If unicast Authentication Request frame is used and the peer ACKs such a
frame, but does not reply within the two second limit, there is no need
to continue trying to retransmit the request frames since the peer was
found, but not responsive.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new conf={sta,ap}-{sae,psk-sae} parameter values can now be used to
specify that the legacy configuration object is for SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows DPP to be used for enrolling credentials for SAE networks in
addition to the legacy PSK (WPA-PSK) case. In addition, enable FT-PSK
and FT-SAE cases automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Retransmit the PKEX Exchange Request frame if no response from a peer is
received. This makes the exchange more robust since this frame is sent
to a broadcast address and has no link layer retries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to allow more invalid attribute values to be written
into Peer Discovery Request/Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to cover a case where Config Attrib Object value is
invalid in Configuration Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant DPP implementation to retransmit DPP
Authentication Response frame every 10 seconds up to 5 times if the peer
does not reply with DPP Authentication Confirm frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this command stopped listen operation immediately, but if
there was an ongoing authentication exchange, a new listen operation was
started. This is not really expected behavior, so stop the
authentication exchange first with this command to avoid restarting
listen operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new role=either parameter can now be used with DPP_AUTH_INIT to
indicate that the initiator can take either the Configurator or Enrollee
role.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Generate the PKEX bootstrapping information and release the PKEX session
in a helper function that both the initiator and responder can use
instead of maintaining this functionality separately in two places.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces the ACS functionality for the autonomous GO. The
optional parameter <freq> in p2p_group_add is enhanced to carry a value
"acs" with the intention to select the channels among any supported
band. freq = 2 / 5 carry the need to select the channels only in the
respective bands 2.4 / 5 GHz. This functionality is on top of the host
driver's capability to offload ACS, which is advertized through
WPA_DRIVER_FLAGS_ACS_OFFLOAD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add limit on number of failed attempts that could have used PKEX code.
If the limit (5) is reached, drop the PKEX state (including the code)
and report this on the control interface to indicate that a new code
needs to be entered due to possible attack.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clean up the pending PKEX exchange if Commit-Reveal Request processing
indicates a mismatch in the PKEX code. Previously, the this case was
silently ignored and the session was left in pending state that
prevented new PKEX exchanges from getting initated. Now, a new attempt
is allowed to be initiated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Report mismatching finite cyclic group with PKEX Exchange Response using
STATUS_BAD_GROUP and provide more detailed error report over the control
interface on the peer device when this happens.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Indicate to upper layers if PKEX Commit-Reveal Request frame AES-SIV
decryption fails. That is a likely sign of the PKEX code mismatch
between the devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP AKM should really require PMF to be used, but since that is not yet
explicitly required in the specification, make PMF enabled for now. For
legacy PSK cases, configure PMF to be enabled as well to support both
APs in no-PMF, optional-PMF, and required-PMF configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow the Initiator to request a different channel to be used for DPP
Authentication and DPP Configuration exchanges. This commit adds support
for this in wpa_supplicant with the optional neg_freq=<freq in MHz>
parameter in DPP_AUTH_INIT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wpa_supplicant dpp_config_obj_override,
dpp_discovery_override, and dpp_groups_override parameters to be cleared
by setting them to a zero-length value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Both the DPP-TX and DPP-TX-STATUS events are provided.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that dpp_check_attrs() takes care of verifying that no attributes
are after the Wrapped Data attribute, the duplicated checks in hostapd
and wpa_supplicant side of the implementation can be removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a generic mechanism for configuring the DPP implementation to behave
in particular different (mostly incorrect) ways for protocol testing
purposes. The new dpp_test parameter can be set to a non-zero integer to
indicate a specific behavior. This is only available in
CONFIG_TESTING_OPTIONS=y builds.
This commit include cases for an extra attribute being added after the
Wrapped Data attribute and Initiator/Responder capabilities having an
unexpected zero capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Seems like some test cases, e.g., ap_wpa2_psk_ext_retry_msg_3c, require
larger buffer than 256 bytes.
In other case I fail such test cases when run on real HW and using:
CONFIG_CTRL_IFACE=udp-remote
Increase the RX buffer from 256 to 4096 bytes to match the other control
interface cases.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
After an initial connection wpa_supplicant derives ERP information which
can be used in doing eventual authentications in the same realm. This
information can be used by drivers with offloaded FILS support to do
driver/firmware initiated roamings. Add support to send this updated
information to such drivers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to be able to use the same implementation for updating
the connection parameters in the driver during an association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the replay counter after a roam for all cases. This restores the
design back to what it was before commit
01ef320f19 ('FILS: Update ERP next
sequence number with driver offload').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant RESEND_ASSOC command can be used to request the
last (Re)Association Request frame to be sent to the AP to test FT
protocol behavior.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new wpa_supplicant "KEY_REQUEST <error=0/1> <pairwise=0/1>" command
can be used to request an EAPOL-Key Request frame to be sent to the AP.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 03ed0a5239 ('WNM: Ignore WNM-Sleep
Mode Response if WNM-Sleep Mode has not been used') started ignoring the
response when no WNM-Sleep Mode Request had been used during the
association. This can be made tighter by clearing the used flag when
successfully processing a response. This adds an additional layer of
protection against unexpected retransmissions of the response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new sae_password network profile parameter can now be used to set
the SAE password instead of the previously used psk parameter. This
allows shorter than 8 characters and longer than 63 characters long
passwords to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While considering the movement of P2P GO from its current operating
channel, do not mark a DFS channel as invalid if DFS is offloaded
to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wpas_p2p_select_go_freq_no_pref() ended up selecting a 2.4
GHz band channel first before even considering 5 or 60 GHz channels.
This was likely done more or less by accident rather than by design when
the 5 GHz and 60 GHz band extensions were added. It seems reasonable to
enhance this by reordering the code to start with 5 and 60 GHz operating
classes and move to 2.4 GHz band only if no channel was available in 5
or 60 GHz bands for P2P GO use.
This does have some potential interop issues with 2.4 GHz only peer
devices when starting up an autonomous GO (i.e., without there being
prior knowledge of channels that the peers support). Upper layers are
expected to enforce 2.4 GHz selection if that is needed for some use
cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows CONFIG_TESTING_OPTIONS=y builds of wpa_supplicant to
override the OWE DH Parameters element in (Re)Association Request frames
with arbitrary data specified with the "VENDOR_ELEM_ADD 13 <IE>"
command. This is only for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This additional field was added to DPP Public Action frames in DPP tech
spec v0.2.3 to support cryptographic agility in the future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only the SME-in-wpa_supplicant case was supported. This
extends that to cover the drivers that implement SME internally (e.g.,
through the cfg80211 Connect command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in wpa_supplicant to allow DH groups 20 and 21
to be used in addition to the mandatory group 19 (NIST P-256). The group
is configured using the new network profile parameter owe_group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in hostapd to allow DH groups 20 and 21 to be
used in addition to the mandatory group 19 (NIST P-256).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for using the OWE Transition Mode element to determine the
hidden SSID for an OWE BSS that is used in transition mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
