This was not documented properly and was not really used nor would it be
suitable to be used in generic way as it was implemented. It is better
to just remove the parameter since there does not seem to be any
reasonable use for it.
Static WEP keys were configured only for the first BSS. In addition,
STAs were flushed only for the first BSS. These operations should be in
hostapd_setup_bss(), not setup_interface().
Remove extra call to ieee802_11_set_beacon() for the first BSS. This
should only be done from hostapd_setup_bss(), i.e., once for each BSS.
If every secondary BSS is configured with a pre-set BSSID, hostapd does
not enforce the BSSID mask requirements anymore, i.e., they are used
only if hostapd is responsible for generating MAC addresses for virtual
interfaces.
This is needed to make mac80211 work with multi-BSS configuration. The
previous design ended up setting DTIM period for secondary BSSes before
setting the Beacon and driver_nl80211.c was not really prepared for
that. Eventually, the Beacon configuration routines should be combined
into a single driver operation, but for now, just moving this call is
the simplest workaround.
This updates the terminogy to match with the final WMM specification. In
addition, some of the WMM TSPEC structure fields were in incorrect order
and used without byte order swapping. Those are also taken care of this
cleanup patch.
This cleans up the driver wrapper interface by getting rid of sta_info.h
dependency in all drivers that use MLME implementation in hostapd
(driver_hostap.c and driver_nl80211.c).
driver.h contains the definitions needed in driver wrapper
implementations (driver_*.c) and driver_i.h contains the definitions
that are used in core hostapd code to interact with the driver wrappers.
Previously, only the delivery option 1 from RFC 4284
(EAP-Request/Identity from the AP) was supported. Now option 3
(subsequent EAP-Request/Identity from RADIUS server) can also be used
when hostapd is used as a RADIUS server. The eap_user file will need to
have a Phase 1 user entry pointing to Identity method in order for this
to happen (e.g., "* Identity" in the end of the file). The identity hint
is configured in the same was as for AP/Authenticator case (eap_message
in hostapd.conf).
If a STA reassociates and changes key_mgmt (e.g., from WPA-PSK to WPS),
hostapd needs to reset some of the existing STA and WPA state machine
variables to allow correct processing for the new association.
This depends on a patch to Linux nl80211/mac80211 that has not yet been
merged into wireless-testing. If that change is not present, the old
mechanism (WEXT) will be used instead.
This adds WPS support for both hostapd and wpa_supplicant. Both programs
can be configured to act as WPS Enrollee and Registrar. Both PBC and PIN
methods are supported.
Currently, hostapd has more complete configuration option for WPS
parameters and wpa_supplicant configuration style will likely change in
the future. External Registrars are not yet supported in hostapd or
wpa_supplicant. While wpa_supplicant has initial support for acting as
an Registrar to configure an AP, this is still using number of hardcoded
parameters which will need to be made configurable for proper operation.
This was used to allow hostapd to associate as a non-AP STA to another
AP one the same channel while still acting as an AP with the Host AP
driver. This was very experimental and did not work with all firmware
versions. Nowadays, much better way of doing this is to use mac80211
virtual non-AP STA interface. As such, this experimental code can be
removed from hostapd to reduce the code size and make MLME code easier
to understand since it is now only handling AP functionality.
This code was originally added as a mechanism to handle long waits
during channel selection and/or radar detection. It is not currently
really used and makes the setup sequence nearly impossible to
understand. Let's get rid of the unwanted complexity. This needs to be
redesigned if it is ever needed again.
This code was not finished and did not work with the current mac80211
design. In order to avoid confusing users, it is better to remove this
completely for now and look at new implementation to work with mac80211.
Added a new configuration option, wpa_ptk_rekey, that can be used to
enforce frequent PTK rekeying, e.g., to mitigate some attacks against TKIP
deficiencies. This can be set either by the Authenticator (to initiate
periodic 4-way handshake to rekey PTK) or by the Supplicant (to request
Authenticator to rekey PTK).
With both wpa_ptk_rekey and wpa_group_rekey (in hostapd) set to 600, TKIP
keys will not be used for more than 10 minutes which may make some attacks
against TKIP more difficult to implement.
Changed EAP-FAST configuration to use separate fields for A-ID and
A-ID-Info (eap_fast_a_id_info) to allow A-ID to be set to a fixed
16-octet len binary value for better interoperability with some peer
implementations; eap_fast_a_id is now configured as a hex string.
eap_fast_prov config parameter can now be used to enable/disable different
EAP-FAST provisioning modes:
0 = provisioning disabled
1 = only anonymous provisioning allowed
2 = only authenticated provisioning allowed
3 = both provisioning modes allowed
The configuration data should only store the static configuration data and
not dynamic data. In addition, storing HT configuration and state in IEs is
not the easiest way of doing this, so use more convenient data types for
storing configuration and dynamic state. The HT IEs are then generated
based on the static configuration and dynamic state whenever needed.
