Commit graph

913 commits

Author SHA1 Message Date
Ardong Chen
2f9929ffcc WPS: Allow pending WPS operation to be cancelled
A new ctrl_interface command, WPS_CANCEL, can now be used to cancel
a pending or ongoing WPS operation. For now, this is only available
with wpa_supplicant (either in station or AP mode). Similar
functionality should be added for hostapd, too.
2010-09-10 10:30:25 -07:00
Ardong Chen
014732ea81 WPS: Fix timeout event to be sent over ctrl_interface
This was supposed to be sent to external event monitors, i.e., to
use wpa_msg instead of wpa_printf.
2010-09-10 10:30:25 -07:00
Wei-Jen Lin
c0a321c519 Allow bssid parameter to be cleared through ctrl_interface
Setting bssid to an empty string, "", or any can now be used to
clear the bssid_set flag in a network block, i.e., to remove bssid
filtering.
2010-09-10 10:30:25 -07:00
Ardong Chen
876103dc6c wpa_cli action: Add WPS_EVENT_SUCCESS and WPS_EVENT_FAIL handlers 2010-09-10 10:30:25 -07:00
Ardong Chen
c481048f7c P2P: Add frequency into group started ctrl_interface events 2010-09-10 10:30:25 -07:00
Jouni Malinen
812bf56ab1 Fix build without CONFIG_P2P=y 2010-09-09 07:20:28 -07:00
Jouni Malinen
e9a7ae41fa P2P: Use SSID from GO Negotiation to limit WPS provisioning step
In order to avoid picking incorrect SSID from old scan results, use
SSID from GO Negotiation to select the AP.
2010-09-09 07:17:23 -07:00
Jouni Malinen
743ef79914 P2P: Deinit GO group data before global P2P deinit
This avoids issues with using freed memory in p2p_group_deinit().
2010-09-09 07:17:23 -07:00
Jouni Malinen
f8d0131a11 P2P: Use operating frequency from peer table as backup for join
The scan operation before Provision Discovery Request may not include
the GO. However, we are likely to have the GO in our P2P peer table,
so use that information to figure out the operating channel if BSS
table entry is not available.
2010-09-09 07:17:23 -07:00
Jouni Malinen
a482883f63 P2P: Fix connect-to-running-group if Action TX status is delayed
The following operations (scan and associate) were not run if the
Provisioning Discovery Response is received before the TX Action
status.
2010-09-09 07:17:23 -07:00
Jouni Malinen
ab218b7c72 P2P: Add some more debug information for Action frame TX 2010-09-09 07:17:22 -07:00
Jouni Malinen
1cc3a29d49 P2P: Clear pending Action TX frame on p2p_stop_find and p2p_listen
This is needed to avoid issues with the previous TX command from
stopping long Listen state.
2010-09-09 07:17:22 -07:00
Jouni Malinen
b6c79a998f Add test command for disabling/enabling A-MPDU aggregation
ctrl_iface command "SET ampdu <0/1>" can now be used to
disable/enable A-MPDU aggregation.
2010-09-09 07:17:21 -07:00
Jouni Malinen
10b9ac17cf P2P: For now, do not use channels 12-14 in P2P groups
This is needed to make sure we do not try to accidentally enable GO
in channels that may not be allowed. In addition, this may help with
some driver that do not like channel 14 even as a passive scan
channel.
2010-09-09 07:17:21 -07:00
Jouni Malinen
7fbf99aa6b P2P: Add an example p2p-action script for udhcpc/udhcpd 2010-09-09 07:17:21 -07:00
Jouni Malinen
56815b2b7d Copy WPS strings into AP configuration when using wpa_supplicant AP 2010-09-09 07:17:21 -07:00
Jouni Malinen
1c9cb49fe9 Trigger WPS configuration update on string changes
Previously, only Device Name string was handled, but similar trigger
is needed on Manufacturer, Model Name, Model Number, and Serial Number
changes.
2010-09-09 07:17:21 -07:00
Jouni Malinen
0e14267a31 P2P: Avoid segfault on AP deinit after failed AP start 2010-09-09 07:17:21 -07:00
Jouni Malinen
e1f1509bb0 P2P: Fix P2P IE generation for AssocReq when BSS info is not available
This code could segfault on NULL pointer dereference at least when
ap_scan=2 is used.
2010-09-09 07:17:21 -07:00
Jouni Malinen
c4ea4c5c90 P2P: Allow driver wrapper to indicate how many stations are supported
This can be used to limit the number of clients allowed to connect
to the group on the GO.
2010-09-09 07:17:21 -07:00
Jouni Malinen
f80a2237ca Fix AP mode wps_pin command to return the entered PIN
This command is supposed to return the PIN value that was generated
or passed in as an argument. In the AP case, the entered PIN was not
being returned.
2010-09-09 07:17:21 -07:00
Jouni Malinen
eea2fd9eff P2P: Add mechanism for configuring UAPSD parameters for group
This is needed to be able to change parameters for dynamically
created interfaces between the creation of the interface and
association/start AP commands.

