According to IEEE P802.11ax/D6.0, 11.1.4.3.4 (Criteria for sending a
response), AP should answer Probe Request frames if either SSID or Short
SSID matches. Implement this part of the Short SSID use for the BSS (the
collocated 6 GHz BSS case is not covered in this commit).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Use op_class to derive channel width for the operating channel when
op_class is configured by the user in both fixed channel and ACS cases.
We can avoid using ht_capab field to derive channel width especially in
the 6 GHz band in which only HE is supported.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to exclude non-PSC 6 GHz channels from the input frequency
list to ACS. The new acs_exclude_6ghz_non_psc=1 parameter can be used by
6 GHz only APs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update new channels in Channel Bonding (CB2 ... CB4) in the 60 GHz band
for different regulatory regions according to the latest draft amendment
IEEE P802.11ay/D5.0.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
When operating on the 6 GHz band, add 6 GHz Operation Information inside
the HE Operation element and don't publish HT/VHT IEs.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
- Replace HOSTAPD_MODE_IEEE80211AX mode checks with is_6ghz_op_class()
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Add support for new hardware mode for 6 GHz band. 6 GHz operation is
defined in IEEE P802.11ax/D4.3. 6 GHz band adds global operating classes
131-135 that define channels in frequency range from 5940 MHz to 7105
MHz.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
- Remove HOSTAPD_MODE_IEEE80211AX mode
- Replace check for HOSTAPD_MODE_IEEE80211AX with is_6ghz_freq()
- Move center_idx_to_bw_6ghz() to ieee802_11_common.c file
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Logs involving IEEE 802.11 Status Codes output the Status Code value,
but do not provide any explanation of what the value means. This change
provides a terse explanation of each status code using the latter part
of the Status Code #define names.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
Logs involving IEEE 802.11 Reason Codes output the Reason Code value,
but do not provide any explanation of what the value means. This change
provides a terse explanation of each Reason Code using the latter part
of the reason code #define names.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
Rather than always iterating elements from frames with pure
u8 pointers, add a type "struct element" that encapsulates
the id/datalen/data format of them.
Then, add the element iteration macros
* for_each_element
* for_each_element_id
* for_each_element_extid
which take, as their first 'argument', such a structure and
iterate through a given u8 array interpreting it as elements.
While at it also add
* for_each_subelement
* for_each_subelement_id
* for_each_subelement_extid
which instead of taking data/length just take an outer element
and use its data/datalen.
Also add for_each_element_completed() to determine if any of
the loops above completed, i.e., it was able to parse all of
the elements successfully and no data remained.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These are not allowed in ISO C++ (and well, not really in ISO C either,
but that does not result in compiler warning without pedantic
compilation).
Since ieee802_11_common.h may end up getting pulled into C++ code for
some external interfaces, it is more convenient to keep it free of these
cases. Pull in ieee802_11_defs.h to get enum phy_type defined and move
enum chan_width to common/defs.h (which was already pulled in into
src/drivers/driver.h and src/common/ieee802_11_common.h).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new ieee802_11_ext_capab() and wpa_bss_ext_capab() functions can be
used to check whether a specific extended capability bit is set instead
of having to implement bit parsing separately for each need.
Signed-off-by: Jouni Malinen <j@w1.fi>
An AP might refuse to connect a STA if it has a low RSSI. In such case,
the AP informs the STA with the desired RSSI delta and a retry timeout.
Any subsequent association attempt with that AP (BSS) should be avoided,
unless the RSSI level improved by the desired delta or the timeout has
expired.
Defined in Wi-Fi Alliance Optimized Connectivity Experience technical
specification v1.0, section 3.14 (RSSI-based association rejection
information).
Signed-off-by: Beni Lev <beni.lev@intel.com>
The purpose of Multi-AP specification is to enable inter-operability
across Wi-Fi access points (APs) from different vendors.
This patch introduces one new configuration parameter 'multi_ap' to
enable Multi-AP functionality and to configure the BSS as a backhaul
and/or fronthaul BSS.
Advertise vendor specific Multi-AP capabilities in (Re)Association
Response frame, if Multi-AP functionality is enabled through the
configuration parameter.
A backhaul AP must support receiving both 3addr and 4addr frames from a
backhaul STA, so create a VLAN for it just like is done for WDS, i.e.,
by calling hostapd_set_wds_sta(). Since Multi-AP requires WPA2 (never
WEP), we can safely call hostapd_set_wds_encryption() as well and we can
reuse the entire WDS condition.
