Add smps_modes field, and let the driver fill it with its supported SMPS
modes (static/dynamic). This will let us start an AP with specific SMPS
mode (e.g., dynamic) that will allow it to reduce its power usage.
Signed-off-by: Eliad Peller <eliad@wizery.com>
The new ext_eapol_frame_io parameter can be used to configure hostapd
and wpa_supplicant to use control interface for receiving and
transmitting EAPOL frames. This makes it easier to implement automated
test cases for protocol testing. This functionality is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use hostapd_freq_params instead of simple frequency parameter for driver
commands. This is preparation for IBSS configuration to allow use of
HT/VHT in IBSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This removes number of unnecessary #ifdef CONFIG_P2P blocks from generic
code by hiding the conditional build into p2p_supplicant.h with empty
inline functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is not much point in building devices with WPS 1.0 only supported
nowadays. As such, there is not sufficient justification for maintaining
extra complexity for the CONFIG_WPS2 build option either. Remove this by
enabling WSC 2.0 support unconditionally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The ieee80211w parameter was not previously copied to the hostapd BSS
structure from wpa_supplicant configuration, so PMF was practically
disabled. Allow it to be configured through the wpa_supplicant network
configuration block.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds an option to optimize AP teardown by leaving the
deletion of keys (including group keys) and stations to the driver.
This optimization option should be used if the driver supports stations
and keys removal when stopping an AP.
For example, the optimization option will always be used for cfg80211
drivers since cfg80211 shall always remove stations and keys when
stopping an AP (in order to support cases where the AP is disabled
without the knowledge of wpa_supplicant/hostapd).
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Since P2P specification mandates P2P GO to support WMM-PS with legacy
STAs, enable this automatically if the driver indicates support for
U-APSD in AP mode. The "P2P_SET go_apsd 0" command can still be used to
disable this if needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant_create_ap() is only called for AP mode, so there is no
point in trying to address station (infra/IBSS) modes.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"NFC_REPORT_HANDOVER {INIT,RESP} P2P <req> <sel>" can now be used to
report completed NFC negotiated connection handover in which the P2P
alternative carrier was selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New functionality is needed for this with the update NFC connection
handover design that depends on the AP side using the public key hash
from the handover request.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When GAS is used with PMF negotiated, Protected Dual of Public Action
frames are expected to be used instead of Public Action frames, i.e.,
the GAS/ANQP frames are expected to be encrypted. Add support for this
different category of Action frames being used for GAS. The payload
after the Category field is identical, so the only change is in using
the Category field based on what was received in the request frames. For
backwards compatibility, do not enforce protected dual to be used on the
AP side, i.e., follow what the station does.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A TX status event could be received after the AP interface has already
been deinitialized. This needs to check for NULL pointer before trying
to indicate the event to AP functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPA_CIPHER_* and CIPHER_* are used for the exact same set of cipher
suites with the main difference being that the WPA_CIPHER_* version is
suitable to be used as a bitfield. Similarly, WPA_KEY_MGMT_* and
KEY_MGMT_* have similar design for AKMs. There is no need to maintain
two separate copies of the definitions since the bitfield compatible
version can be used for both needs. Get rid of the CIPHER_* and
KEY_MGMT_* versions to clean up the implementation by getting rid of
unnecessary mapping functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds initial parts for supporting the new GCMP-256, CCMP-256,
BIP-GMAC-128, BIP-GMAC-256, and BIP-CMAC-256 cipher suites.
Signed-hostap: Jouni Malinen <j@w1.fi>
Adds support for VHT by parsing bandwidth and center_freq{1,2}.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add chan_switch to the control interface of wpa_supplicant and hostapd,
and also to wpa_cli and hostapd_cli.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Build CSA settings and call the driver to perform the switch. Construct
Beacon, Probe Response, and (Re)Association Response frames both for CSA
period and for the new channel. These frames are built based on the
current configuration. Add CSA IE in Beacon and Probe Response frames.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This makes it more convenient to move BSS configuration entries between
struct hostapd_config instances to clean up per-BSS configuration file
design.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit ca9bc5b566 added wpas_conf_ap_vht()
as a static function with the caller within CONFIG_IEEE80211N, but the
function outside. This resulted in a compiler warning for wpa_supplicant
AP/P2P builds when CONFIG_IEEE80211N=y was not used. Fix that by using
matching conditional block around the function.
