Commit graph

18 commits

Author SHA1 Message Date
Jonathan Afek
e2f3f0232f tests: Use 10 retries for over-the-air broadcast connectivity
The regular hwsim tests use both unicast and broadcast frames to test
the connectivity between 2 interfaces. For real hardware (remote hwsim
tests) the broadcast frames will sometimes not be seen by all connected
stations since they can be in low power mode during DTIM or because
broadcast frames are not ACKed. Use 10 retries for broadcast
connectivity tests for real hardware so that the test will pass if we
successfully received at least one of them.

Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
2016-05-28 16:33:41 +03:00
Johannes Berg
d0007ac9d7 tests: Add test to check disconnect in powersave
The kernel had two bugs (one in hwsim and one more important one in
mac80211) in this area, add a test to make sure we can disconnect
without any kernel issues while in powersave.

Also make sure that the TIM bit gets set and cleared again (by checking
with tshark.)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-02-21 16:07:52 +02:00
Jouni Malinen
f77d6d4bd8 tests: Mesh authentication failure events
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:25:35 +02:00
Jouni Malinen
6d930a1eef tests: Optimize ap_qosmap test cases
Avoid unnecessary DATA_TEST_CONFIG calls and wlantest_cli invocations to
speed up the test cases. This drops ap_qosmap execution time from about
14 seconds to under 3 seconds.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-23 17:46:34 +02:00
Jouni Malinen
1d0b5a04e6 tests: Dump monitor messages before hwsim_utils test
This may be needed in some corner cases where broadcast frames with two
associated stations are received by both devices.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-18 16:41:40 +02:00
Jouni Malinen
1131a1c8d2 tests: Replace last remaining hwsim_test uses with DATA_TEST
External tool is not needed anymore to run the data connectivity tests
since hostapd test mode now allows the possible bridge or VLAN interface
to be specified.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 14:09:07 +02:00
Jouni Malinen
ce9c8c4097 tests: Use internal DATA_TEST_* functionality instead of hwsim_test
This replaces use of the external hwsim_test tool for most data
connectivity test cases. Only the cases where a special interface
(bridge/VLAN) is used are still executed through hwsim_test.

The internal DATA_TEST_* functionality makes it easier to extend the
connectivity test cases through an external device with real WLAN
hardware instead of the hwsim test setup. In addition, the error reports
from this code can be made more informative.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-19 22:27:37 +03:00
Jouni Malinen
a8375c94c0 tests: Pass wpas/hapd instance to test_connectivity()
This makes it easier to replace data connectivity testing to use
something else than local hwsim_test binary on the controller device.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-19 17:54:49 +03:00
Jouni Malinen
8a9a3b34dd tests: WDS STA mode
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-15 19:04:31 +02:00
Jouni Malinen
5be9dcbb86 tests: Remove unnecessary interpreter line from most python files
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-02-21 20:21:53 +02:00
Jouni Malinen
65249f6c4a tests: Verify QoS Mapping results in Data frames
This verifies that IP packets with various DSCP values are mapped to the
correct TID both with default mapping and with custom QoS mappings.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-24 20:21:58 +02:00
Jouni Malinen
c9aa430896 tests: Split run-tests.py logger info into per test case files
The run-tests.py -l argument does not take an argument value anymore.
Instead, debug output is directed to a separate file <test>.log for each
test case.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 12:51:08 +02:00
Jouni Malinen
b162675fd9 tests: Add test cases for per-STA PSK in P2P group
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-09-01 21:35:10 +03:00
Jouni Malinen
3ed2814a1e tests: Use logger.info() instead of print to get one stream
print and logger.info() were directing output to different locations
(stdout and stderr, respectively) which resulted in buildbot showing
reordered entries. Use logger consistently to avoid that.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-08-24 19:48:04 +03:00
Jouni Malinen
280cd8a9a2 tests: Allow hwsim_test and wlantest_cli to be used from PATH
This makes it easier to support some test environments where the
repository is shared between hosts.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-05-11 11:34:49 +03:00
Jouni Malinen
81266da728 tests: Add initial AP tests with hostapd
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-03-27 14:29:01 +02:00
Jouni Malinen
f3f8ee882f tests: Add support for separate P2P group interfaces
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-03-09 17:34:08 +02:00
Jouni Malinen
a311c61dd6 tests: Add test execution mechanism
run-p2p-tests.py can now be used to run all P2P test cases. The
actual test cases are defined in test_p2p_*.py files.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-03-02 12:55:07 +02:00