Beacon frames are not supported in IEEE 802.11ad network (DMG-beacons
used instead). To allow hostapd to manage IEEE 802.11ad AP with
device_ap_sme disabled, skip nl80211_register_beacons() for IEEE
802.11ad AP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
This allows kernel to force disconnection if something kills the
wpa_supplicant process in a manner that does not allow proper cleanup to
be performed. The association is not supposed to be allowed to continue
after process has ended since there are number of operations that
wpa_supplicant may need to do during the association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Authentication and Deauthentication frames are not used in DMG/IEEE
802.11ad networks. For DMG/IEEE 802.11ad the following was implemented:
Upon receiving association request, allocate the sta object and
initialize it as if authentication took place. Upon receiving
disassociation, deallocate the sta object.
ap_sta_disassociate/ap_sta_deauthenticate/ap_sta_disconnect all use
disassociation instead of deauthentication. In driver_nl80211,
i802_sta_deauth() is routed to i802_sta_disassoc().
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
On a connect nl80211 event, wpa_supplicant uses
wpa_driver_nl80211_get_ssid() to fetch the current associated SSID to
compare to existing configurations. However,
wpa_driver_nl80211_get_ssid() uses drv->ssid, which is a cached value.
It is set when we explicitly initial a connect request using
wpa_supplicant. If the association was initiated outside of
wpa_supplicant, we need another way to populate drv->ssid. This commit
sets drv->ssid based on cfg80211 BSS information on connect/associate
nl80211 events.
Signed-off-by: Ningyuan Wang <nywang@google.com>
This adds support for nl80211 NL80211_CMD_SET_MULTICAST_TO_UNICAST
command.
By setting the new hostapd configuration option multicast_to_unicast=1,
hostapd configures this AP to perform multicast to unicast conversion.
When enabled, all multicast packets with ethertype ARP, IPv4, or IPv6
(possibly within an 802.1Q header) will be sent out to each station once
with the destination (multicast) MAC address replaced by the station's
MAC address. Note that this may break certain expectations of the
receiver, e.g., the ability to drop unicast IP packets encapsulated in
multicast L2 frames, or the ability to not send destination unreachable
messages in such cases.
This also does not implement Directed Multicast Service (DMS).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Do not use the generic bss_info_handler() design to fetch all scan
results into temporary memory buffer. Instead, use a separate BSS info
handler that fetches the requested information without fully parsing the
BSS entries and without allocating any memory for collecting all the
results.
This is also simplifying bss_info_handler() and nl80211_parse_bss_info()
design by getting rid of the special case that was used only for
nl80211_get_assoc_freq() and not normal scan result fetching.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the driver advertises support for setting Beacon frame data rate,
allow the user to configure this rate as part of starting the AP. Only
one Beacon frame TX rate is allowed.
Drivers advertising such support should set corresponding flag via the
NL80211_ATTR_EXT_FEATURES attribute.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit fixes the nl80211 driver call get_inact_sec() to return -1
when STA inactivity time retrieval fails in i802_read_sta_data().
This was intended to be handled by initalizing the inactive_msec member
to -1 but i802_read_sta_data() assumes the data parameter is
uninitialized and memsets the entire structure, neutralizing the attempt
to distinguish between no value (-1) and a time value of 0.
This is fixed by now requiring i802_read_sta_data() callers to
initialize the data structure first (allowing get_inact_sec() to use
-1). This is a safe change because it does not change any driver API
behavior and only affects one other static function in driver_nl80211.c
Signed-off-by: Joel Cunningham <joel.cunningham@me.com>
This commit adds a control interface command to configure the TDLS
trigger mode to the host driver. This TDLS mode is configured through
the "SET tdls_trigger_control" control interface command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This sends the FILS KEK and AAD context (nonces) to the driver with the
NL80211_CMD_ASSOCIATE messages when using FILS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it cleaner for the FILS implementation to use the same design
for setting Authentication frame elements as was already done with SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to find bss->drv separately for each parameter, so do
this once at the beginning of the function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add driver parameter command to force capability flag
WPA_DRIVER_FLAGS_BSS_SELECTION even if driver states otherwise. This is
mainly for testing purposes.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
This reverts commit 647862eb60.
The second check of device_ap_sme looks like duplicated, but it isn't
actually. The trick is nl80211_create_monitor_interface may change that
variable value and the second evaluation may give a different result.
This definitely isn't a very clear code, but that change caused a
regression for drivers that:
1) Don't report NL80211_ATTR_DEVICE_AP_SME
2) Don't support monitor mode
3) Don't support subscribing for PROBE_REQ and/or ACTION frames
like brcmfmac. With such drivers hostapd doesn't start anymore.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Accoding to the comment of struct wpa_driver_mesh_bss_params, the
max_peer_links parameter should be under that struct.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Previously, driver_nl80211 sets NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT in
AP mode, to get EAPOL frames out unencrypted when using IEEE 802.1X/WEP.
However, due to the way nl80211/cfg80211 is implemented, this attribute
is ignored by the kernel if NL80211_ATTR_CONTROL_PORT_ETHERTYPE isn't
specified as well. Fix this by including
NL80211_ATTR_CONTROL_PORT_ETHERTYPE set to ETH_P_PAE. This can be done
unconditionally, since the kernel will allow ETH_P_PAE to be set even
when the driver didn't advertise support for arbitrary ethertypes.