Following ctrl_interface commands can now be used:

P2P_SET client_apsd disable
- disable configuration (i.e., use driver default) in client mode

P2P_SET client_apsd <BE>,<BK>,<VI>,<VO>;<max SP Length>
- enable UASPD with specific trigger configuration (0/1) per AC
  (max SP Length is currently ignored)

P2P_SET go_apsd disable
- disable configuration (i.e., use driver default) in AP mode

P2P_SET go_apsd <0/1>
- disable/enable APSD in AP mode
2010-09-09 07:17:21 -07:00
Jouni Malinen
3dfda83d9c P2P: Add Device Password ID to GO Neg Request RX event
This event indicates the Device Password ID that the peer tried
to use in GO Negotiation. For example:
P2P-GO-NEG-REQUEST 02:40:61:c2:f3:b7 dev_passwd_id=4
2010-09-09 07:17:20 -07:00
Jouni Malinen
4147a2cc64 P2P: Fix p2p_connect join with interface address
Need to fetch P2P Device Address from the peers table in case the
p2p_connect join command uses interface address.
2010-09-09 07:17:20 -07:00
Jouni Malinen
72044390f3 P2P: Add support for cross connection
If enabled, cross connection allows GO to forward IPv4 packets
using masquerading NAT from the P2P clients in the group to an
uplink WLAN connection. This is disabled by default and can be
enabled with "wpa_cli p2p_set cross_connect 1" on the P2P device
interface.
2010-09-09 07:17:20 -07:00
Jouni Malinen
aefb53bd5d P2P: Disable periodic NoA when non-P2P STA is connected
For now, this applies to the test command that can be used to set
periodic NoA (p2p_set noa). The value are stored and periodic NoA
is enabled whenever there are no non-P2P STAs connected to the GO.
2010-09-09 07:17:20 -07:00
Jouni Malinen
4c08c0bd57 P2P: Include P2P IE in (Re)AssocReq to infra AP if it uses P2P IE
While this is not strictly speaking required by the P2P specification
for a not-P2P Managed Device, this can provide useful information for
the P2P manager AP and may be needed to pass certification tests.
2010-09-09 07:17:20 -07:00
Jouni Malinen
43a3863516 Trigger scan on reload-config only if there are enabled networks 2010-09-09 07:17:20 -07:00
Jouni Malinen
d9d6a58c8f P2P: Fix invitation to active group to use correct operating channel
Invitation Request must use the current operating frequency of the
group, not the default operating channel.
2010-09-09 07:17:20 -07:00
Jouni Malinen
dcf788d1a4 WPS: Fix configuration strings on config reload
Previously, freed memory could be used as device name (and other similar
parameters) when building WPS IE after SIGHUP.
2010-09-09 07:17:20 -07:00
Jouni Malinen
af8ab1ae97 P2P: Use 'Enrollee info' WPS request type in P2P scans
This avoids setting explicit Request-to-Enrollee request when
WPS 2.0 is used.
2010-09-09 07:17:20 -07:00
Jouni Malinen
131cb37c2d P2P: Allow pre-authorization of invitation to apply to src addr
For client-invites-device case, the pre-authorization of an invitation
to running group will need to allow Invitation Request from specified
address, too. This is for testing uses only.
2010-09-09 07:17:19 -07:00
Jouni Malinen
6d4747a9a2 Add P2P Interface Address into ctrl_iface status output 2010-09-09 07:17:19 -07:00
Jouni Malinen
80c9582a5f P2P: Add test command for filtering which peers are discovered
"wpa_cli p2p_set peer_filter <MAC address>" can now be used to
