Add more hang reason codes for the hang reason in the
QCA_NL80211_VENDOR_SUBCMD_HANG events. This also introduces the
attribute QCA_WLAN_VENDOR_ATTR_HANG_REASON_DATA to carry the required
data for the respective hang reason. This data is expected to contain
the required dump to analyze the reason for the hang.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Some APs have managed to add two SSID elements into Beacon frames and
that used to result in picking the last one which had incorrect data in
the known examples of this misbehavior. Pick the first one to get the
correct SSID.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_parse_kde_ies(), i.e., the only caller to wpa_parse_generic(),
verifies that there is room for KDE Length field and pos[1] (that
length) octets of payload in the Key Data buffer. The PMKID KDE case
within wpa_parse_generic() was doing an unnecessary separate check for
there being room for the Length, OUI, and Data Type fields. This is
covered by the check in the calling function with the combination of
verifying that pos[1] is large enough to contain RSN_SELECTOR_LEN +
PMKID_LEN octets of payload.
This is confusing since no other KDE case was checking remaining full
buffer room within wpa_parse_generic(). Clean this up by removing the
unnecessary check from the PMKID KDE case so that all KDEs are handled
consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_parse_generic() can now recognize the Key ID KDE that will be needed
to deliver the Key ID of the pairwise key when Extended Key ID is used.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
KEY_FLAG_MODIFY was initial added for the planned Extended Key ID
support with commit a919a26035 ("Introduce and add key_flag") and then
removed with commit 82eaa3e688 ("Remove the not yet needed
KEY_FLAG_MODIFY") to simplify commit e9e69221c1 ("Validity checking
function for key_flag API").
Add it again and update check_key_flag() accordingly.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Check whether an error is reported from any of the functions that could
in theory fail and if so, do not proceed with the partially filled SAE
commit buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
There was a copy-paste error in this code that would be adding the
connectorTemplate once that becomes available. In practice, this was not
reachable code, but anyway, this should be ready for potential addition
of connectorTemplate in the future.
Signed-off-by: Jouni Malinen <j@w1.fi>
The initial implementation of the PTK derivation workaround for
interoperability with older OWE implementations forced
WPA_KEY_MGMT_PSK_SHA256 to be used for all of PTK derivation. While that
is needed for selecting which hash algorithm to use, this was also
changing the length of the PTK components and by doing so, did not
actually address the backwards compatibility issue.
Fix this by forcing SHA256 as the hash algorithm in PTK derivation
without changing the PTK length calculation for OWE when
owe_ptk_workaround is enabled.
Fixes: 65a44e849a ("OWE: PTK derivation workaround in AP mode")
Fixes: 8b138d2826 ("OWE: PTK derivation workaround in STA mode")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add masks for each key type to define which flags can be combined and
add a helper function to validate key_flag values.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
I decided to drop KEY_FLAG_MODIFY instead of allowing flag combinations not
yet used in the code and will simply recreate it with the Extended Key
ID patches once we get there. For that reason I also did not renumber
the flags.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The commit a34ca59e (SAE: Allow SAE password to be configured separately
(STA)) added sae_password configuration option. We should also consider
sae_password in the wpa_config_write() function which stores the valid
network block details to an external database.
Fixes: a34ca59e4d ("SAE: Allow SAE password to be configured separately (STA)")
Signed-off-by: Sachin Shelke <sachin.shelke@nxp.com>
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Add support for element defragmentation as defined in IEEE
P802.11-REVmd/D3.0, 10.28.12 (Element defragmentation).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
IEEE P802.11az/D2.0 renamed the FILS Wrapped Data element,
removing the FILS prefix. Change the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_ctrl.h can be installed separately with libwpa_client, so
utils/common.h won't be available to its users.
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Add an attribute QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME for specifying
dwell time in the QCA vendor scan command. This is a common value which
applies across all frequencies requested in the scan.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This attribute enables/disables the host driver to send roam reason
information in the Reassociation Request frame to the AP in the same
ESS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Couple of the attributes were defined with inconsistent prefix in the
name (missing "CONFIG_"). Fix these to use the common prefix for all
enum qca_wlan_vendor_attr_config values. Add defined values for the
incorrect names to avoid issues with existing users.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Rekeying a pairwise key using only keyid 0 (PTK0 rekey) has many broken
implementations and should be avoided when using or interacting with
one. The effects can be triggered by either end of the connection and
range from hardly noticeable disconnects over long connection freezes up
to leaking clear text MPDUs.
To allow affected users to mitigate the issues, add a new hostapd
configuration option "wpa_deny_ptk0_rekey" to replace all PTK0 rekeys
with disconnection. This requires the station to reassociate to get
connected again and as such, can result in connectivity issues as well.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The HE Operation field for BSS color consists of a disabled, a partial,
and 6 color bits. The original commit adding support for BSS color
considered this to be a u8. This commit changes this to the actual
bits/values.
This adds an explicit config parameter for the partial bit. The disabled
is set to 0 implicitly if a bss_color is defined.
Interoperability testing showed that stations will require a BSS color
to be set even if the feature is disabled. Hence the default color is 1
when none is defined inside the config file.
Signed-off-by: John Crispin <john@phrozen.org>
This commit adds new attributes for getting the Probe Response frame
IEs, Beacon frame IEs and the disconnection reason codes through
get_sta_info vendor command.
