The last beacon report indication was set in all the beacon report
elements in the last frame of the beacon report, while it should be set
only in the last beacon report element of the last frame. This is now
fixed in wpa_supplicant, so update the test case expectation to match
the fixed behavior.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The last beacon report indication was set in all the beacon report
elements in the last frame of the beacon report, while it should be
set only in the last beacon report element of the last frame.
Fixes: ecef0687dc ("RRM: Support for Last Beacon Report Indication subelement")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Help the user be aware of the options to configure when
wpa_supplicant will remove a BSS due to expiration.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The change to python3 broke trace-cmd recording, two
strings need to be bytes instead. Fix that.
Also add a flush() that seems to be needed now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The external authentication command and event does not need to copy the
BSSID/SSID values into struct external_auth since those values are used
before returning from the call. Simplify this by using const u8 * to
external data instead of the array with a copy of the external data.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend commit 5ff39c1380 ("SAE: Support external authentication
offload for driver-SME cases") to support external authentication
with drivers that implement AP SME by notifying the status of
SAE authentication to the driver after SAE handshake as the
driver acts as a pass through for the SAE Authentication frames.
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
This extends driver interface to nl80211 by introducing the following
changes,
1. Register for Authenication frames in driver-based AP SME mode.
2. Advertise NL80211_ATTR_EXTERNAL_AUTH_SUPPORT in set_ap when
offloaded SAE authentication is supported.
3. Extend the NL80211_CMD_EXTERNAL_AUTH interface to also send PMKID
so that the drivers can respond to the PMKSA cached connection
attempts from the stations avoiding the need to contact user space
for all PMKID-based connections.
4. Send external auth status to driver only if it is a driver based
SME solution.
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
beacon_set_done did not get reset to zero on disabling interface using
DISABLE control interface command and the subsequent ENABLE command will
caused configuration of Beacon/Probe Response/Association Response frame
IEs twice. The unnecessary two step configuration can be avoided by
resetting beacon_set_done on DISABLE so that ENABLE can bring up the
interface in a single step with fully updated IEs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Binary presentations of element and scalar can be written directly to
the allocated commit message buffer instead of having to first write
them into temporary buffers just to copy them to the actual message
buffer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
RFC 5931 has these conditions as MUST requirements, so better follow
them explicitly even if the rand,mask == 0 or rand+mask == 0 or 1 cases
are very unlikely to occur in practice while generating random values
locally.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds an explicit check for 0 < x,y < prime based on RFC 5931,
2.8.5.2.2 requirement. The earlier checks might have covered this
implicitly, but it is safer to avoid any dependency on implicit checks
and specific crypto library behavior. (CVE-2019-9498 and CVE-2019-9499)
Furthermore, this moves the EAP-pwd element and scalar parsing and
validation steps into shared helper functions so that there is no need
to maintain two separate copies of this common functionality between the
server and peer implementations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When processing an EAP-pwd Commit frame, the server's scalar and element
(elliptic curve point) were not validated. This allowed an adversary to
bypass authentication, and act as a rogue Access Point (AP) if the
crypto implementation did not verify the validity of the EC point.
Fix this vulnerability by assuring the received scalar lies within the
valid range, and by checking that the received element is not the point
at infinity and lies on the elliptic curve being used. (CVE-2019-9499)
The vulnerability is only exploitable if OpenSSL version 1.0.2 or lower
is used, or if LibreSSL or wolfssl is used. Newer versions of OpenSSL
(and also BoringSSL) implicitly validate the elliptic curve point in
EC_POINT_set_affine_coordinates_GFp(), preventing the attack.
Signed-off-by: Mathy Vanhoef <mathy.vanhoef@nyu.edu>
When processing an EAP-pwd Commit frame, verify that the peer's scalar
and elliptic curve element differ from the one sent by the server. This
prevents reflection attacks where the adversary reflects the scalar and
element sent by the server. (CVE-2019-9497)
The vulnerability allows an adversary to complete the EAP-pwd handshake
as any user. However, the adversary does not learn the negotiated
session key, meaning the subsequent 4-way handshake would fail. As a
result, this cannot be abused to bypass authentication unless EAP-pwd is
used in non-WLAN cases without any following key exchange that would
require the attacker to learn the MSK.
