This could fail in theory if running out of memory, so better check for
this explicitly instead of allowing the exchange to continue and fail
later due to checkcode mismatch.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add test cases that check preCAC, which is available for EU regulatory
domain. Also confirm that preCAC is not used for US.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Add option to:
- add a new AP on the same phy that the backhaul-sta uses
- run CSA from the parent
Adding a new AP (backhaul/fronthaul) on the same phy we have for
backhaul-sta is closer to the real repeater implementation.
Add a test case for that and run CSA.
This is a common problem when we have on the same phy:
- connected backhaul STA
- we started fronthaul/backhaul AP
- we receive (from parent) CSA on the STA interface
This is multi_ap_wps_shared_apdev_csa test case, which fails today with
both mac80211_hwsim and ath9k. To avoid always failing test cases,
ignore this failure for now. Full validation can be enabled once the
issue behind this is fixed.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Pass the backhaul parameters as a parameter. This is in preparation for
channel switch test for Multi AP.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
This test first configure hostapd with an initial SSID
('test-wpa2-psk-start'). Then a new SSID is configured
('test-wpa2-psk-new') using SET and RELOAD. Next, a station is
associated using WPS, and the test verifies that the new SSID was served
to the station.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
cfg80211 may ignore user hints while there are active COUNTRY_IE hints,
thus at some timings it may ignore the country setting back to world
domain. Fix it by making sure the country is set only after all the
interfaces are stopped. In addition, call a more robust
clear_regdom_dev() function.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Test that if notify_mgmt_frames is enabled and a station connects we do
get AP-MGMT-FRAME-RECEIVED, and that it includes an Authentication
frame.
Also test that if notify_mgmt_frames is disabled, no Management frame is
sent on ctrl_iface when a station connects.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
The P2P group may be originally formed on UNII-3, so disabling UNII-1
and UNII-2 will not result in a channel switch failing the test.
Fix this by setting 44 as a preferred channel.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The test configures ft_r0_key_lifetime parameter, however ft_params
already contain the r0_key_lifetime. Since both options are accepted by
hostapd and set the same field, one of them gets overwritten.
As the dictionary enumeration order is not guaranteed in python, the
test may sporadically fail.
Fix that by explicitely removing the unneeded parameter.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Kernel commit 14486c82612a ("rfkill: add a reason to the HW rfkill
state") added an extra byte to the end of the rfkill events and that
confused the read loop here since python tried to buffer the results
from multiple read() calls into the local buffer that then delivered the
extra octets in consecutive events. Fix this by disabling buffering for
these reads.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Python enumerates dictionaries in an arbitrary order, thus the resulting
configuration file will have the parameters shuffled randomly. This may
cause the test to fail when, for example, auth_server_addr is placed
after auth_server_port. Fix this by enforcing some of the fields to be
placed before the others.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Now that wpa_supplicant ignores the unexpected association event in
disconnected-not-trying-to-connect state, this test cases needs to be
modified to avoid incorrect failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The function name for adding frequency lists changed, so this test case
needs a matching change to avoid failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This was broken in the kernel in mac80211 for a while, until commit
780a8c9efc65 ("mac80211: do not disable HE if HT is missing on 2.4 GHz")
fixed it.