To parse the Multi-AP Extension subelement, we use get_ie(): even though
that function is meant for parsing IEs, it works for subelements.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This adds two utility functions to convert both operating classes and
and the chan_width enum to an integer representing the channel
bandwidth. This can then be used to compare bandwidth parameters in an
uniform manner.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This function can be used to easily convert the parameters returned
by the channel_info driver API, into their corresponding operating
class and channel number.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This extends the SAE implementation in both infrastructure and mesh BSS
cases to allow an optional Password Identifier to be used. This uses the
mechanism added in P802.11REVmd/D1.0. The Password Identifier is
configured in a wpa_supplicant network profile as a new string parameter
sae_password_id. In hostapd configuration, the existing sae_password
parameter has been extended to allow the password identifier (and also a
peer MAC address) to be set. In addition, multiple sae_password entries
can now be provided to hostapd to allow multiple per-peer and
per-identifier passwords to be set.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Mark a channel as required DFS based on regulatory information received
from the driver/kernel rather than deciding based on hardcoded
boundaries on the frequency. Previously few channels were being marked
as requiring DFS even though they were non-DFS in a particular country.
If the driver does not provide channel list information, fall back to
the previously used frequency-based determination.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd processing of (Re)Association Request frames to
store a local copy of the Consortium OI within the Roaming Consortium
Selection element, if present, and then add that in HS 2.0 Roaming
Consortium attribute into RADIUS Access-Request messages.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This provides access to the Minimum/Maximum Transmit Power Capabilitie
fileds (the nominal minimum/maximum transmit power with which the STA
is capable of transmitting in the current channel; signed integer in
units of decibels relative to 1 mW).
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
This allows CONFIG_TESTING_OPTIONS=y builds of wpa_supplicant to
override the OWE DH Parameters element in (Re)Association Request frames
with arbitrary data specified with the "VENDOR_ELEM_ADD 13 <IE>"
command. This is only for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a helper function that parses candidate list from command line
arguments.
This function will be used (in the following commits) to add
a candidate list to BSS transition management query.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a function to get operating class definition (including bandwidth,
channel numbers, etc.) from the operating class number and country.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add helper function that converts non-global operating classes to global
operating classes according to IEEE Std 802.11-2016, Annex E.
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
This adds definitions for new information elements from P802.11ai/D11.0
and parsing of these IEs.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Save RM enabled capability element of an associating station if radio
measurement is supported in its capability field.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
This makes hostapd track Supported Operating Classes information from
the associated STAs. The stored information is available through the STA
control interface command (supp_op_classes row) as a hexdump of the
Supported Operating Classes element starting from the Length field. This
information can be used as input to BSS transition management and
channel switching decisions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a function to derive phy type from frequency and bandwidth
as defined in IEEE Std 802.11ac-2013 Annex C (dot11PHYType).
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add definitions for global operating classes. These definitions will be
used to construct supported operating classes information element.
The operating classes definitions used locally for P2P module will be
removed and included in the general operating classes definitions.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a helper function to find a certain IE inside IEs buffer by ID and
use this function in several places that implemented similar
functionality locally.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add ieee80211_freq_to_channel_ext() conversion function into
ieee802_11_common.c. This function converts freq to channel and
additionally computes operating class, based on provided HT and VHT
parameters.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This adds parsing of QCA vendor specific elements and as the first such
element to be parsed, stores pointers to the preferred frequency list
element that can be used to enhance P2P channel negotiation behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Remove the length field from struct ieee802_11_elems since the only
allowed element length is five and that is checked by the parser.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the only allowed element length is one.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the only allowed element length is one.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add handling logic for DFS offloaded case, and add a helper function
that takes the frequency (MHz) as a param and returns 1 if given channel
requires DFS, or 0 otherwise.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows vendor specific information element to be used to advertise
support for VHT on 2.4 GHz band. In practice, this is used to enable use
of 256 QAM rates (VHT-MCS 8 and 9) on 2.4 GHz band.
This functionality is disabled by default, but can be enabled with
vendor_vht=1 parameter in hostapd.conf if the driver advertises support
for VHT on either 2.4 or 5 GHz bands.
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
ieee80211_chan_to_freq() is a generic function that replaces and extends
the previous P2P-specific p2p_channel_to_freq(). The new function
supports both the global operating class table as well as the additional
US, EU, JP, and CN operating class tables.
Signed-off-by: Jouni Malinen <j@w1.fi>