Additionally, the params->pairwise_ciphers appear to not be set at
this point, so relax the check and allow them to be zero.
In client mode, this whole thing was missing, so add it. Again, the
pairwise suite can be WPA_CIPHER_NONE, so allow that case as well.
This fixed IEEE 802.1X/WEP EAP reauthentication and rekeying to use
unencrypted EAPOL frames which is the de facto way of implementing this
in wireless networks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes wpa_supplicant set default scan IEs to the driver (if the
vendor command is supported). The driver can use these IEs in the scan
requests initiated by the driver itself. Also the driver can merge these
IEs into further scan requests that it receives, in case if the scan
request doesn't carry any of the IEs sent in this command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If params->freq is NULL here, it leads to a segfault. Do not initialize
bss->bandwidth if params->freq is NULL.
Signed-off-by: Chaitanya T K <Chaitanya.Mgit@gmail.com>
Previously, HT capability IE and HT information IE were included in
Beacon and Mesh Peering Open/Confirm frames even if HT is disabled with
disable_ht=1. This patch removes these.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
reports mesh peer AID to kernel.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This allows P2P Listen to be offloaded to device to enhance power
saving.
To start P2P listen offload, from wpa_cli interface, issue the command:
p2p_lo_start <freq> <period> <interval> <count>
To stop P2P listen offload, issue the command:
p2p_lo_stop
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
During the P802.11s draft development, there were separate LISTEN and
IDLE states. However, the current IEEE 802.11 standards uses only the
IDLE state while the implementation called this LISTEN. Rename the state
in the implementation to match the one used in the standard to avoid
confusion. In addition, rename OPEN_{SENT,RCVD} to OPN_{SNT,RCVD} to
match the exact spelling of these states in the standard.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set max peer links to kernel even when wpa_supplicant MPM is used. This
sets the correct value for the "Accepting Additional Mesh Peerings bit"
in "Mesh Capability field" in "Mesh Configuration element" in the Beacon
frame.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes changes such that hostapd (and wpa_supplicant AP mode)
registers to kernel for specific Action frames instead of generically
registering for all Action frames. This makes it easier for other
programs to register for some Action frames that hostapd does not handle
today without having to somehow coordinate directly with hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
One of supported code paths already allows this scenario. It is used if
driver doesn't report NL80211_ATTR_DEVICE_AP_SME and doesn't support
monitor interface. In such situation:
1) We don't quit if subscribing for WLAN_FC_STYPE_PROBE_REQ fails
2) We don't try subscribing for WLAN_FC_STYPE_ACTION
3) We fallback to AP SME mode after failing to create monitor interface
4) We don't quit if subscribing for WLAN_FC_STYPE_PROBE_REQ fails
Above scenario is used, e.g., with brcmfmac. As you can see - thanks to
events provided by cfg80211 - it's not really required to receive Probe
Request or action frames.
However, the previous implementation did not allow using hostapd with
drivers that:
1) Report NL80211_ATTR_DEVICE_AP_SME
2) Don't support subscribing for PROBE_REQ and/or ACTION frames
In case of using such a driver hostapd will cancel setup after failing
to subscribe for WLAN_FC_STYPE_ACTION. I noticed it after setting flag
WIPHY_FLAG_HAVE_AP_SME in brcmfmac driver for my experiments.
This patch allows working with such drivers with just a small warning
printed as debug message.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
The os_snprintf() call here cannot really fail in practice, but since
its result was stored into the local variable and not checked, static
analyzers could warn about the unused assignment. Clean this up by
checking the return value.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set the global RRM flag if global RRM is supported by the device. Also,
allow RRM in (Re)Association Request frame if the global RRM flag is
set.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Register to receive Radio Measurement Request frames since LCI request
is supported by wpa_supplicant.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Implement configure_data_frame_filters() callback by using
the net-sysfs interfaces (if these are available).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If a legacy client with no P2P PS support is trying to connect to
a P2P GO, the driver should know that, and change its PS behavior
accordingly.
Add a parameter to hostapd_sta_add_params() indicating if P2P PS is
supported by the station and pass this parameter to kernel with nl80211
driver when the station is added/set.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
cfg80211 reports a deauth/disassoc event when internally clearing
connection with the previous BSS. Ignore that event to allow the new
connect command to complete.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier for drivers that use the Connect command instead of
separate Auth+Assoc commands to determine when to use reassociation
instead of association. Matching changes are still needed in cfg80211 to
allow this parameter to be used, but it is safe for wpa_supplicant to
start including this attribute now since it will be ignored by older
cfg80211 versions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Interface additions/removals are not guaranteed to be for the driver
listening to the kernel events. As such, send the events to
wpa_supplicant_event_global() which can then pick the correct interface
registered with wpa_supplicant to send the event to.
Signed-off-by: Roy Marples <roy@marples.name>
Commit 732b1d20ec ('nl80211: Clean up
ifidx properly if interface in a bridge is removed') added
drv->if_indices_reason array similarly to the previously used
drv->if_indices. However, it had a copy-paste error here on the error
path where a reallocation failure after at least one successful
reallocation would result in the drv->if_indices being overridden
instead of restoring drv->if_indices_reason to the old value. Fix this
by setting the correct variable on the error path. (CID 138514)
Signed-off-by: Jouni Malinen <j@w1.fi>