In the SME-in-driver case, wpa_supplicant used only the selected SAE
auth_alg value as the trigger for enabling external authentication
support for SAE. This prevented the driver from falling back to full SAE
authentication if PMKSA caching was attempted (Open auth_alg selected)
and the cached PMKID had been dropped.
Enable external auth based on SAE/FT-SAE key_mgmt, rather than doing
this based on SAE auth_alg, so that the driver can go through full SAE
authentication in cases where PMKSA caching is attempted and it fails.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When operating on the 6 GHz band, add 6 GHz Operation Information inside
the HE Operation element and don't publish HT/VHT IEs.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
- Replace HOSTAPD_MODE_IEEE80211AX mode checks with is_6ghz_op_class()
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Add support for new hardware mode for 6 GHz band. 6 GHz operation is
defined in IEEE P802.11ax/D4.3. 6 GHz band adds global operating classes
131-135 that define channels in frequency range from 5940 MHz to 7105
MHz.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
- Remove HOSTAPD_MODE_IEEE80211AX mode
- Replace check for HOSTAPD_MODE_IEEE80211AX with is_6ghz_freq()
- Move center_idx_to_bw_6ghz() to ieee802_11_common.c file
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
This is needed to allow the 6 GHz operating classes to be compared
against the driver support channels since the channel numbers are not
really unique identifiers of a channel even within a single band.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify behavior with sae_pwe configuration values 0..2, i.e., test the
new hash-to-element mechanism for deriving PWE and negotiation for which
method to use.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the AP advertises RSN Extension element, it has to be advertised
consistently in the unprotected (Beacon and Probe Response) and
protected (EAPOL-Key msg 3/4) frames. Verify that this is the case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If hostapd is configured to enable only the hash-to-element version of
SAE PWE derivation (sae_pwe=1), advertise BSS membership selector to
indicate this.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This parameter can be used to specify which PWE derivation mechanism(s)
is enabled. This commit is only introducing the new parameter; actual
use of it will be address in separate commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This parameter can be used to specify which PWE derivation mechanism(s)
is enabled. This commit is only introducing the new parameter; actual
use of it will be address in separate commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These are the defined values/identifiers for SAE hash-to-element
mechanism from IEEE P802.11-REVmd/D3.0.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The initial crypto wrapper implementation for wolfSSL seems to have
included a copy-paste error in crypto_bignum_sub() implementation that
was identical to crypto_bignum_add() while mp_sub() should have been
used instead of mp_add().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The logic for displaying the message about no configuration being
available for the Enrollee was reversed when support for multiple Config
Objects was added. This was supposed to be shown only if the first
Config Object fails (i.e., when no configuration is available); not when
second attempt fails (since the first one had already been successful in
that case).
Fixes: 7eb06a3369 ("DPP2: Allow multiple Config Objects to be build on Configurator")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd is by default waiting STA to send SAE Confirm before sending the
SAE Confirm. This can now be configured with sae_confirm_immediate=1
resulting in hostapd sending out SAE Confirm immediately after sending
SAE Commit.
These are the two different message sequences:
sae_confirm_immediate=0
STA->AP: SAE Commit
AP->STA: SAE Commit
STA->AP: SAE Confirm
AP->STA: SAE Confirm
STA->AP: Association Request
AP->STA: Association Response
sae_confirm_immediate=1
STA->AP: SAE Commit
AP->STA: SAE Commit
AP->STA: SAE Confirm
STA->AP: SAE Confirm
STA->AP: Association Request
AP->STA: Association Response
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
There is no need for #ifdef/#else/#endif construction in
network_fields[] to cover "mode" (which is completely independent of
CONFIG_MESH) or two separate conditional blocks for mesh related network
fields, so move these into a single conditionally included block.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
As part of a connection request, set EDMG parameters for the driver to
use in the association. The EDMG parameters are based on EDMG IE
received from the AP's Probe Response frames, the driver's EDMG
capability, and the EDMG configuration from the configuration.
As part of starting an AP, set EDMG parameters for the driver to use for
AP operation. The EDMG parameters are based on the driver's EDMG
capability and the EDMG configuration from the configuration.
This implementation is limited to CB2 (channel bonding of 2 channels)
and the bonded channels must be adjacent, i.e., the supported values for
edmg_channel are 9..13.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Add two new configuration parameters for wpa_supplicant:
enable_edmg: Enable EDMG capability for STA/AP mode
edmg_channel: Configure channel bonding. In AP mode it defines the EDMG
channel to start the AP on. In STA mode it defines the EDMG channel to
use for connection.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Add two new configuration parameters for hostapd:
enable_edmg: Enable EDMG capability for AP mode in the 60 GHz band
edmg_channel: Configure channel bonding for AP mode in the 60 GHz band
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
IEEE P802.11ay defines Enhanced Directional Multi-Gigabit (EDMG) STA and
AP which allow channel bonding of 2 channels and more.
nl80211 provides the driver's EDMG capabilities from the kernel
using two new attributes:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represents the channel bandwidth
configurations supported by the driver.
The driver's EDMG capabilities are stored inside struct hostapd_hw_modes.
As part of the connect request and starting AP, EDMG parameters are
passed as part of struct hostapd_freq_params.
The EDMG parameters are sent to the kernel by using two new attributes:
NL80211_ATTR_WIPHY_EDMG_CHANNEL and NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
which specify channel and bandwidth configuration for the driver to use.
This implementation is limited to CB2 (channel bonding of 2 channels)
and the bonded channels must be adjacent.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>