The construction used here to figure out the offset of variable length
IEs in Probe Request frames was a bit odd looking and resulted in a
warning from a static analyzer, so replace it with more standard use of
offsetof().
Signed-off-by: Jouni Malinen <j@w1.fi>
p2p_process_nfc_connection_handover() allocates msg memory in the parser
and might return before memory is released if the received message is
not valid.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
org.wi-fi.wfds service is not a replacement for non-WFA service matches.
Do not try to replace the results with that if there is not sufficient
room for the response. Instead, reply with all the matching services
that fit into the message. org.wi-fi.wfds is the first entry in the list
(if matching request/service is present), so it won't get overridden by
other services.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The service hash for org.wi-fi.wfds is supposed to match only if the
device has a WFA defined org.wi-fi.wfds.* service. Verify that before
adding org.wi-fi.wfds to the response.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Probe Response building is already doing service matching and there is
no need to do this in both places, so simplify the p2p_reply_probe()
implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When doing initial processing of Probe Request frame service hashes, the
previous implementation dropped all other hash values if a hash for
org.wi-fi.wfds was included. This is not correct, since that is not a
full wildcard of all services (it only matches WFA defined
org.wi-fi.wfds.* services).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This "wildcard" match is for WFA specified org.wi-fi.wfds.* services,
not for all services. Verify that there is a really matching service
being advertised instead of assuming this "wildcard" matches if any
services are advertised.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The org.wi-fi.wfds "wildcard" is not a full wildcard of all service
names and as such, it must not remove other service name hash values
from the Probe Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
p2ps_gen_hash() has a limit on service names based on the temporary
buffer from stack. Verify that the service name from the local P2P_FIND
command is short enough to fix into that buffer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Quoting P2PS specification: "If multiple Service Hash values are
included in the Probe Request frame, then the ASP shall find a match for
each Service Hash, and it shall send a Probe Response frame with the
information listed in this section for all matched Service Hashes." This
commit changes handling of wildcard hash matching by adding a
wildcard 'org.wi-fi.wfds' info together with the other hash matches.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add auxiliary functions to write a single advertised service info record
into a wpabuf and to find P2PS wildcard hash in a received hash
attribute. Re-factor p2p_buf_add_service_instance() function to allow
adding new wildcard types in future commits.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Avoid using p2p_data::query_hash for both Probe Request frame processing
and for hashes specified by p2p_find. It's resolved by use of local
query_hash and query_count variables in p2p_reply_probe().
Since p2p_data::query_hash is used only for seek hash values rename
p2p_data::query_hash to p2ps_seek_hash.
Delete p2p_data::query_count since it's not needed anymore.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Commit 86bd36f0d5 ('Add generic mechanism
for adding vendor elements into frames') introduced a mechanism to add
vendor elements into various frames, but missed the addition to the
Invitation Response frame. This commit addresses the same.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This variable is used locally only in the p2p_reply_probe() function.
The value of this variable is valid only in the context of the single
Probe Request message handling and doesn't make much sense in p2p
context.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Free a PD context with a function encapsulating both os_free() call and
setting a PD context pointer to NULL.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
A P2P Client may be discoverable and reply to Probe Request frames,
while at the same time the P2P GO would also be discoverable and include
the P2P Client information in the P2P Group Info attribute of the Probe
Response frames.
If a seeker constantly hears the Probe Response frames from a P2P Client
and then from the GO, but handles them in the opposite order (due to
scan results ordering), the more valuable Probe Response frame from the
P2P Client will be ignored. Fix this by defining a threshold (1 second)
during which the direct Probe Response frame will be preferred over the
information acquired from the GO and will not be considered as old.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When adding group clients to the P2P peer list, use the driver provided
BSS entry timestamp instead of the current time. Otherwise, the time
comparison which is made in p2p_add_device() doesn't make sense.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
If the RX frequency of the Probe Request frame is known, specify it when
sending the Probe Response frame. This is needed when the Probe Request
frame is received on another virtual interface, for example, when a GO
or P2PS client are discoverable on the group operating channel.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Return P2P_PREQ_PROCESSED instead of P2P_PREQ_NOT_PROCESSED on
a successful Probe Request frame handling in p2p_reply_probe().
Verify a return value of p2p_reply_probe() in p2p_probe_req_rx()
and continue a pending invitation/connection flow only if the
Probe Request frame is from an expected P2P peer.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
In some cases, Probe Request frames can be received by a peer not only
on a listen channel. In this case an additional rx_freq parameter
explitly contains a Probe Request frame RX frequency. In case rx_freq is
set to 0, a Probe Request frame RX channel is assumed to be our own
listen channel (p2p->cfg->channel).
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add operating class 125 (channels 149..169) to the list of P2P supported
channels. This allows the 5 GHz channels 161 and 169 to be used for P2P
GO when those channels are allowed for AP mode in the current regulatory
domain.
