There is no need to trigger new SA Query procedure to check the state of
the connection immediately after having performed such a check. Limit
the impact of burst of unprotected Deauth/Disassoc frames by starting a
new SA Query procedure only once at least 10 seconds has passed from the
previous SA Query that was triggered by reception of an unprotected
disconnection. The first SA Query procedure for each association does
not follow this rule to avoid issues with test cases that expect to see
an SA Query every time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"TDLS_TEARDOWN *" can now be used to tear down the direct links to all
TDLS peers. This is useful for debugging purposes.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
If a link is unreachable, the specification mandates we should send a
teardown packet via the AP with a specific teardown reason. Force this
by first disabling the link and only then sending the teardown packet
for the LOW_ACK event.
Rename the TDLS LOW_ACK event handler to better reflect its purpose.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
This removes number of unnecessary #ifdef CONFIG_P2P blocks from generic
code by hiding the conditional build into p2p_supplicant.h with empty
inline functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
Performing a P2P Device flow such as p2p_listen or
p2p_find, can degrade the performance of an active interface
connection, if the listen frequency is different than the
frequency used by that interface.
To reduce the effect of P2P Device flows on other interfaces,
try changing the listen channel of the P2P Device to match the
operating channel of one of the other active interfaces. This change
will be possible only in case that the listen channel is not forced
externally, and will be delayed to a point where the P2P Device
state machine is idle.
The optimization can be configured in the configuration file and
is disabled by default.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
In case there is no preference for the GO operating channel,
try using one of 1, 6, 11 (randomly), and only if the random
selection is not suitable traverse all the channels 1..11.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Remove the seperation between getting the local interface frequency and
other interfaces frequencies since going over all the radio interfaces
includes the local interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When the number of frequencies supported by the kernel is bigger than
one, and there is a need to pick a frequency for a new flow such as P2P
GO Negotiation or P2P Invitation, the flow should be able to pick the
best frequency among all the frequencies currently used by the device.
In order to prioritize between the currently used frequencies, add
the ability to collect additional data about each used frequency
(if the frequency is used by a station interface or P2P Client)
and when needed select the best frequency, where:
1. Infrastructure interfaces have highest priority
2. P2P Client interfaces have higher priority over AP/GO
interfaces.
The rational is that the frequency of an AP/GO can change while
that of a station interface cannot.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Remove the check for get_radio_name support from
get_shared_radio_freqs_data() since get_radio_name is no longer in use
in this function.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Most of these calls are checked to return success and there is no reason
why these wouldn't, so be more consistent. This addresses CID 62841,
CID 62840, CID 62839, CID 62838, CID 62837, CID 62836.
Signed-off-by: Jouni Malinen <j@w1.fi>
If this chmod() call fails, the global control interface is allowed to
be used since there was no change to its group. Anyway, it can be
helpful to note the error case in debug log instead of silently ignoring
it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit b125c48fce ('P2P: Add wfd_dev_info=
field for device found event') added Wi-Fi Display device info to the
P2P-DEVICE-FOUND events. However, it did not include proper bounds
checking in wifi_display_subelem_hex() and could accept subelements with
invalid length field values. This could result in buffer read overflow
of up to 64 kB and inclusion of heap memory in the local control
interface event and/or process crash due to invalid memory access. Fix
this by checking the validity of the length field before writing a
hexdump of the data.
Signed-off-by: Jouni Malinen <j@w1.fi>
The vendor_ext[i] = NULL setting did not make any sense since
num_vendor_ext should have been used to index the vendor_ext array. The
old code did not do any harm since i >= num_vendor_ext and none of the
already set entries could have been cleared. Anyway, better clean this
by making it skip the setting to NULL similarly to what was already done
in the P2P peer vendor ext getter.
Signed-off-by: Jouni Malinen <j@w1.fi>
The OSEN code path hardcodes number of struct wpa_ie_data items.
However, it did not clear the full structure and some uninitialized
fields could have been used (e.g., ie.mgmt_group_cipher for a debug
print and ie.capabilities for checking MFPC). Fix this by clearing the
ie data before filling in the hardcoded OSEN values.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.