Signed-hostap: Jouni Malinen <j@w1.fi>
Start GO with VHT support if VHT option was requested
and the appropriate channels are available.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
wpa_supplicant crashes if driver configuration for AP mode interface
configuration fails after group negotiation. This is because of a
regression from commit 1075b29571 that
ends up freeing the wpa_s instance from within
wpa_supplicant_create_ap() without the caller knowing.
Fix this by using an eloop timeout to free remove the P2P group so that
wpa_supplicant_create_ap() and especially wpa_supplicant_associate()
callers do not need to know about interface getting possibly removed. In
addition, move the P2P specific code into p2p_supplicant.c where it
really belongs. This allows the already existing group formation timeout
to be used by reducing the timeout to zero.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
"wpa_cli p2p_set per_sta_psk <0/1>" can now be used to disable/enable
use of per-device PSKs in P2P groups. This is disabled by default.
When enabled, a default passphrase is still generated by the GO for
legacy stations, but all P2P and non-P2P devices using WPS will get
a unique PSK.
This gives more protection for the P2P group by preventing clients from
being able to derive the unicast keys used by other clients. This is
also a step towards allowing specific clients to be removed from a group
reliably without having to tear down the full group to do so.
Signed-hostap: Jouni Malinen <j@w1.fi>
There were some code paths that allowed obsolete configuration data
pointer to be maintained within EAPOL supplicant in case a network was
removed while not connection to it (i.e., wpa_s->current_ssid not
pointing to the network that was removed). This could result in use of
freed memory, e.g., from eap_sm_notify_ctrl_attached() when a new
control interface connected prior to the EAPOL supplicant configuration
pointer got updated.
Signed-hostap: Jouni Malinen <j@w1.fi>
In AP mode the frequency was initialized only after trying to set up the
AP which caused failure. Move AP frequency initialization to the right
place. This allows an AP mode network block without the frequency
parameter to be used with the default channel 11 being selected in that
case.
Signed-hostap: Avraham Stern <avraham.stern@intel.com>
There is no need to wait for the 15 second group formation timeout
before indicating P2P group formation failure if GO mode cannot be
started successfully for some reason.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
11b rates removal have had impact on SoftAP functionality in
wpa_supplicant. This patch verifies that only in case of P2P group
operation 11b rates will be eliminated. Refer also to commit
4c2c302893.
Signed-hostap: Alexander Bondar <alexander.bondar@intel.com>
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Some extended capabilities (I'm currently interested in "Operating Mode
Notification" for VHT) are implemented by the kernel driver and exported
in nl80211. Use these in hostapd/wpa_supplicant.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This new parameter allows wpa_supplicant AP mode operations to use
similar design to the vendor_elements parameter in hostapd to add
vendor_elements into Beacon/Probe Response IE parameters.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
beacon_int (in TU) can now be used to configure Beacon interval for AP
mode operations (including P2P GO) in wpa_supplicant. This can be set
either in a network block or as a global parameter in the configuration
file (or with "SET beacon_int <value>" control interface command) to
apply for all networks that do not include the beacon_int parameter to
override the default.
In addition, this commits extends the dtim_period parameter to be
available as a global parameter to set the default value. dtim_period is
now stored in the configuration file, too, if it was set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit bbf41865c9 added calls to functions
that are only defined if CONFIG_WPS_NFC=y. Protect those calls properly
to avoid build issues.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_supplicant is controlling an AP mode interface, it can generate
the alternative carrier record for NFC connection handover select
message similarly to the way this is done in hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_supplicant is controlling an AP mode interface, it can generate
the NFC configuration token similarly to the way this is done in
hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This was used to select between "(auth)" and "(reauth)" in
CTRL-EVENT-CONNECTED events. However, the variable was not cleared
anywhere else apart from the AP deinit case. As such, it did not really
provide correct information and is not really of much use even with
proper clearing added. As such, it is cleaner to just get rid of this
altogether.