The host driver shall give this driver specific reason code through
the disconnection reason code attribute
QCA_WLAN_VENDOR_ATTR_GET_STA_DRIVER_DISCONNECT_REASON.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This acts as an event from the host driver to the user space to notify
the driver specific reason for a disconnection. The host driver
initiates the disconnection for various scenarios (beacon miss, Tx
Failures, gateway unreachability, etc.) and the reason codes from
cfg80211_disconnected() do not carry these driver specific reason codes.
Host drivers should trigger this event immediately prior to triggering
cfg80211_disconnected() to allow the user space to correlate the driver
specific reason code with the disconnect indication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This acts as a vendor event and is used to update the information
of a station from the driver to userspace.
Add an attribute for the driver to update the channels scanned in
the last connect/roam attempt.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This attribute aims to configure the STA to send the Beacon Report
Response with failure reason for the scenarios where the Beacon Report
Request cannot be handled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This ugly hack for being able to search for optional arguments with
space before them was quite inconvenient and unexpected. Clean this up
by handling this mess internally with a memory allocation and string
duplication if needed so that the users of wpa_supplicant control
interface do not need to care about such details.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
As qca_vendor.h alone can be included by other applications, define
macro BIT() in qca_vendor.h itself if not yet defined, e.g., by
including utils/common.h before qca_vendor.h.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This was not supposed to set the constructed bit in the header. Fix this
to avoid parsing issues with other ASN.1 DER parsers.
Fixes: c025c2eb59 ("DPP: DPPEnvelopedData generation for Configurator backup")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make Configurator provisioning require explicit conf parameter enabling
similarly to the previously used conf=ap-* and conf=sta-* cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This avoids unexpected behavior if GAS query fails and the Config
Response does not get processed at all. Previously, this could result in
configuration being assumed to be successful instead of failure when
Config Response object was not received at all. That could result in
undesired Config Result frame transmission with DPP Rel 2 and not
clearing the ongoing DPP session.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, unexpected Authentication Confirm messages were ignored in
cases where no Authentication Confirm message was expected at all, but
if this message was received twice in a state where it was expected, the
duplicated version was also processed. This resulted in unexpected
behavior when authentication result was processed multiple times (e.g.,
two instances of GAS client could have been started).
Fix this by checking auth->waiting_auth_conf before processing
Authetication Confirm. That boolean was already tracked, but it was used
only for other purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Only one peer-commit-scalar value was stored for a specific STA (i.e.,
one per MAC address) and that value got replaced when the next SAE
Authentication exchange was started. This ended up breaking the check
against re-use of peer-commit-scalar from an Accepted instance when
anti-clogging token was requested. The first SAE commit message (the one
without anti-clogging token) ended up overwriting the cached
peer-commit-scalar value while leaving that instance in Accepted state.
The second SAE commit message (with anti-clogging token) added ended up
getting rejected if it used the same value again (and re-use is expected
in this particular case where the value was not used in Accepted
instance).
Fix this by using a separate pointer for storing the peer-commit-scalar
value that was used in an Accepted instance. There is no need to
allocate memory for two values, i.e., it is sufficient to maintain
separate pointers to the value and move the stored value to the special
Accepted state pointer when moving to the Accepted state.
This fixes issues where a peer STA ends up running back-to-back SAE
authentication within couple of seconds, i.e., without hostapd timing
out the STA entry for a case where anti-clogging token is required.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit introduces additional stats to query through
QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds support for generating an encrypted backup of the local
Configurator information for the purpose of enrolling a new
Configurator. This includes all ASN.1 construction and data encryption,
but the configuration and connector template values in
dpp_build_conf_params() are not yet complete.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process the received DPPEnvelopedData when going through Configurator
provisioning as the Enrollee (the new Configurator). This parses the
message, derives the needed keys, and decrypts the Configurator
parameters. This commit stores the received information in
auth->conf_key_pkg, but the actually use of that information to create a
new Configurator instance will be handled in a separate commit.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
There is no need for the Protocol Version attribute in Authentication
Response if the peer is a DPP R1 device since such device would not know
how to use this attribute. To reduce risk for interoperability issues,
add this new attribute only if the peer included it in Authentication
Request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY_FREQUENCY for
primary channel center frequency in the definition for Representative
Tx Power List (RTPL) list entry instance. This is required for 6 GHz
support, since the 6 GHz channel numbers overlap with existing 2.4 GHz
and 5 GHz channel numbers thus requiring frequency values to uniquely
identify channels.
Mark QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY as deprecated if both the
driver and user space application support 6 GHz. For backward
compatibility, QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY is still used if
either the driver or user space application or both do not support the
6 GHz band.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make the selected channel available for upper layer software to use,
e.g., when starting DPP listen operation during NFC negotiated
connection handover.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new control interface commands "DPP_NFC_HANDOVER_REQ own=<id>
uri=<URI>" and "DPP_NFC_HANDOVER_SEL own=<id> uri=<URI>" to support NFC
negotiated connection handover. These commands are used to report a DPP
URI received from a peer NFC Device in Handover Request and Handover
Select messages. The commands return peer bootstrapping information ID
or FAIL on failure. The returned ID is used similarly to any other
bootstrapping information to initiate DPP authentication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
