P802.11-REVmc clarifies that the Target BSSID field is always present
hen status code is zero, so match that requirement.
Signed-hostap: Jouni Malinen <j@w1.fi>
This commit adds few more debug prints to log the RSSI information from
the scanned BSSIDs and the current connected BSSID when comparing
neighbor results during WNM Transition Management Request processing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, WPS credential provisioning removed duplicated network
entries only if they had identicical SSID, security parameters, and the
keys. However, it is possible that the AP has changes its keys and
leaving the old entry behind can result in connectibity issues (e.g.,
with 4-way handshake failing due to use of the old PSK). Fix this by
allowing the old network entry to be removed even if the keys
(passphrase, PSK, WEP keys) are different.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to enable various testing parameters and
functionality in build configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the AP is expected to be available, there is no need to wait for
the full five second wait between scans during WPS connection. This
speeds up cases where the first scan misses the AP for some reason.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It may not always be desirable to trigger reassociation or network
change based on scan results from externally to wpa_supplicant trigger
scan operations. Skip network selection and roaming determination if the
received scan result is known to be triggered by something external to
wpa_supplicant. The control interface SCAN command can be used to
request wpa_supplicant to determine the best network.
Signed-hostap: Jouni Malinen <j@w1.fi>
This avoids some unnecessary attempts to request the driver to start a
scan while it is still busy with the scan operation that was started by
an external program.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows users of wpa_supplicant control interface to figure out when
their specific scan command has been started and completed. For example:
CTRL-EVENT-SCAN-STARTED
> scan freq=2412,2417 passive=1 use_id=1
3
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-STARTED id=3
CTRL-EVENT-SCAN-RESULTS id=3
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows external programs to request wpa_supplicant to execute
a passive scan (i.e., do not send any Probe Request frames).
Signed-hostap: Jouni Malinen <j@w1.fi>
This parameter was not really used for anything else apart from a debug
message in the same function that set it. In addition, cfg80211 returns
the set of scanned frequencies even for the full scan, so the code that
was setting this conditionally on frequency list not being there was not
really ever entered either.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new freq=<frequency ranges> parameter to the SCAN command can be
used to request a scan to be performed on the specified set of channels
instead of on all channels. For example, "wpa_cli scan
freq=2400-2500,5180" would scan channels 1-14 and 36. Only the channels
that the driver indicates as enabled and that are within the specified
ranges are included in the request.
Signed-hostap: Jouni Malinen <j@w1.fi>
In addition, update build rules to compile object files in the same
directory as the source code file if CONFIG_CODE_COVERAGE=y is set to
make lcov find the source code files.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use an array of ciphers and a loop instead of copy-pasted copies of the
same printing functionality for each cipher.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds initial parts for supporting the new GCMP-256, CCMP-256,
BIP-GMAC-128, BIP-GMAC-256, and BIP-CMAC-256 cipher suites.
Signed-hostap: Jouni Malinen <j@w1.fi>
In wpa_supplicant_terminate_proc(), while iterating and
terminating interfaces, after an interface is terminated,
we can no longer access its memory as it is no longer valid
and causes a crash.
Fix this by saving the pointer to the next interface before freeing
the current one to avoid accessing an invalid memory location.
Signed-hostap: Moshe Benji <moshe.benji@intel.com>
This just serves to check if there was a scan within
the last 5 seconds, hence it should use monotonic time.
While at it, also use os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This is only used for a debug message, but that message prints
the time since the last attempt, so it should use monotonic
time instead of wall clock.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The MMIC failure code should use monotonic time to check
whether 60 seconds have elapsed or not. For type-safety,
use struct os_reltime for the timestamp variable, and
also convert to using os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Temporarily disabled networks are disabled for a certain
duration, so the code should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
GO activation can fail if the first client doesn't connect
within a certain time, but this should not be dependent on
wall time -- use monotonic time instead.
While at it, use os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The reinit detection skips reinit when the time since the own
authentication frame TX is less than half a second, so it shouldn't
be affected by wall time and use monotonic time instead.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The EAPOL RX workaround checks that the events are less than 100 ms
apart, so only uses relative times and should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The bgscan simple and learn algorithms should run regardless
of wall clock time jumps, so make them use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The BSS table, scan timeout, and related functionality should use
monotonic time since they care about relative values (age) only.
Unfortunately, these are all connected, so the patch can't be split
further. Another problem with this is that it changes the driver wrapper
API. Though, it seems only the test driver is using this.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The SA query timeout is just a regular timeout (currently
hard-coded to 1000 TU), so use monotonic time for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
bgscan_learn_get_probe_freq() starts from returning the second entry in
the supp_freqs arrays. Change its logic a bit to make it start from the
first entry.
Signed-hostap: Eliad Peller <eliad@wizery.com>
In case the initial signal level of the associated BSS was above the
given threshold, bgscan_learn module would begin using the
short_interval but never switch to the long_interval as there would be
no signal change event. Make the init code poll for the current signal
level and set scan_interval accordingly. This logic exists in
bgscan_simple but was missing in bgscan_learn.
Signed-hostap: Eyal Shapira <eyal@wizery.com>
Some hw modes (e.g., 11b and 11g) contain the same frequencies,
causing the supp_freqs array to be populated with redundant entries.
Check for the existence of the freq before adding it.
Signed-hostap: Eliad Peller <eliad@wizery.com>
Stopping bgscan on any state other than COMPLETED results
in bgscan reset (stop + start) on every rekeying operation.
Signed-hostap: Eliad Peller <eliad@wizery.com>
Do not assume the driver supports QoS Mapping, but instead, advertise
support for this only if CONFIG_INTERWORKING is defined and driver
indicates support for configuring QoS Map.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 202dec2a94 introduced a never
ending loop for a case where a single wpa_supplicant process is used
with multiple radios. Fix this by advancing the iface pointer properly
to the next interface in the loop until a NULL pointer is hit.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Adds support for VHT by parsing bandwidth and center_freq{1,2}.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Based on priority, remove the connection with least priority whenever
a frequency conflict is detected.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
This field allows adds enough information into the P2P-DEVICE-FOUND
events to figure out if the peer supports Wi-Fi Display.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Allow addition static and shared libraries to be specified from the
eap_proxy_*.mk file for Android build. In addition use $(LOCAL_PATH) as
a prefix for that Android makefile part.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
struct wpa_radio is used as a shared data structure between all struct
wpa_supplicant instances that share the same physical radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