Signed-hostap: Jouni Malinen <j@w1.fi>
Basic support for the 60 GHz band. Neither P2P nor WPS are yet taken
care off. Allows to start AP with very simple config:
network={
ssid="test"
mode=2
frequency=60480
key_mgmt=NONE
}
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The PSK generation done by pbkdf2_sha1() is one of the longest CPU time
users according to our profiling from boot to GO started.
So I have reduced some steps.
I could boot a GO by this command sequence.
-------------
add_net
set_network 0 ssid '"DIRECT-XX"'
set_network 0 psk
'"123456789012345678901234567890123456789012345678901234567890123"'
set_network 0 proto RSN
set_network 0 key_mgmt WPA-PSK
set_network 0 pairwise CCMP
set_network 0 auth_alg OPEN
set_network 0 mode 3
set_network 0 disabled 2
p2p_group_add persistent=0 freq=2412
-------------
By this sequence, pbkdf2_sha1() was called three times and the function
calculates the same value each time. Reduce number of calls to
pbkdf2_sha1() from 3 to 1 by caching the previous result.
Signed-hostap: Masashi Honma <masashi.honma at gmail.com>
Extend the wpa_cli wps_pin command to support specification of the PIN
expiration time in seconds similarly to hostapd_cli wps_pin command when
using wpa_supplicant for AP mode (including P2P GO).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add optional "ht40" argument for p2p_group_add command to enable 40 MHz
in 5GHz band. This configures the secondary channel, when HT support is
enabled and if the HW supports 40 MHz channel width.
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
In case of P2P GO and AP mode, wpa_supplicant uses the default hostapd
parameters for WMM. In the default parameters the ACM bit for video and
voice are set to 1, meaning, P2P devices and stations which are
connected to the GO cannot pass voice or video data packets. Allow this
to be changed through wpa_supplicant configuration file with wmm_ac_*
parameters.
Signed-hostap: Yoni Divinsky <yoni.divinsky@ti.com>
Some drivers may independently decide to switch channels. Handle this by
updating the hostapd and wpa_supplicant AP and GO configuration.
Signed-hostap: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
This can be used with P2P management operations that need to verify
whether the local device is operating a specific group based on
P2P Group ID attribute from a peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This workaround for Windows 7 WPS probing mechanism was previously
allowed only with hostapd, but the same interoperability issue can
happen with wpa_supplicant AP/GO mode. Allow the workaround to be
enabled in wpa_supplicant configuration for these uses.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.
Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.
My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Implement wps_cancel for hostapd similarly to how it was already
supported in wpa_supplicant AP mode.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This patch adds a configuration in network block, ap_max_inactivity, for
station's inactivity period when in AP mode. The time period is
configured in seconds, by default 300 seconds.
Signed-hostap: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
This also disables WPS support if hidden SSID is enabled in AP mode.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Move disassociate and deauthenticate commands to ctrl_iface_ap.c, so
that they ares accessible for wpa_supplicant AP mode and wpa_cli (with
CONFIG_AP option enabled).
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Add a new persistent group network block field, p2p_client_list, to
maintain a list of P2P Clients that have connected to a persistent
group. This allows GO of a persistent group to figure out more easily
whether re-invocation of a persistent group can be used with a specific
peer device.
Signed-hostap: Jouni Malinen <j@w1.fi>
The active station connection triggered wpa_supplicant AP mode startup
to try to update Beacon IEs before the AP mode was properly initialized
and that resulted in NULL pointer dereference in driver_nl80211.c. Fix
this by skipping the IE update before the AP mode is initialized.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When using wpa_supplicant AP mode, WPS support is enabled by default for
WPA/WPA2-Personal. Change this to enforce the WPS2 rules on not allowing
WPS to be used with WPA/TKIP-only configuration (i.e., at minimum, mixed
mode with WPA/TKIP and WPA2/CCMP has to be used for WPS to be enabled).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Set the HT capabilities of a P2P GO according to the wiphy supported
ones. Mask-in a white-list of HT capabilities that won't cause problems
for non-supporting stations.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Send the connection events from P2P group to both the group interface
and parent interface ctrl_ifaces to make it easier for external monitor
programs to see these events without having to listen to all group
interfaces when virtual group interfaces are used.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The new event can be used when EAPOL TX status can't be reported as a
complete 802.11 frame but is instead reported as just the EAPOL data as
originally passed to hapd_send_eapol().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
In AP mode, authentication algorithm is reset in
hostapd_config_defaults_bss() and never set to the configured one. This
would pass the default auth_algs (OPEN|SHARED) to driver regardless of
what the wpa_supplicant configuration is requesting.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
When wpa_supplicant AP mode is used, WPS was enabled by default
regardless of security mode. This is not desired for WEP, so change
the AP configuration to enable WPS only for open and WPA/WPA2-Personal
networks.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The hardware feature data is required in several different places
throughout the code. Previously, the data was acquired and freed on
demand, but with this patch wpa_supplicant will keep a single copy
around at runtime for everyone to use.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
This offloads the station polling to driver wrappers, which may offload
it again to the driver. The hostap driver wrapper uses "real" data
frames while nl80211 uses null data frames.
