This adds support to hostapd for configuring airtime policy settings for
stations as they connect to the access point. This is the userspace
component of the airtime policy enforcement system PoliFi described in
this paper: https://arxiv.org/abs/1902.03439
The Linux kernel part has been merged into mac80211 for the 5.1 dev
cycle.
The configuration mechanism has three modes: Static, dynamic and limit.
In static mode, weights can be set in the configuration file for
individual MAC addresses, which will be applied when the configured
stations connect.
In dynamic mode, weights are instead set per BSS, which will be scaled
by the number of active stations on that BSS, achieving the desired
aggregate weighing between the configured BSSes. Limit mode works like
dynamic mode, except that any BSS *not* marked as 'limited' is allowed
to exceed its configured share if a per-station fairness share would
assign more airtime to that BSS. See the paper for details on these
modes.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
This provides a mechanism for configuring per-STA airtime weight for
airtime policy configuration.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
This allows authenticator side to complete FT initial mobility domain
association using FT-EAP with PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When completing FT initial mobility domain association with EAP, store
XXKey/MPMK in the PMKSA cache instead of MSK. The previously stored MSK
was of no use since it could not be used as the XXKey for another FT
initial mobility domain association using PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is apparently possible to somehow trigger the driver to report a
channel switch event during ACS operation when the interface information
is not yet complete. hapd->iface->current_mode could be NULL in that
case and that would result in process termination due to NULL pointer
dereference.
It should not really be possible to trigger a channel switch during ACS
is running (i.e., before the AP mode operation has been started), but
since that has been seen in an arbitrary test sequence with interface
start/stop operations with various parameters (both valid and invalid),
better prevent a crash here by ignoring the unexpected event instead of
trying to process it.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Unexpected CHAN_SWITCH command could get this function using a NULL
pointer if the channel switch was requested while the interface was
already disabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
driver->hapd_deinit() is going to free the memory that the cached
pointers are pointing to, so clear the pointers to avoid possibility of
dereferencing used memory. It seemed to be possible to hit a code path
using those fields by issuing a CHAN_SWITCH command on disabled hostapd
interface in some cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds a ieee80211ax=0/1 line to the STATUS output to indicate
the configuration of ieee80211ax, which similar to ieee80211n and
ieee80211ac.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The first four octets of the element were used as a host byte order u32.
That is not correct on bigendian CPUs, so handle byte swapping needs
properly. Mark the he_oper_params field as le32 to explicitly indicate
the byte order and swap the generated params content based on CPU byte
order.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The current code will always use the size required when all optional
elements are present. This will cause the Linux kernel to consider the
field to be malformed if the elements are not actually flagged as being
present.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
SPR allows us to detect OBSS overlaps and allows us to do adaptive CCA
thresholds. For this to work the AP needs to broadcast the element
first.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Properly populate the the HE Capabilities element with the info read
from the kernel.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
According to P802.11ax/D4.0 9.4.2.238 (HE Operation element) the BSS
Color Information field is located after the HE Operation Parameters
field. Fix the ordering of the bit masks/offsets for fields in these 3+1
octets used as a single 32-bit value. With these changes, Wireshark 3.2
is able to properly parse and display Beacon frames.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
IEEE P802.11ax/D4.0 9.4.2.243 "HE Operation element" indicates that the
special value 1023 in the TXOP Duration RTS Threshold field is used to
indicate that TXOP duration-based RTS is disabled. Use that value as the
default instead of the previously used value 0 which would really mean
threshold of 0 usec. Furthermore, the previous implementation did not
allow values larger than 255 to be used for this field while the field
is actually 10 bits in size.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This makes it easier to upper layer components to manage operating
channels in cases where the same radio is shared for both station and AP
mode virtual interfaces.
