This test case did not clear sched_scan_plans if alloc_fail() resulted
in skipping the test case. This would result in the following
autoscan_exponential and autoscan_periodic test cases failing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
After successfully passing the 525 tests on a remote setup mark the
tests as remote compatible.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The hwsim tests used to execute shell commands in the tests using the
subprocess python module. Use the cmd_execute() general function for
executing "ip addr add/del .." so that this would also work on remote
setups.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
1. Add tests for hostapd neighbor database and neighbor report and
request. Remove the partial neighbor report request test from
test_wpas_ctrl.py since they are now covered more completely in
test_rrm.py.
2. Add LCI request test.
3. Add FTM range request signaling test. This covers only the control
interface commands and measurement request/response exchange for now.
Full end-to-end functionality requires support of station reporting
RRM capability.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Use quotation marks to match the new SSID encoding format in the
NEIGHBOR_REP_REQUEST command. In this specific test case, the exact SSID
value did not make any difference for behavior. The previous version
ended up getting decoded as a hexstring after the NEIGHBOR_REP_REQUEST
format change. The new version goes back to the ASCII string version of
"abcdef".
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (1) converts the cases where apdev[#]['ifname'] was used as
the argument to hostapd.add_ap().
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The OpenSSL memory allocation changes broke this test case. Fix this by
removing the cases that do not get triggered anymore and add a separate
wpas_ctrl_error test case to cover the fail_test() versions of errors.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
init=CORE was previously used due to invalid db.txt data for 00. For
now, allow both it and the new init=USER after fixed db.txt.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for dev[2] to be left with non-default config_methods
parameter at the end of the test case and that could result issues in
following test cases. This hit a failure in the following sequence:
wpas_ctrl_set_wps_params p2ps_channel_active_go_and_station_same
Signed-off-by: Jouni Malinen <j@w1.fi>
mac80211_hwsim only supports 2 different MAC addresses.
Configurations that use a dedicated P2P Device interface already
use these 2 addresses, so adding another interface on the same
PHY results in a duplicated MAC address.
Fix this by changing the MAC address of the added interface to make
sure the new interface has a unique MAC address.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This test case ended up hitting control socket output queue limit
unnecessarily due to the test script not reading pending event messages.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies wpa_supplicant behavior in number of cases where the
external program opening a control interface socket does not behave
properly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for a low powered CPU to take excessively long time to
delete 1000 network blocks when running under valgrind. This would have
resulted in the test case failing and the following reset operation
timing out which would then stop the test sequence completely.
Signed-off-by: Jouni Malinen <j@w1.fi>
run-tests.py is running as root, so sudo does not need to be used
anymore from within each test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
