NL80211_CMD_GET_STATION does not work with the IBSS/mesh BSSID, so clear
the signal strength instead of returning failure when SIGNAL_POLL is
used in an IBSS/mesh.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When an AP interface it created, it is also setup and subscribes
for management frames etc. However, when the interface is added by
wpa_supplicant, setting up for AP operations is redundant because
it will be done by wpa_supplicant on wpa_drv_init() when setting
the interface mode to AP.
In addition, it may cause wpa_supplicant to fail initializing the
interface as it will try to subscribe for management frames on this
interface but the interface is already registered.
Change this, so when adding an AP interface, make setting up the AP
optional, and use it only when the interface is added by hostapd but not
when it is added by wpa_supplicant.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Some drivers (like mac80211) do not accept changing the TX bitrate mask
before the network interface is up. Thus, calling
nl80211_disable_11b_rates() before the interface is up fails, and the
P2P network interface continues to use invalid bitrates.
To fix this call nl80211_disable_11b_rates() immediately after the
interface is brought up (and also after rfkill is unblocked).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Some management frames contain CSA counters which should be updated by
kernel. Change driver op send_mlme() allowing to send a frame,
specifying an array of offsets to the CSA counters which should be
updated. For example, CSA offsets parameters should be specified when
sending Probe Response frames during CSA period.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Channel switch may be performed using both CSA and eCSA IEs together.
This may happen, for example with a P2P GO on band A with legacy
clients. Extend driver API to support up to 2 CSA counters.
This patch also includes the required implementation for nl80211.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This allows the binary sizes to be reduced if no support for nl80211
vendor extensions are needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow wpa_supplicant to use vendor scan (if supported by the driver)
together with the normal nl80211 scan and handling external scan events.
Since this results in possibility of concurrent scan operations, some of
the operations related to scan results need to check more carefully when
an event is relevant for a specific interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows an empty nested list (i.e., no MAC addresses) to be included
in the NL80211_CMD_SET_MAC_ACL message unlike with
nla_nest_start()/nla_nest_end() where the current libnl implementation
removes the "empty" attribute and causes cfg80211 to reject the command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the QCA vendor specific nl80211 interface to query the preferred
frequency list from driver and add a new wpa_cli command to query this
information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Upon GO Negotiation completion, if the remote peer becomes GO, send a
hint event over QCA vendor specific interface to inform the driver of
the likely operating channel of the P2P GO.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the nl80211 interface command "driver status" to retrieve the
concurrency capabilities from the driver using the QCA vendor
extensions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When ACS is offloaded to device driver and the hw_mode parameter is set
to any, the current_mode structure is NULL which fails the ACS command.
Fix this by populating the ACS channel list with channels from all bands
when current_mode is NULL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add vendor command to pass SET setband command to the driver and read
the updated channel list from driver when this notification succeeds.
This allows the driver to update its internal channel lists based on
setband configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, hostapd only supported the case of EAPOL frames receiving
from interfaces enslaved into bridge. This commit adds support for any
Linux master (teaming, openvswitch, bonding, etc.) to be detected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant has stub functions if the external p2p symbols are
unavailable, but the build still fails if the
wpa_driver_nl80211_driver_cmd symbol is missing. Fix this by leaving the
function pointer NULL. This is safe because wpa_drv_driver_cmd() performs
a NULL check.
Signed-off-by: Kevin Cernekee <cernekee@google.com>
Sending a wowlan configuration command can be done on any wireless
interface (not only netdev), as it is a device configuration and not
interface configuration specific. Fix the code to allow it to be
sent on any interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Android libnl_2 implementation added support for "nl80211" name in
commit 'libnl_2: Extend genl_ctrl_resolve() to support "nl80211" name'
in July 2012 which got included in Android 4.2. It is fine to drop this
old Android ICS workaround from wpa_supplicant now.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Change send_mlme() API to allow sending management frames on a specific
channel, overriding the internal driver decision.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When device supports dual band operations with offloaded ACS, hw_mode
can now be set to any band (hw_mode=any) in order to allow ACS to select
the best channel from any band. After a channel is selected, the hw_mode
is updated for hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the WPA_ALG_PMK algorithm in set_key() to result in
trying to configure a key with cipher suite 0. While this results in a
failure from cfg80211 or driver, this is not really desirable operation,
so add a check for cipher suite conversion result before issuing the
nl80211 command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only P2P and mesh use cases enforced unique MAC address for
a dynamically added virtual interface. Extend this to cover normal
station mode interfaces since those can now be added with INTERFACE_ADD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update ACS driver offload feature for VHT configuration. In addition,
this allows the chanlist parameter to be used to specify which channels
are included as options for the offloaded ACS case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The initial IEEE 802.11 ProxyARP functionality in the kernel needed
changes in behavior and that ended up requiring an independent
configuration parameter to be used. Update hostapd to use that new
proxyarp_wifi parameter instead of the earlier proxyarp.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wpa_supplicant to recover from some of the cases where
cfg80211 is unloaded and reloaded without restarting wpa_supplicant. The
netlink socket used for nl80211 events (global->nl_event) seemed to end
up in otherwise functionality state, but with all the event memberships
lost when cfg80211 gets reloaded.