Also add a specific event to indicate that a poll was successful for
future use with the nl80211 driver.
The previous code was trying to figure out which WPA version is
used based on the extra IEs requested for Association Request. That
did not work properly in cases where non-WPA networks are used with
some extra IEs. Fix this by using more robust mechanism for passing
the WPA versions from core wpa_supplicant to the driver_ops
associate().
If uapsd is explicitly enabled, set conf->bss->wmm_enabled and
conf->bss->wmm_uapsd to enable (and advertise) uapsd.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Only accept Probe Request frames that have a Wildcard BSSID and a
destination address that matches with our P2P Device Address or is the
broadcast address per P2P specification 3.1.2.1.1.
The current implementation of p2p_intra_bss doesn't work since the flag
isn't propagated into the corresponding hostapd config, so AP code will
never enable AP isolation and will in fact disable it again after it had
been enabled by the P2P code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver supports HT20, set the config parameter ieee80211n
to enable it. This does not enable HT40.
Signed-off-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
Regardless of how the AP mode is disabled, wpa_supplicant_ap_deinit()
must be called. Make sure this happens on all paths by calling the
deinit function from wpa_supplicant_mark_disassoc().
Fix a NULL pointer dereference in commit
3734552f15 in the case of PBC overlap and
timeout case.
Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
Signed-off-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
Signal is triggered if an error occurs during WPS provisioning phase.
Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
Commit c76e5d7f9b moved the
ap_configured_cb() call into a completion callback from AP mode code.
However, this callback can be called before hostap_setup_interface()
returns. In that case, the ap_configured_cb() ended up getting
called before the wpa_supplicant connection information was updated.
Fix this by reordering code to set up everything before calling
hostapd_setup_interface().
The AP code might, currently only in the case of HT40, defer actual
enabling to after a scan. In this case, the wpa_s AP code gets confused.
Add a callback for it to use and make it use it to finish only when the
setup has actually completed.
With appropriate hacks in place this allows using HT40 in P2P mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of converting back and forth from the string representation,
always use the binary representation internally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the wpa_supplicant configuration file does not specify an UUID,
we need to copy the generated UUID, not the all zeros buffer
reserved for the configured UUID.
An optional parameter, p2p_dev_addr, can now be given to WPS_PBC
command on P2P GO to indicate that only the P2P device with the
specified P2P Device Address is allowed to connect using PBC. If
any other device tries to use PBC, a session overlap is indicated
and the negotiation is rejected with M2D. The command format for
specifying the address is "WPS_PBC p2p_dev_addr=<address>", e.g.,
WPS_PBC p2p_dev_addr=02:03:04:05:06:07
In addition, show the PBC session overlap indication as a WPS failure
event on an AP/GO interface. This particular new case shows up as
"WPS-FAIL msg=4 config_error=12".
The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
assoc_freq needs to be cleared when an interface gets disconnected.
This fixes an issue where P2P Action frame transmission may fail
because of missing remain-on-channel operation when using the same
interface for group operations (or non-P2P connections) and P2P
management operations.
The duplicated WPS event in the parent interface should only be used
during P2P group formation, i.e., when the WPS operation was actually
started using the parent interface. When authorizing a client to
connect to an already running group, the WPS command is issued on
the group interface and there is no need to duplicate the event to
the parent interface.