Signed-off-by: Omer Dagan <omer.dagan@tandemg.com>
Logs involving IEEE 802.11 Status Codes output the Status Code value,
but do not provide any explanation of what the value means. This change
provides a terse explanation of each status code using the latter part
of the Status Code #define names.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
The new hostapd configuration parameter dpp_controller can now be used
with the following subparameter values: ipaddr=<IP address>
pkhash=<hexdump>. This adds a new Controller into the configuration
(i.e., more than one can be configured) and all incoming DPP exchanges
that match the specified Controller public key hash are relayed to the
particular Controller.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not try to derive a PMK-R0 and PMK-R1 again for the case where an
association was started with FT protocol and PTK is rekeyed using 4-way
handshake. Instead, use the previously derived PMK-R1 to allow a new PTK
to be derived.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not try to derive a PMKID for EAPOL-key msg 1/4 when going through
4-way handshake to rekey PTK during an association that was started
through FT protocol.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to allow PTK rekeying to be performed through 4-way
handshake in an association started through FT protocol.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to avoid leaving some timers (e.g., for PTK rekeying)
running afrer a STA has disassociated.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
FT rules for PTK derivation do not use PMK. Remove the unused argument
to the PTK derivation function.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The PMK and PMKID information from FILS ERP and FILS PMKSA caching needs
to be stored within struct wpa_state_machine for PTK to work. Without
this, PTK derivation would fail and attempt to go through rekeying would
result in disconnection. Furthermore, wpa_rekey_ptk() timer needs to be
started at the completion of FILS association since the place where it
was done for non-FILS cases at the end of 4-way handshake is not reached
when FILS authentication is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is possible for the SAE state machine to remove the STA and free the
sta pointer in the mesh use cases. handle_auth_sae() could have
dereferenced that pointer and used freed memory in some cases. Fix that
by explicitly checking whether the STA was removed.
Fixes: bb598c3bdd ("AP: Add support for full station state")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
ap_free_sta() frees the sta entry, so sta->addr cannot be used after
that call. Fix the sequence of these two calls to avoid use of freed
memory to determine which PMKSA cache entry to remove.
Fixes: 9f2cf23e2e ("mesh: Add support for PMKSA caching")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The external authentication command and event does not need to copy the
BSSID/SSID values into struct external_auth since those values are used
before returning from the call. Simplify this by using const u8 * to
external data instead of the array with a copy of the external data.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend commit 5ff39c1380 ("SAE: Support external authentication
offload for driver-SME cases") to support external authentication
with drivers that implement AP SME by notifying the status of
SAE authentication to the driver after SAE handshake as the
driver acts as a pass through for the SAE Authentication frames.
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
beacon_set_done did not get reset to zero on disabling interface using
DISABLE control interface command and the subsequent ENABLE command will
caused configuration of Beacon/Probe Response/Association Response frame
IEs twice. The unnecessary two step configuration can be avoided by
resetting beacon_set_done on DISABLE so that ENABLE can bring up the
interface in a single step with fully updated IEs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
identity_buf may be NULL here. Handle this case explicitly by printing
"N/A" instead relying on snprintf converting this to "(null)" or some
other value based on unexpected NULL pointer.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Avoid duplicated code in each user of dpp_build_conf_req() by moving the
common encapsulation case into this helper function.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When connected using FT-SAE key mgmt, use PMK from PMKSA cache as XXKey
for PMK-R0 and PMK-R1 derivations. This fixes an issue where FT key
hierarchy could not be established due to missing (not yet configured)
XXKey when using SAE PMKSA caching for the initial mobility domain
association.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Ethernet frames have minimum length of 64 octets and shorter frames may
end up getting arbitrary padding in the end. This would result in the
FT/RRB receiver rejecting the frame as an incorrectly protected one.
Work around this by padding the message so that it is never shorter than
the minimum Ethernet frame.
Unfortunately, this padding is apparently not enough with all Ethernet
devices and it is still possible to see extra two octet padding at the
end of the message even if larger frames are used (e.g., showed up with
128 byte frames). For now, work around this by trying to do AES-SIV
decryption with two octets shorter frame (ignore last two octets) if the
first attempt fails.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Merge the practically copy-pasted implementations in wpa_supplicant and
hostapd into a single shared implementation in dpp.c for managing
configurator and boostrapping information. This avoid unnecessary code
duplication and provides a convenient location for adding new global DPP
data.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The memcpy calls added for exposing the PMK from wpa_auth module could
end up trying to copy the same memory buffer on top of itself.
Overlapping memory areas are not allowed with memcpy, so this could
result in undefined behavior. Fix this by making the copies conditional
on the updated value actually coming from somewhere else.