Add a test for wifi generation on 2.4 GHz in addition to the 5 GHz one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow to run local/remote process like:
- ubus listen
- logread -f
- tail -f
- wpa_cli
- hostapd_cli
And next wait for specific event(s).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Sweden now allows channel 149 in the updated wireless-regdb. Choose
Japan for the negative test instead.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Add a test which uses a DFS channel, waits for CAC afterwards successful
mesh join and then triggers a radar event and checks if the mesh comes
up again on the same device.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Update ap_wpa2_psk_supp_proto_too_long_gtk_in_group_msg to accept
upcoming change in the parsing validation step that catches the issue.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is in preparation for an implementation change that ends up
contradicting the operations enforced in this test case for mesh coex.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
mesh_open_vht_160 might fail with this message:
---------------
wlan0: Country code not reset back to 00: is ZA
wlan0: Country code cleared back to 00
---------------
This patch fixes the issue.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
wpas_mesh_open_vht_80p80 might fail with this message:
---------------
wlan0: Country code not reset back to 00: is US
wlan0: Country code cleared back to 00
---------------
This patch fixes the issue.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
wpas_mesh_open_vht20 might fails with this message:
---------------
wlan0: Country code not reset back to 00: is US
wlan0: Country code cleared back to 00
---------------
This patch fixes the issue.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
wpas_mesh_open_vht40 might fail with this message:
---------------
wlan0: Country code not reset back to 00: is US
wlan0: Country code cleared back to 00
---------------
This patch fixes the issue.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
wpas_mesh_open_ht40 might fail with this message:
---------------
wlan0: Country code not reset back to 00: is US
wlan0: Country code cleared back to 00
---------------
This patch fixes the issue.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
wpas_mesh_open_5ghz might fail with this message:
---------------
wlan0: Country code not reset back to 00: is US
wlan0: Country code cleared back to 00
---------------
This patch fixes the issue.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
mesh_secure_ocv_mix_legacy might fail with this message:
---------------
wlan0: Country code not reset back to 00: is AZ
wlan0: Country code cleared back to 00
---------------
This patch fixes the issue.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
If the .config file is already identical, avoid copying it even if -f
was specified; this improves build time if nothing has changed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the build artifacts are now landing in distinct directories, we
don't need to 'make clean' and save some rebuild time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This likely passes today (at least without ASAN), but without the next
commit, it trips up a use-after-free bug, which ASAN can catch.
So consider this a regression test.
Signed-off-by: Brian Norris <briannorris@chromium.org>
The blacklist design will be modified in the following commits and that
would result in this validation step based on the older implementation
starting to fail. Remove this check to avoid such testing failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
Remove this part of the dbus_network test case since it would be causing
failures after wpa_supplicant is modified to accept empty strings
through D-Bus.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is mainly for standalone monitor in case we know and would like to
setup specific monitor configuration.
-m monitor:<chan>,<bw>, <cf1>, <cf2>:...
For example:
-m monitor:1,40,3,0
-m e4300:1,40,3,0:11,40,9,0
This also supports monitor with multiple interfaces (one pcap).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Before we have to kill an application we start in the thread - in most
cases using killall and sometimes kill other applicantions, e.g., tcpdump,
iper, iperf3, tshark.
With this patch we are able to stop/kill a single application/thread
instead, based on the pid file.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
In case we are using ssh MUX (which speed up a lot test execution) with
remotehost we could hit cases where ssh will hang up. This depends on
different ssh versions and remotehost implementation.
stderr as a tmpfile fixes this problem.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
This is needed to allow the test cases to work on systems using
secpolicy=2 default (e.g., Ubuntu 20.04).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update the SAE-PK implementation to match the changes in the protocol
design:
- allow only Sec values 3 and 5 and encode this as a single bit field
with multiple copies
- add a checksum character
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Instead of overriding the subject field with something arbitrary, use
the value that is included in the CSR now that there is something there.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The parsed 'length' field might pointsbeyond the end of the frame, for
some malformed frames. I haven't figured the source of said packets (I'm
using kernel 4.14.177, FWIW), but we can at least be safer about our
handling of them here.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Instead of checking if the kernel allows modules (via the presence of
/proc/modules), check if mac80211_hwsim is already there and load it
only if not. This gets rid of some ugly prints from modprobe in case
code isn't even a module and cannot be found, etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With python3 bytes are returned for stdout, so need to use b''
strings instead of normal strings. These are just a few places
I ran into, almost certainly more places need it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we want the test to actually use 160/80+80 we need to explicitly
advertise that we support it ourselves, since the kernel is going to be
a bit more strict about this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clear scan results explicitly in test cases that check BSS entry flags
to avoid incorrect failures based on results from earlier test cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Lambda >= 12 is needed with Sec = 2, so drop the shorter password
lengths in the sae_pk and module_wpa_supplicant test cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Now that there is a pending mac80211 patch ("mac80211: allow SA-QUERY
processing in userspace") to allow wpa_supplicant to take care of SA
Query Request processing, start enforcing correct behavior for this in
ocv_sa_query and wpa2_ocv_sta_override_sa_query_resp.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the current country code cannot be fetched, do not try to report the
current value in the log since that will result in TypeError exception.
Signed-off-by: Jouni Malinen <j@w1.fi>
