test_ap_change_ssid verifies that the SET and RELOAD control interface
commands can be used to change the SSID of a hostapd-controlled WPA2-PSK
AP, i.e., for a case where the PSK needs to be derived again after the
SSID change.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reject RELOAD control interface command if the dynamic configuration
changes have resulted into a state where the configuration is invalid.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the configuration validation routines to be called from
src/ap/*.c for runtime updates of configuration without reprocessing the
full configuration file.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This provides a new option for configuring multiple virtual interfaces
(BSS) that share a single radio. The new command line parameter
-b<phyname>:<config file name> is used to define one or more virtual
interfaces for each PHY. The first such entry for a new PHY is used to
initialize the interface structure and all consecutive parameters that
have the same PHY name will be added as virtual BSS entries to that
interface. The radio parameters in the configuration files have to be
identical.
This can be used as an alternative for the bss=<ifname> separator and
multiple BSSes in a single configuration file design while still
allowing hostapd to control the PHY (struct hostapd_iface) as a group of
virtual interfaces (struct hostapd_data) so that common radio operations
like OLBC detection and HT40 co-ex scans can be done only once per real
radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it more convenient to move BSS configuration entries between
struct hostapd_config instances to clean up per-BSS configuration file
design.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This may be needed if the wpa_psk information for previously derived
from passphrase and either the SSID or the passphrase has changed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of duplicating the functionality and missing changes (like the
hostapd_broadcast_wep_clear() call), use the hostapd_clear_old()
function that was already used for the similar case with configuration
file reload.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The test_ap_hs20_username* test cases verify that a username/password
credential can be used for Hotspot 2.0 connection and that the network
type is reported correctly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
test_ap_hs20_ext_sim_roaming is otherwise identical with
test_ap_hs20_ext_sim, but the network is operated by a roaming partner.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that the network type (home/roaming/unknown) is available
and set properly in the test_ap_hs20_ext_sim test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows sp_type={home,roaming,unknown} to be used to determine
network type with SIM-based credentials even if the domain name
parameter is not configured explicitly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit ca9bc5b566 added wpas_conf_ap_vht()
as a static function with the caller within CONFIG_IEEE80211N, but the
function outside. This resulted in a compiler warning for wpa_supplicant
AP/P2P builds when CONFIG_IEEE80211N=y was not used. Fix that by using
matching conditional block around the function.
Signed-hostap: Jouni Malinen <j@w1.fi>
Start GO with VHT support if VHT option was requested
and the appropriate channels are available.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Add the option to ask for VHT operation similarly to the way ht40 is
configured - either by adding 'vht' param to the relevant p2p_*
commands or by configuring p2p_go_vht=1 in the configuration file.
This patch only adds the configuration option (e.g., via control
interface). The actual handling of the VHT parameter (asking the driver
to use VHT, etc.) will be done by the following patch.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Later on, we'll consider the availability of these
channels when starting P2P GO with VHT support.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
In order to support P2P GO with 11ac support, add CONFIG_IEEE80211AC
config option support to the Makefile.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Mask the remote VHT capabilities with our own capabilities, similarly
to what is done for HT capabilities.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Make sure the driver supports 160/80+80 MHz VHT capabilities
before trying to configure these channels.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
VHT_CAP_BEAMFORMEE_STS_MAX, VHT_CAP_SOUNDING_DIMENSION_OFFSET, and
VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT were not defined properly (wrong
name/size). Fix that and update the hostapd.conf parsing accordingly.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Previously the Country element contained the max TX power the local
hardware was capable of. Change this to just use the regulatory limit.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Since the scripts must be run from the source directory to
find the tests to run, they can use a relative path to the
wpaspy module instead of requiring it to be installed.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Both of these variables can result in optimized WPS scans, so better
clear these more consistently to avoid unexpected single-channel scans.
Signed-hostap: Jouni Malinen <j@w1.fi>
This was forgotten from the previous commit which allowed some cases to
trigger single-channel scan incorrectly if an optimized WPS scan had not
yet been completed at the time network selection was started.
Signed-hostap: Jouni Malinen <j@w1.fi>
"run-tests.py -S <db file> -L" can now be used to update a database
table with the current set of test cases and their descriptions.
Signed-hostap: Jouni Malinen <j@w1.fi>
Make sure special optimized scans (like WPS-single-channel or
sched_scan) do not get used during the network selection scan. This
could have been hit in cases where a previous operation has been stopped
in a state where special scan parameters were going to be used.
Signed-hostap: Jouni Malinen <j@w1.fi>
cfg80211 may keep some state (e.g., regulatory domain), so make sure
this gets cleared between each full testing cycle.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new p2p_add_cli_chan=1 configuration parameter can be used to
request passive-scan channels to be included in P2P channel lists for
cases where the local end may become the P2P client in a group. This
allows more options for the peer to use channels, e.g., if the local
device is not aware of its current location and has marked most channels
to require passive scanning.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new p2p_no_go_freq frequency range list (comma-separated list of
min-max frequency ranges in MHz) can now be used to configure channels
on which the local device is not allowed to operate as a GO, but on
which that device can be a P2P Client. These channels are left in the
P2P Channel List in GO Negotiation to allow the peer device to select
one of the channels for the cases where the peer becomes the GO. The
local end will remove these channels from consideration if it becomes
the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When we have CAC active and receive a radar event, we should ignore
CAC_ABORT event and handle channel switch in the radar event handler.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This fixes a problem when operating on non-DFS channel and receiving a
radar event for that channel. Previously, we would have decided to
switch channels.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add a table of available VHT80 channels. This table contains the first
available channel. We will also choose this first channel as the control
one.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
To avoid a problem where the beacon socket occasionally
blocks, mark any sockets on the eloop as non-blocking.
The previous patch reordered the code to never send a
command after a socket was put on the eloop, but now also
invalidate the nl handle pointer while it's on there.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Abstract the handling of sockets on the eloop to avoid
destroying sockets still on the eloop and also to allow
the next patch to mark the socket non-blocking.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The IBSS code registers the bss nl_mgmt socket for auth
frames when the join event happens, but that is too late
as then the socket is already on the eloop, which could
cause problems when other events are received at the
same time as the registration is done.
Move the auth frame registration to the initial setup
before the socket is put onto the eloop.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Some driver wrappers may implement this by writing eight octets even
though IPN is only six octets. Use a separate WPA_KEY_RSC_LEN (8) octet
buffer in the call to make sure there is enough buffer room available
for the full returned value and then copy it to IPN field.
The previous implementation used the following igtk field as the extra
buffer and then initialized that field afterwards, so this change does
not fix any real issue in behavior, but it is cleaner to use an explicit
buffer of the maximum length for get_seqnum().
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_s->conf cannot be NULL because wpa_supplicant_init_iface() would not
allow wpa_supplicant_add_iface() to return wpa_s instance in such state.
Signed-hostap: Jouni Malinen <j@w1.fi>