Fixes: b08c9ad0c7 ("AP: Expose PMK outside of wpa_auth module")
Signed-off-by: Jouni Malinen <j@w1.fi>
This code was after the FILS handling that would have encrypted the
frame. While FILS and OWE are never used together, the OWE handling
should really be before the FILS handling since no IEs can be added
after the FILS encryption step. In addition, the Diffie-Hellman
Parameter element is not a Vendor Specific element, so it should be
before some of the Vendor Specific elements even though it is not
defined in IEEE 802.11.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use Diffie-Hellman key exchange to derivate additional material for
PMK-to-PTK derivation to get PFS. The Diffie-Hellman Parameter element
(defined in OWE RFC 8110) is used in association frames to exchange the
DH public keys. For backwards compatibility, ignore missing
request/response DH parameter and fall back to no PFS in such cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
DPP allows Diffie-Hellman exchange to be used for PFS in PTK derivation.
This requires an additional Z.x (x coordinate of the DH shared secret)
to be passed to wpa_pmk_to_ptk(). This commit adds that to the function
and updates all the callers to pass NULL,0 for that part in preparation
of the DPP specific changes to start using this.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous OWE implementation on the AP side rejected any
(Re)Association Request frame with the Diffie-Hellman Parameter element
if AKM was not OWE. This breaks compatibility with DPP PFS, so relax
that rule to allow DPP AKM to be used as well. While this commit alone
does not add support for PFS, this allows interoperability between
non-PFS implementation on the AP and a newer PFS implementation on the
STA.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Share a single parsing implementation for both hostapd and
wpa_supplicant to avoid code duplication. In addition, clean up the
implementation to be more easily extensible.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The queue_len * 50 ms wait time was too large with the retransmission
timeouts used in the mesh case for SAE. The maximum wait of 750 ms was
enough to prevent successful completion of authentication after having
hit the maximum queue length. While the previous commit is enough to
allow this to complete successfully in couple of retries, it looks like
a smaller wait time should be used here even if it means potentially
using more CPU.
Drop the processing wait time to queue_len * 10 ms so that the maximum
wait time is 150 ms if the queue is full.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous design of simply queuing all SAE commit messages was not
exactly good at allowing recovery from a flooding state if the valid
peer used frequent retransmissions of the SAE message. This could
happen, e.g., with mesh BSSs using SAE. The frequent retransmissions and
restarts of SAE authentication combined with SAE confirm messages
bypassing the queue ended up in not being able to finish SAE exchange
successfully.
Fix this by modifying the queuing policy to queue SAE confirm messages
if there is a queued SAE commit message from the same peer so that the
messages within the same exchange do not get reordered. In addition,
replace queued SAE commit/confirm message if a new matching message is
received from the same peer STA. This is useful for the case where the
peer restarts SAE more quickly than the local end has time to process
the queued messages.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use this new message from Enrollee to Configurator to indicate result of
the config object provisioning if both devices support protocol version
2 or newer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Derive PMKR1Name during the FILS authentication step, verify that the
station uses matching PMKR1Name in (Re)Association Request frame, and
add RSNE[PMKR1Name] into (Re)Association Response frame when going
through FT initial mobility domain association using FILS. These steps
were missed from the initial implementation, but are needed to match the
IEEE 802.11ai requirements for explicit confirmation of the FT key
hierarchy (similarly to what is done in FT 4-way handshake when FILS is
not used).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This gets rid of a confusing error message "FILS: Failed to add PMKSA
cache entry based on ERP" for cases where PMKSA caching is disabled in
hostapd (disable_pmksa_caching=1). Functionality remains unchanged,
i.e., no cache entry was added before this change either.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd configuration parameters fragm_threshold and rts_threshold were
documented to disable the threshold with value -1 and not change driver
configuration if the parameter is not included. However, -1 was mapped
into not changing the driver value, so the explicit disabling part did
not work.
Replace the default values for these to be -2 so that explicitly set
configuration value -1 can be distinguished from the case of not
including the parameter. Map the -1 value to a driver request to disable
the threshold. Ignore any error from this operation just in case to
avoid breaking functionality should some drivers not accept the (u32) -1
value as a threshold value request to disable the mechanism.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This patch added 'check_cert_subject' support to match the value of
every field against the DN of the subject in the client certificate. If
the values do not match, the certificate verification will fail and will
reject the user.
This option allows hostapd to match every individual field in the right
order, also allow '*' character as a wildcard (e.g OU=Development*).
Note: hostapd will match string up to 'wildcard' against the DN of the
subject in the client certificate for every individual field.
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Jared Bents <jared.bents@rockwellcollins.com>
Signed-off-by: Jouni Malinen <j@w1.fi>