Signed-off-by: Jouni Malinen <j@w1.fi>
There were couple of missing breaks in switch-default (before/after).
While these did not have any noticeable issues due to falling over to
the next step that just exited from the switch statement, it is cleaner
and more robust to have each case use an explicit break.
Signed-off-by: Jouni Malinen <j@w1.fi>
The tmpentry variable was not initialized and
_wpa_dbus_dict_entry_get_byte_array() does not set tmpentry.type, so it
would have been possible for the error path to end up trying to free
unexpected type of an entry or not free the memory at all.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids an incorrect ARRAY_VS_SINGLETON report for a case where a
pointer is taken to the specified field in a frame and not to a single
octet. Bounds checking was already handled separately.
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to an incorrect operation (MOD vs. AND), the code that was supposed
to return an error if the hex string has odd length was not really
reporting any failures. Instead of reporting an error, the invalid
control interface command would have been truncated. This is not an
issue in practice, but better fix the implementation anyway.
Signed-off-by: Jouni Malinen <j@w1.fi>
If a dict would include duplicated items, the parsing code here would
have leaked memory by overwriting old os_strdup() result with the new
one. Fix this by explicitly freeing the previous entry. This addresses
CID 62852, CID 62851, CID 62850, CID 62849, CID 62847, CID 62846.
Signed-off-by: Jouni Malinen <j@w1.fi>
It would have been at least theoretically possible to hit the first
error in the loop and end up jumping to error handling which would call
os_free(value) without the value having been cleared after the os_free()
call at the end of the previous loop iteration.
Signed-off-by: Jouni Malinen <j@w1.fi>
The GAS query TX operation used a fixed wait time of 1000 ms for the
reply. However, it would be possible for the driver to not support this
long remain-on-channel maximum. Limit this wait time based on driver
support, if needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the p2p_find default delay value configurable as
p2p_search_delay parameter through the configuration file (and through
control interface "SET p2p_search_delay <value>" on the P2P management
interface.
This parameter controls the number milliseconds of extra delay that is
added between search iterations when there is a concurrent operation in
progress. This can be used, e.g., p2p_search_delay=100 to make p2p_find
friendlier to concurrent operations by avoiding it from taking 100% of
the radio resources. The default value is the previous default, i.e.,
500 ms. Smaller values can be used to find peers more quickly at the
cost of larger effect to concurrent operations while a larger value
leaves more time for the concurrent operations at the cost of making
device discovery take longer time.
The optional p2p_find delay argument can still be used to override the
search delay for each search operation.
Since the P2P_CONCURRENT_SEARCH_DELAY macro is not used anymore, the
driver specific build parameter for bcmdhd from Android.mk is also
removed. Similar configuration can now be achieved with
p2p_search_delay=0 in the p2p0 interface configuration file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant_event() is required to include the event data for AP mode
events. In theory, a non-AP mode event could be sent here from the
driver wrapper, so reject such event.
Signed-off-by: Jouni Malinen <j@w1.fi>
Prepare for new extended capabilities bits by checking that the local
buffer is large enough to contain all the bits the driver requests. The
existing buffers are large enough to include anything defined until now,
but it would be possible to add more definitions in the future, so
increase them a bit as well to make this more future proof.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of allowing the connection attempt to occur with an unsupported
inner method, check for that explicitly at the time the network block is
added and drop the network if the identified inner method is not
supported.
