshake
(skip M3-M8).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the SSID of the WPS AP is known, it should be possible to limit AP
selection based on this when searching for an active WPS AP. This commit
adds a mechanism to specify SSID for this type of uses.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the Enrollee can now get the public key hash from the Registrar,
there is need to validate this during the WPS protocol run.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of terminating the WPS protocol immediately, go through an M2D
exchange to notify Enrollee of the public key hash mismatch.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This old Version attribute is not really needed anymore for these use
cases with the assumption that there are no existing WPS+NFC
deployments. It was removed from the WSC specification, so make the
implementation match that change.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Provide local GO channel to the P2P module so that it can be used in
messages that indicate the current operating channel.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This functionality is needed for other messages, too, so split the group
info building code into a separate helper function.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a QCA vendor specific nl80211 event to allow the driver to
indicate a list of frequency ranges that should be avoided due to
interference or possible known co-existance constraints. Such
frequencies are marked as not allowed for P2P use to force groups to be
formed on different channels.
If a P2P GO is operating on a channel that the driver recommended not to
use, a notification about this is sent on the control interface and
upper layer code may decide to tear down the group and optionally
restart it on another channel. As a TODO item, this could also be changed
to use CSA to avoid removing the group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This file is used as a registry of identifier assignments from the
Qualcomm Atheros OUI 00:13:74 for purposes other than MAC address
assignment. One of the first uses will be for nl80211 vendor
commands/events which is reason for the preparation change in
driver_nl80211.c
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the global ctrl_iface can be used with IFNAME= prefix to send
commands to be processed by per-interface code, it should have the same
(well, close to same since the prefix takes some space) limits on
command length as the per-interface ctrl_iface. Increase the buffer from
256 to 4096 to achieve this.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When GAS is used with PMF negotiated, Protected Dual of Public Action
frames are expected to be used instead of Public Action frames, i.e.,
the GAS/ANQP frames are expected to be encrypted. Conver Public Action
GAS queries to use Dual of Public Action frame if PMF has been
negotiated with the AP to which the frame is being sent.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When GAS is used with PMF negotiated, Protected Dual of Public Action
frames are expected to be used instead of Public Action frames, i.e.,
the GAS/ANQP frames are expected to be encrypted. Add support for this
different category of Action frames being used for GAS. The payload
after the Category field is identical, so the only change is in using
the Category field based on what was received in the request frames. For
backwards compatibility, do not enforce protected dual to be used on the
AP side, i.e., follow what the station does.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Due to misplaced parenthesis, unprotected not-Robust Action frames
(e.g., Public Action frames) were dropped in handle_assoc() when such
frames were received during an association that had negotiated use of
PMF. This is not correct since only unprotected Robust Action frames
were supposed to be handled in this way.
This would have broken any Public Action frame use during PMF
association, but such frames were not really supposed to be used
currently (ANQP as the only possible use case should really use
protected dual option in such case).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it more convenient for test scripts to change parameters for
a specific test case without having to separately clear them between
each test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When start PNO request comes from control interface, wpa_supplicant
should wait until ongoing sched_scan (triggered by wpa_supplicant)
gets cancelled. Issuing cancel sched_scan and start PNO scan
one after another from pno_start() would lead wpa_supplicant to clear
wps->sched_scanning flag while getting sched_scan stopped event
from driver for cancel sched_scan request. In fact, PNO scan will
be in progress in driver and wpa_s->sched_scanning will not be set
in such cases.
In addition to this change, RSSI threshold limit is passed as part of
start sched_scan request. This was previously set only in pno_start(),
but the same parameter should be available for generic sched_scan calls
as well and this can now be reached through the new PNO start sequence.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Fix sizeof in a validity comparison of nl80211_vendor_cmd_info size. The
incorrect version happened to work on 64-bit builds due the structure
being eight octets, but this was incorrect and would not used with
32-bit builds.
Signed-hostap: Max Stepanov <Max.Stepanov@intel.com>
While iterating over the stations hostapd_ctrl_iface_sta_mib()
might be called with sta == NULL. Fix this.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Verify wpa_s->radio pointer before accessing it. If interface addition
fails, this could get called before wpa_s->radio has been set.
The segmentation fault details:
Program received signal SIGSEGV, Segmentation fault.
0x00000000004b9591 in wpas_ctrl_radio_work_flush (wpa_s=0x77fff0) at ctrl_iface.c:5754
5754 dl_list_for_each_safe(work, tmp, &wpa_s->radio->work,
Call stack:
0 wpas_ctrl_radio_work_flush (wpa_s=0x77fff0) at ctrl_iface.c:5754
1 wpa_supplicant_deinit_iface (wpa_s=0x77fff0, notify=0, terminate=0) at wpa_supplicant.c:3619
2 wpa_supplicant_add_iface (global=0x75db10, iface=0x7fffffffe270) at wpa_supplicant.c:3691
3 wpas_p2p_add_p2pdev_interface (wpa_s=0x75dd20) at p2p_supplicant.c:3700
4 main (argc=<optimized out>, argv=<optimized out>) at main.c:317
Function:
5750 void wpas_ctrl_radio_work_flush(struct wpa_supplicant *wpa_s)
5751 {
5752 struct wpa_radio_work *work, *tmp;
5753
5754 dl_list_for_each_safe(work, tmp, &wpa_s->radio->work,
5755 struct wpa_radio_work, list) {
5756 struct wpa_external_work *ework;
5757
5758 if (os_strncmp(work->type, "ext:", 4) != 0)
Root cause:
(gdb) p wpa_s->radio
$1 = (struct wpa_radio *) 0x0
Signed-hostap: Max Stepanov <Max.Stepanov@intel.com>
The new default value (from 300 to 60 seconds) makes the internal P2P
peer list somewhat faster to react to peers becoming unreachable while
still maintaining entries for some time to avoid them disappearing
during user interaction (e.g., selecting a peer for a connection or
entering a PIN).
