This adds support for PS3 wireless to wpa_supplicant.
Although PS3 wireless driver is designed to conform the WEXT standard
as much as possible, unfortunately the wext driver wrapper of
wpa_supplicant can not support PS3 wireless fully because:
- PS3 wireless driver uses private WEXT ioctls for accepting PSK of
WPA-Personal from the userland.
WEXT does not specify the way to do it.
- The association and 4-way handshake are done by PS3 virtual
wireless device. The guest OSes can not interfere it.
- No EAPOL frames are allowed to go outside of the
hypervisor/firmware nor come from. They are eaten by the firmware.
Thus I needed to make a new driver wrapper for PS3 wireless.
This patch can be applied against the latest 0.6.x tree.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Sam Leffler <sam@errno.com>:
Attached are changes from Chris Zimmerman (cc'd) to allow drivers to handle
radius ACL's. The patch is against 0.5.10 but I suspect will also apply to
your latest code. These mods enable radius acl support in freebsd w/ my
vap code.
You may want to do the changes to ieee802_11_auth.c differently as they
currently require all participating drivers to work the same. You might be
able to check the return value from hostapd_set_radius_acl_auth and use
that to decide whether the alternate code should be run so you can have 1
driver using this stuff while the other does not.
(jm: Added without more dynamic check for now; in addition, none of the
current in-tree driver wrappers actually implement these handlers, so this
is in preparation for future changes)
session_timeout and acct_interim_interval set to NULL. Without checking
these before accessing, we'd cause a NULL pointer access in this case. In
ieee802_11.c calls hostapd_allowed_address() with valid pointers.
The old version was using struct wpa_sm::bssid which is not necessarily
updated to point to the correct target address when doing over-the-air FT
since the address is used before the association has actually been
completed.
Transition. This fixes a potential issue where an incorrectly behaving AP
could send a group key update using the old (now invalid after reassociate)
PTK. This could also happen if there is a race condition between reporting
received EAPOL frames and association events.
Need to process EAP AVP after the non-EAP Phase 2 method. In addition,
EAP-TTLS/MSCHAPv2 needs special code for handling the starting of TNC after
extra roundtrip of MSCHAPv2 success message.
Tunneled EAP sequence is now used to perform both the authentication (e.g.,
using EAP-GTC) and TNC validation (EAP-TNC) inside the EAP-FAST tunnel if
TNC has been enabled.
This adds EAP-TNC method and TNCS (IF-IMV and IF-TNCCS) functionality.
There is no integration with EAP-TTLS and EAP-FAST at this point, so this
version is not yet suitable for real use (i.e., EAP-TNC can only be tested
outside a tunnel which is not an allowed configuration for deployment).
However, the basic TNCS functionality is more or less complete and this
version seems to interoperate with wpa_supplicant.
When a WpaMsg item to the QValueList WpaMsgList, there's no constructor
that the QValueList can call. This is a port of the fix from the stable
branch where it builds fine.
Number of TLVs were processed in groups and these cases were now separated
into more flexible processing of one TLV at the time. wpabuf_concat()
function was added to make it easier to concatenate TLVs. EAP Sequences are
now supported in both server and peer code, but the server side is not
enabled by default.
This allows Phase 2 Identity Request to be skipped if the identity is
already known from PAC-Opaque received in TLS handshake in order to save
one roundtrip from normal authentication.
This allows associations to be denied if the STA tries to use too large
listen interval. The default value is 65535 which matches with the field
size limits.
The Debian package checker "lintian" was making noise about
wpa_supplicant.conf(5). It was caused by a line beginning with ', which is
apparently not liked by man(1).
I suggest the use of <emphasis>word</emphasis> where 'word' is used at the
moment.
Signed-off-by: Kel Modderman <kel@otaku42.de>
These are expected in most cases and there is no need to confuse users
with the messages in stderr (perror was used here). These are now only
shown in debug output and EOPNOTSUPP errors are silently ignored.
Jouni Malinen