only allow a single P2P Device (based on P2P Device Address) to be
discovered for testing. Setting the address to 00:00:00:00:00:00
disables the filter.
2010-09-09 07:17:19 -07:00
Jouni Malinen
6e6963ea86 P2P: Add test mode for SD to force fragmented response 2010-09-09 07:17:19 -07:00
Jouni Malinen
18708aadfc P2P: Initial support for SD fragmentation (GAS Comeback Request/Response) 2010-09-09 07:17:19 -07:00
Jouni Malinen
2a43101e48 P2P: Fix memory leak in SD service entries
Need to flush stored service entries when wpa_supplicant is being
terminated.
2010-09-09 07:17:19 -07:00
Jouni Malinen
bf608cad56 P2P: Rename SD info not available define to match with spec change 2010-09-09 07:17:19 -07:00
Jouni Malinen
706887fc28 P2P: Stop early when processing not-persistent invitation result 2010-09-09 07:17:19 -07:00
Jouni Malinen
2e062d5d74 P2P: Fix Group ID in Invitation Request from active GO
Need to get P2P Device Address, not the Interface Address.
2010-09-09 07:17:19 -07:00
Jouni Malinen
108def931e P2P: Add command for pre-authorizing an invitation to an active group
This is mainly designed for testing and allows p2p_connect join auth
to be used to accept a specific invitation to an active group that
may be received in the future.
2010-09-09 07:17:19 -07:00
Jouni Malinen
3c5126a41f P2P: Set Device Password ID in WPS M1/M2 per new rules
If the P2P client (WPS Enrollee) uses a PIN from the GO (Registrar),
Device Password ID in M1 & M2 is set to Registrar-specified.
2010-09-09 07:17:19 -07:00
Jouni Malinen
ef922c4a34 P2P: Run a scan before provision discovery in p2p_connect join
This is needed to make sure we have fresh BSS information for the GO.
2010-09-09 07:17:19 -07:00
Jouni Malinen
c381508d88 P2P: Implement power save configuration
wpa_cli p2p_set ps <0/1/2>
wpa_cli p2p_set oppps <0/1>
wpa_cli p2p_set ctwindow <0..> msec
2010-09-09 07:17:19 -07:00
Jouni Malinen
07a30a66c3 P2P: Do not schedule new remain-on-channel if waiting for drv event
The driver event for remain-on-channel may be delayed in a way that
allows management-frame-received event to be received before
wpa_supplicant knows that the driver is actually already on the
previously requested channel. We should not request a new
remain-on-channel to send a response to just a frame if we are waiting
for the driver to get to the same channel. Instead, just continue
waiting for the driver event.
2010-09-09 07:17:18 -07:00
Jouni Malinen
d6ae995057 P2P: Fix infinite loop on interface selection for Action frame TX
When the first wpa_supplicant interface is not the correct one for
transmitting an Action frame (e.g., P2P Presence Request frame
uses a group interface), the code got stuck in an infinite busy
loop. Fix the iteration to go through the interfaces properly.
2010-09-09 07:17:18 -07:00
Jouni Malinen
df91238b54 P2P: wpa_qui-qt4: Add P2P functionality into the GUI 2010-09-09 07:17:18 -07:00
Jouni Malinen
42f0101b4d P2P: wpa_cli action calls for P2P group started/removed events 2010-09-09 07:17:18 -07:00
Jouni Malinen
57faa1cee8 wpa_cli: Add P2P commands 2010-09-09 07:17:18 -07:00
Jouni Malinen
9fdd0fada7 P2P: Add disassociation/deauthentication IE notifications 2010-09-09 07:17:18 -07:00