Signed-off-by: Amr BEN ABDESSALEM <amrx.ben.abdessalem@intel.com>
Add GO Intent information of connecting device in GO Negotiation Request
event which will help applications to decide its own GO intent value in
advance and can avoid failure cases when both devices use GO Intent 15
depending on application requirement.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Do not add a P2P IE when a station interface is trying to associate
to an AP or P2P GO that publishes a P2P IE but does not include
a P2P manageability attribute.
This addresses an interoperability issue that was reported in
https://bugzilla.kernel.org/show_bug.cgi?id=96471, where a P2P GO
rejects association from a station interface without a specified
reason.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This enforces variable length strings Manufacturer, Model Name, Model
Number, and Serial Number to be within the maximum length defined in the
WSC specification. While none of the existing users for these within
hostapd/wpa_supplicant had problems with longer strings, it is good to
ensure the strings are not longer to avoid potential issues at higher
layer components.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the only allowed element length is one.
Signed-off-by: Jouni Malinen <j@w1.fi>
This program can be used to run fuzzing tests for areas related to P2P
message parsing and processing. p2p-fuzzer allows data files to be used
to inject Probe Response and Action frames for processing by the P2P
module.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it more obvious that the wps_parse_msg() bounds checking is
used to verify that there is sufficient space in the P2P buffer for the
secondary device types.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This modifies couple of code segments that replaced control characters
in strings with '_' to use a common helper function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While none of the current users of msg.persistent_ssid{,_len} would have
issues with too long SSID value, it is safer to enforce bounds checking
on the SSID while parsing the attribute to avoid any potential issues in
the future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes a possible memcpy overflow for P2P dev->oper_ssid in
p2p_add_device(). The length provided by the peer device (0..255 bytes)
was used without proper bounds checking and that could have resulted in
arbitrary data of up to 223 bytes being written beyond the end of the
dev->oper_ssid[] array (of which about 150 bytes would be beyond the
heap allocation) when processing a corrupted management frame for P2P
peer discovery purposes.
This could result in corrupted state in heap, unexpected program
behavior due to corrupted P2P peer device information, denial of service
due to process crash, exposure of memory contents during GO Negotiation,
and potentially arbitrary code execution.
Thanks to Google security team for reporting this issue and smart
hardware research group of Alibaba security team for discovering it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Delete all ASP serice advertisement on wpas_p2p_service_flush similarly
to Bonjour and UPnP services.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
It was possible for the GO Negotiation Response (failure) TX status to
be processed at a point where there is no P2P timeout to continue
search. Avoid stopping the ongoing search operation by explicitly
restarting it from this callback.
Signed-off-by: Jouni Malinen <j@w1.fi>
The optional freq=<MHz> can now be used with the P2P_FIND command to
specify a single channel to scan during the first round of P2P search.
For example, this can be used to replace the full initial scan with a
single channel scan of a known operation channel.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
This reverts commit 3df2f4fe99 ('P2P:
Remove unused P2P_SCAN_SPECIFIC') with a modification to fit the current
code base.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
It is possible for an Action frame TX operation to be stopped in a way
that results in the TX status callback function not being called. This
could happen, e.g., when P2P_STOP_FIND was issued while waiting for PD
Response TX status. This specific case ended in leaving
p2p->send_action_in_progress set to 1 and that ending up stopping a
future TX operation when p2p_send_action_cb() gets called with
p2p->pending_action_state == P2P_NO_PENDING_ACTION.
This could result in reception of a fragmented service discovery
response failing due to the GAS sequence getting stopped when receiving
TX callback for the first GAS comeback request. That sequence could be
hit in mac80211_hwsim tests when p2p_listen_and_offchannel_tx was
followed by p2p_service_discovery_fragmentation (even after a long time
since this was on dev1 and there could be even 10 minutes between these
test cases).
Fix this issue by clearing send_action_in_progress whenever stopping
pending P2P operation with p2p_stop_find (or P2P_FLUSH for that matter).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If p2p_find_timeout triggers after starting SD but before getting TX
status for send action, unwanted search could get triggered again when
TX status arrives though p2p_find_timeout moved the state to P2P_IDLE by
then. p2p_continue_find() would then move the state to P2P_SEARCH again.
Do not trigger the find operation from this context if state is
P2P_IDLE to avoid this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not claim to change the Listen channel in a debug message when
previously configured channel prevents this. In addition, fix a typo in
another related debug print.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_timeout_prov_disc_req is getting triggered in P2P_IDLE,
P2P_SEARCH and P2P_LISTEN_ONLY states. Retry logic should not be
limited to only P2P_IDLE state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
During service discovery if P2P_FIND times out, P2P_FIND_STOPPED event
is sent to upper layers to allow follow up P2P_FIND commands. This needs
to be done also in case an SD was in progress during the find operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This introduces a P2P module callback function that will be used to
create the pending P2PS group after sending PD Response and receiving
ACK status for it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When the peer device is trying to form a new group despite having
old persistent group with same roles, remove the stale persistent
group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpas_p2p_prov_disc() implementation to accept P2PS
parameters. None of the callers are yet using this functionality; the
following commit introduces a user.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a data structure for storing P2PS PD information and code to
add the related attributes into PD Request. The actual operation to
trigger this behavior will be added in a separate commit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