Signed-off-by: Jouni Malinen <j@w1.fi>
This cannot really be NULL in practice since cred->eap_method would
point to a valid EAP method. Anyway, to avoid false positive from
analyzers, check the pointer explicitly before printing it.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is mainly to keep static analyzers silent since it does not look
like this code path can be reached in practice due to the way
association events are handled and current_ssid is either set before
resched here or the association is rejected. Anyway, if this could be
reached, the wpa_supplicant_set_wpa_none_key() call would end up
dereferencing a NULL pointer, so add an explicit check to make sure that
does not happen.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the offchannel TX frame command was offloaded to the driver in
offchannel_send_action(), we must not send another copy of the frame if
a remain-on-channel event happens to be delivered between this TX
command and the matching TX status event. It was possible for the
duplicated frame to cause problems, e.g., with P2P invitation exchange
if the same Invitation Request frame got sent twice and only the first
one getting accepted by the peer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The dynamically allocated struct wpa_external_work contains the name of
the radio work in the type field and this is used in a debug print
within radio_work_done(). Re-order radio_work_done() and os_free() calls
on couple of paths where the memory was freed before that final user of
the buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_supplicant was giving below error when "CONFIG_MODULE_TESTS=y" and
"CONFIG_P2P=y" are in .config file:
"wpas_module_tests.c:84: undefined reference to `wps_module_tests'"
This error is coming because "CONFIG_WPS=y" is commented out in .config
file but CONFIG_WPS is getting enabled by CONFIG_P2P in Makefile.
Signed-off-by: Amit Khatri <amit.khatri@samsung.com>
For one specific case when running with Interworking enabled the
re-initialisation of the scan timer is missing. This makes auto connect
to a configured network fail.
The case is:
- Interworking credentials available, but do not match
- Auto interworking is enabled (auto_interworking=1)
- Interworking auto select is disabled (i.e., this is from
auto_interworking=1, not from INTERWORKING_SELECT auto)
- No configured (enabled and non blacklisted) networks are present
in scan results list with full match
- Interworking finds matching networks (it does not do full security
policy match)
This patch covers the case and re-initialises the scan timer to allow
search for a suitable network to continue.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
This makes the operations more consistent when going through multiple
persistent group re-invocation sequences in a row. Each invitation needs
to be accepted separately if persistent reconnect is not enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds [DMG] and [PBSS] flags for scan results and BSS table entries
using the IEEE Std 802.11ad-2012 updated definition of the Capability
field.
Signed-off-by: Boris Sorochkin <qca_bsoroc@qca.qualcomm.com>
This patch adds epoll option for the eloop implementation. This can be
selected with the CONFIG_ELOOP_EPOLL=y build option.
[merit]
See Table1.
Table1. comparison table
+--------+--------+-----------+------------+-------------+
| | add fd | remove fd | prepare fd | dispatch fd |
+--------+--------+-----------+------------+-------------+
| select | O(1) | O(1) | O(N) | O(N) |
+--------+--------+-----------+------------+-------------+
| poll | O(1) | O(1) | O(N) | O(N) |
+--------+--------+-----------+------------+-------------+
| epoll | O(1) | O(1) | 0 | O(M) |
+--------+--------+-----------+------------+-------------+
"add fd" is addition of fd by eloop_sock_table_add_sock().
"remove fd" is removal of fd by eloop_sock_table_remove_sock().
"prepare fd" is preparation of fds before wait in eloop_run().
"dispatch fd" is dispatchment of fds by eloop_sock_table_dispatch().
"N" is all watching fds.
"M" is fds which could be dispatched after waiting.
As shown in Table1, epoll option has better performance on "prepare fd" column.
Because select/poll option requires setting fds before every select()/poll().
But epoll_wait() doesn't need it.
And epoll option has also better performance on "dispatch fd" column.
Because select/poll option needs to check all registered fds to find out
dispatchable fds. But epoll option doesn't require checking all registered fds.
Because epoll_wait() returns dispatchable fd set.
So epoll option is effective for GO/AP functionality.
[demerit]
The epoll option requires additional heap memory. In case of P2P GO, it is
about 8K bytes.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The group object is already registered on DBus at that point, thus wpa_s
structure holds its path already.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fixes a minor mistake: the p2p_info structure should be used here
instead of the peer_handler_args one.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These signals delivers an array of key/value pairs, thus declaring those
as it should.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
When there is a pending WPS negotiation for P2P and signal interrupt is
triggered, invalid read occurs in wpas_wps_terminate_pending() if
wpas_p2p_disconnect() removed the interface. Inverting deinit order
solves the issue.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