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Scan request failures are observed in wpa_supplicant debug log when
Android framework starts PNO scan in driver via ctrl interface command
'set pno 1' and wpa_supplicant also tries to issue a scan request after
PNO has started in the driver.
Some drivers may reject a normal scan request when PNO is already in
progress. wpa_supplicant should consider PNO status before issuing start
scan request to the driver. Otherwise, wpa_supplicant will get failures
from driver for the scan request and it will end up rescheduling scan
request in periodic interval and get a start scan request failure for
each attempt.
In order to avoid unnecessary scan attempt when PNO scan is already
running, PNO status is checked before issuing scan request to driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A P2P Device while in the Listen state waiting to respond for the
obtained group negotiation request shall give a fair chance for other
concurrent sessions to use the shared radio by inducing an idle time
between the successive listen states. However, if there are no
concurrent operations, this idle time can be reduced.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that PD Request followed by GO Negotiation Request is enough to
learn the Listen frequency of the peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, GO Negotiation Request frame was used to update a peer entry
if only a Probe Request from that peer had been received. However, it
would be possible, even if unlikely, for a peer to be discovered based
on receiving Provision Discovery Request frame from it and no Probe
Request frame. In such a case, the Listen frequency of the peer would
not be known and group formation could not be (re-)initialized with that
peer. Fix this by allowing the GO Negotiation Request frame to update
peer entry if the current peer entry does not include Listen or
Operating frequency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
To test the code under the influence of time jumps, add the option
(--timewarp) to the VM tests to reset the clock all the time, which
makes the wall clock time jump speed up 20x, causing gettimeofday()
to be unreliable for timeout calculations.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
It should be noted that these commands are not exclusively used for P2P
or in the global context, so use of these commands through the global
control interface for operations that are specific to a single interface
have undefined behavior and that behavior may change in the future. As
such, these are recommend only for operations that are in the global
context (e.g., for P2P management).
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Use P2P GO's operating channel information, if known, to do a single
channel scan during the join operation.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
This adds one more case of active P2P peer detection so that
p2p_expire_peers() cannot hit a case where a GO Negotiation peer would
be removed.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
This patch resets the static interface_count to zero in case of
wpa_supplicant_driver_init() call for wpa_s which is in
INTERFACE_DISABLED state. This interface_count is used for the delay of
the scan which is now minimal for dynamically added interfaces. This may
collide with a scan for another interface, but the same is true for any
chosen delay in this scenario. Also the state change to DISCONNECTED is
moved to wpa_supplicant_driver_init() so it will move from
INTERFACE_DISABLED to INACTIVE when there are no enabled networks.
Tested-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Depending on the implementation, the scheduled scan may not give results
quickly when in DISCONNECTED state. This patch resets
wpa_s::normal_scans upon entering to the INTERFACE_DISABLED state so a
normal scan is assured upon going to DISCONNECTED state after the
interface has been re-enabled. This mainly solves a long reconnect time
observed upon repeated kernel driver reloads, i.e., third reload
resulted in a scheduled scan.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-hostap: Arend van Spriel <arend@broadcom.com>
Since wlantest is a separate process that is not synchronized with rest
of the test components, there can be some latency in it having the STA
entries and counters updated. There is a race condition between this
happening and then test script clearing or fetching data. Make this race
condition less likely to cause bogus test failures by adding some wait
between these operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
In addition to running the FLUSH command again, the pending monitor
interface events need be cleared in case the driver was running a scan
when reset() is called. This avoids issues, e.g., with discovery_dev_id
failing due to an unexpected P2P-DEVICE-FOUND event that was generated
by the pending scan operation that had not yet complete when the first
dump_monitor() call in reset() happened.
Signed-hostap: Jouni Malinen <j@w1.fi>
The information of the peer's supported channel and operating class
is required for the driver to do TDLS off channel operations with a
compatible peer. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The vm-config in the subdirectory is less useful as it
will get removed by "git clean" and similar, so read a
config file from ~/.wpas-vm-config in addition.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we already know the SSID of the P2P group we are trying to join, use
that SSID to limit scan responses and BSS selection since we do not
really look for any other network in this case. In addition, this can
fix cases where the peer has just changed its SSID (e.g., started a new
group) and there may be multiple BSS entries for the same BSSID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like slow virtual machines may have issues to complete some EAP
authentication cases (e.g., EAP-EKE in ap_ft_eap) within the 10 second
timeout under load. Double the timeout to avoid incorrect test failures.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