There does not seem to be any clear way of determining when this has
happened, so it looks simplest to just try to re-subscribe to all the
events whenever an interface is re-enabled or added.
Signed-off-by: Jouni Malinen <j@w1.fi>
Configure the GO CTWindow on APstart if the driver supports it and this
parameter is set in wpa_supplicant configuration.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Add fixed_freq=<0/1> network block parameter and pass it to the driver
when starting or joining an IBSS. If this flag is set, IBSS should not
try to look for other IBSS networks to merge with on different channels.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
RTM_NEWLINK event without IFF_UP were processed for all related
interfaces (including VLANs and bridge). While these events may need to
be processed for other purposes, they should not end up claiming that
the main interface has been disabled, so indicate
EVENT_INTERFACE_DISABLED only if the ifname matches the first BSS ifname
for the interface. In addition, fix some of the ifup/down checks from
if_indextoname() cases to actually use the resolved ifname (namebuf)
rather than hardcoding the first configured ifname to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a step towards enabling hostapd to restart AP mode functionality
if the interface is disabled and re-enabled, e.g., with ifconfig down
and up. This commit takes care of beaconining only which may be
sufficient for open mode connection, but not for WPA2 cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds testing code (for CONFIG_TESTING_OPTIONS=y builds only) to
send an nl80211 vendor command and report a test vendor event in case
the driver supports this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 5a2a6de6a5 ('mesh: Make inactivity
timer configurable') has a problem on 32 bit systems. Setting
NL80211_MESHCONF_PLINK_TIMEOUT to 0xffffffff causes expiration of STA in
a minute by NL80211_CMD_DEL_STATION event. this is the kernel rule for
STA expiration:
(current jiffies) > (frame Rx jiffies + NL80211_MESHCONF_PLINK_TIMEOUT * 250)
On a 32 bit system, the right side could overflow and be unexpected
small value if NL80211_MESHCONF_PLINK_TIMEOUT is sufficiently large. STA
expiration occurs by this reason.
This patch solves the problem by disabling the STA expiration
functionality in mac80211. However, old kernel does not support
disabling it. If so, this patch sets mac80211 inactivity timer 60
seconds into future from the wpa_supplicant inactivity timer.
And I mis-understood that mesh_max_inactivity=0 disables inactivity
timer in wpa_supplicant. This commit fixes it also.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Commit 630b3230c8 ('nl80211: Increase
netlink receive buffer size') added unconditional use of
nl_socket_set_buffer_size() which was not included in libnl 1.1. Fix use
of that old version by making this conditional on CONFIG_LIBNL20.
Signed-off-by: Jouni Malinen <j@w1.fi>
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.
Signed-off-by: Jouni Malinen <j@w1.fi>
The correct nl80211 flag for group key management cipher was set only
for BIP (AES-CMAC-128). The same flag needs to be used with the newer
ciphers BIP-CMAC-256, BIP-GMAC-128, and BIP-GMAC-256.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
libnl uses a pretty small buffer (32 kB that gets converted to 64 kB) by
default. It is possible to hit that limit in some cases where operations
are blocked, e.g., with a burst of Deauthentication frames to hostapd
and STA entry deletion. Try to increase the buffer to make this less
likely to occur.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Current mesh code uses ap_max_inactivity as inactivity timer. This patch
makes it configurable.
There is another mesh inactivity timer in mac80211. The timer works even
if user_mpm=1. So this patch sets the max value to the timer for
workaround.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
If the inactivity check returns that there is no entry remaining for the
STA in the kernel, drop the STA in hostapd as well.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