Signed-off-by: Mathy Vanhoef <mathy.vanhoef@nyu.edu>
When processing an EAP-pwd Commit frame, the peer's scalar and element
(elliptic curve point) were not validated. This allowed an adversary to
bypass authentication, and impersonate any user if the crypto
implementation did not verify the validity of the EC point.
Fix this vulnerability by assuring the received scalar lies within the
valid range, and by checking that the received element is not the point
at infinity and lies on the elliptic curve being used. (CVE-2019-9498)
The vulnerability is only exploitable if OpenSSL version 1.0.2 or lower
is used, or if LibreSSL or wolfssl is used. Newer versions of OpenSSL
(and also BoringSSL) implicitly validate the elliptic curve point in
EC_POINT_set_affine_coordinates_GFp(), preventing the attack.
Signed-off-by: Mathy Vanhoef <mathy.vanhoef@nyu.edu>
Explicitly verify that own and peer commit scalar/element are available
when trying to check SAE confirm message. It could have been possible to
hit a NULL pointer dereference if the peer element could not have been
parsed. (CVE-2019-9496)
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Try to avoid showing externally visible timing or memory access
differences regardless of whether the derived pwd-value is smaller than
the group prime.
This is related to CVE-2019-9494.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is an initial step towards making the FFC case use strictly
constant time operations similarly to the ECC case.
sae_test_pwd_seed_ffc() does not yet have constant time behavior,
though.
This is related to CVE-2019-9494.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These groups have significant probability of coming up with pwd-value
that is equal or greater than the prime and as such, need for going
through the PWE derivation loop multiple times. This can result in
sufficient timing different to allow an external observer to determine
how many rounds are needed and that can leak information about the used
password.
Force at least 40 loop rounds for these MODP groups similarly to the ECC
group design to mask timing. This behavior is not described in IEEE Std
802.11-2016 for SAE, but it does not result in different values (i.e.,
only different timing), so such implementation specific countermeasures
can be done without breaking interoperability with other implementation.
Note: These MODP groups 22, 23, and 24 are not considered sufficiently
strong to be used with SAE (or more or less anything else). As such,
they should never be enabled in runtime configuration for any production
use cases. These changes to introduce additional protection to mask
timing is only for completeness of implementation and not an indication
that these groups should be used.
This is related to CVE-2019-9494.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make the non-failure path in the function proceed without branches based
on r_odd and in constant time to minimize risk of observable differences
in timing or cache use. (CVE-2019-9494)
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The QR test result can provide information about the password to an
attacker, so try to minimize differences in how the
sae_test_pwd_seed_ecc() result is used. (CVE-2019-9494)
Use heap memory for the dummy password to allow the same password length
to be used even with long passwords.
Use constant time selection functions to track the real vs. dummy
variables so that the exact same operations can be performed for both QR
test results.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This algorithm could leak information to external observers in form of
timing differences or memory access patterns (cache use). While the
previous implementation had protection against the most visible timing
differences (looping 40 rounds and masking the legendre operation), it
did not protect against memory access patterns between the two possible
code paths in the masking operations. That might be sufficient to allow
an unprivileged process running on the same device to be able to
determine which path is being executed through a cache attack and based
on that, determine information about the used password.
Convert the PWE finding loop to use constant time functions and
identical memory access path without different branches for the QR/QNR
cases to minimize possible side-channel information similarly to the
changes done for SAE authentication. (CVE-2019-9495)
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Get rid of the branches that depend on the result of the Legendre
operation. This is needed to avoid leaking information about different
temporary results in blinding mechanisms.
This is related to CVE-2019-9494 and CVE-2019-9495.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These functions can be used to help implement constant time operations
for various cryptographic operations that must minimize externally
observable differences in processing (both in timing and also in
internal cache use, etc.).
This is related to CVE-2019-9494 and CVE-2019-9495.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This helps in reducing measurable timing differences in operations
involving private information. BoringSSL has removed BN_FLG_CONSTTIME
and expects specific constant time functions to be called instead, so a
bit different approach is needed depending on which library is used.
The main operation that needs protection against side channel attacks is
BN_mod_exp() that depends on private keys (the public key validation
step in crypto_dh_derive_secret() is an exception that can use the
faster version since it does not depend on private keys).
crypto_bignum_div() is currently used only in SAE FFC case with not
safe-prime groups and only with values that do not depend on private
keys, so it is not critical to protect it.
crypto_bignum_inverse() is currently used only in SAE FFC PWE
derivation. The additional protection here is targeting only OpenSSL.
BoringSSL may need conversion to using BN_mod_inverse_blinded().
This is related to CVE-2019-9494 and CVE-2019-9495.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it easier to test various X.509 certificate validation steps
with the server certificate being generated and signed using pyOpenSSL
dynamically.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These wpa_supplicant network profile parameters could be used to specify
a single match string that would be used against the dNSName items in
subjectAltName or CN. There may be use cases where more than one
alternative match string would be useful, so extend these to allow a
semicolon delimited list of values to be used (e.g.,
"example.org;example.com"). If any of the specified values matches any
of the dNSName/CN values in the server certificate, consider the
certificate as meeting this requirement.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Incorrect gen->type value was used to check whether subjectAltName
contained dNSName entries. This resulted in all domain_match and
domain_suffix_match entries failing to find a match and rejecting the
server certificate. Fix this by checking against the correct type
definition for dNSName.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously the EAP user database had to include a wildcard entry for ERP
to work since the keyName-NAI as User-Name in Access-Request would not
be recognized without such wildcard entry (that could point to any EAP
method). This is not ideal, so add a separate check to allow any stored
ERP keyName-NAI to be used for ERP without any requirement for the EAP
user database to contain a matching entry.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
cfg80211 was modified to allow the Multiple BSSID Index element to be
included in the IEs for a nontransmitted BSS. Update the validation step
in this test case to allow that different with the IEs in the Beacon
frame (transmitted BSS).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Inclusion of common/dpp.h into hostapd/main.c brought in an undesired
unconditional dependency on OpenSSL header files even for builds where
DPP is not enabled. Fix this by making the dpp.h contents, and in
particular the inclusion of openssl/x509.h, conditional on CONFIG_DPP.
Fixes: 87d8435cf9 ("DPP: Common configurator/bootstrapping data management")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The rules defining which DH groups are suitable for SAE use were
accepted into IEEE 802.11 REVmd based on this document:
https://mentor.ieee.org/802.11/dcn/19/11-19-0387-02-000m-addressing-some-sae-comments.docx
Enforce those rules in production builds of wpa_supplicant and hostapd.
CONFIG_TESTING_OPTIONS=y builds can still be used to select any o the
implemented groups to maintain testing coverage.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reduce testing dependency on the unsuitable groups so that a test case
against a production build would not fail the test case unnecessarily.
This is in preparation of making production builds
(CONFIG_TESTING_OPTIONS not defined) of wpa_supplicant hostapd disable
all DH groups that have been indicated as being unsuitable.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
identity_buf may be NULL here. Handle this case explicitly by printing
"N/A" instead relying on snprintf converting this to "(null)" or some
other value based on unexpected NULL pointer.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case of connection attempt failure, set 'normal_scans'
to zero, as otherwise it is possible that scheduled scan
would be used and not normal scan, which might delay the
next connection attempt.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
FLUSH should be done on P2P device interface, otherwise the networks are
not removed. Fix that.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Very short beacon intervals can be useful for certain scenarios such
as minimising association time on PBSSs. Linux supports a minimum of
10[1] so let's reduce the minimum to match that.
[1] https://elixir.bootlin.com/linux/latest/ident/cfg80211_validate_beacon_int
Signed-off-by: Brendan Jackman <brendan.jackman@bluwireless.co.uk>
Properly handle the case where OWE IE is allocated, but
there is no space left to add it in the WPA IE buffer.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
While commit 1c156e783d ("Fixed tls_prf() to handle keys with
odd length") added support for keys with odd length, the function
never reached this code as the function would return earlier in
case the key length was odd. Fix this by removing the first check
for the key length.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
