Commit graph

604 commits

Author SHA1 Message Date
Ahmad Masri
86c998d37a FT: Add FT auth algorithm to connect params when roaming
Add WPA FT auth to connect params in case of a re-connection to ESS
supporting FT when FT was used in the first connect.

Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
2018-04-20 00:35:41 +03:00
Ahmad Masri
3dc3afe298 FT: Add MDE to assoc request IEs in connect params
Add MDE (mobility domain element) to Association Request frame IEs in
the driver assoc params. wpa_supplicant will add MDE only if the network
profile allows FT, the selected AP supports FT, and the mobility domain
ID matches.

Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
2018-04-20 00:32:49 +03:00
Jouni Malinen
4204669c69 HS 2.0: Add Roaming Consortium Selection element into AssocReq
This makes wpa_supplicant add Hotspot 2.0 Roaming Consortium Selection
element into (Re)Association Request frames if the network profile
includes roaming_consortium_selection parameter.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-18 01:12:25 +03:00
Dmitry Lebed
37547ad63c wpa_supplicant: Increase authentication timeout if CAC is started
Timeout is increased by dfs_cac_ms from channel data, or by max CAC time
(10 minutes) if dfs_cac_ms is not defined. This is needed for some more
complex cases, e.g., when STA is acting as an active slave with DFS
offload enabled and decided to start CAC after receiving CONNECT
command, in such a case the 10 second timeout is too small and
wpa_supplicant need to wait for CAC completion or CAC timeout (up to 10
minutes).

Without such timeout modification wpa_supplicant will be unable to
connect to an AP on DFS channel, since the default authentication
timeout (10 s) is smaller than the minimum CAC time (60 s).

Tested with nl80211 DFS offload implementation.

Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
2018-04-15 22:20:49 +03:00
Jouni Malinen
852b2f2738 SAE: Only allow SAE AKMP for PMKSA caching attempts
Explicitly check the PMKSA cache entry to have matching SAE AKMP for the
case where determining whether to use PMKSA caching instead of new SAE
authentication. Previously, only the network context was checked, but a
single network configuration profile could be used with both WPA2-PSK
and SAE, so should check the AKMP as well.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-04-09 19:34:44 +03:00
Jouni Malinen
06b1a10434 SAE: Fix default PMK configuration for PMKSA caching case
The RSN supplicant state machine PMK was set based on WPA PSK even for
the cases where SAE would be used. If the AP allows PMKSA caching to be
used with SAE, but does not indicate the selected PMKID explicitly in
EAPOL-Key msg 1/4, this could result in trying to use the PSK instead of
SAE PMK. Fix this by not setting the WPA-PSK as default PMK for SAE
network profiles and instead, configuring the PMK explicitly from the
found PMKSA cache entry.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-04-09 13:10:08 +03:00
Jouni Malinen
66dbc8d9c3 Add more debug prints for wpa_sm_set_pmk() calls
Couple of these were not preceded by wpa_hexdump_key(PSK) which made it
more difficult to interpret the debug log.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-04-08 19:11:07 +03:00
Davide Caratti
d89edb6112 wpa_supplicant: Don't reply to EAPOL if pkt_type is PACKET_OTHERHOST
When wpa_supplicant is running on a Linux interface that is configured in
promiscuous mode, and it is not a member of a bridge, incoming EAPOL
packets are processed regardless of the Destination Address in the frame.
As a consequence, there are situations where wpa_supplicant replies to
EAPOL packets that are not destined for it.

This behavior seems undesired (see IEEE Std 802.1X-2010, 11.4.a), and can
be avoided by attaching a BPF filter that lets the kernel discard packets
having pkt_type equal to PACKET_OTHERHOST.

Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
2018-04-02 12:21:27 +03:00
Vasyl Vavrychuk
8fb2b35735 Clean up setting of iface->p2p_mgmt flag
Previously we set this flag to one in wpa_supplicant_init_iface() if
Wi-Fi controller does not have a dedicated P2P-interface.

This setting had effect only in scope of wpa_supplicant_init_iface() and
it contradicts with comment to struct wpa_interface::p2p_mgmt field.
This comment says that this flag is used only if Wi-Fi controller has
dedicated P2P-device interface.

Also it contradicts with usage of similiar p2p_mgmt field in struct
wpa_supplicant. Again struct wpa_supplicant::p2p_mgmt is set only for
dedicated P2P-device interface.

After this change wpa_interface become input argument to
wpa_supplicant_init_iface() that we are not modifying.

Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
2018-04-02 12:13:59 +03:00
Masashi Honma
e480212765 dbus: Add FILS to global capabilities
If any of the interfaces supports FILS (and similarly for FILS-SK-PFS),
include the "fils" (and "fils_sk_pfs") capability in D-Bus information.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2018-04-02 11:56:06 +03:00
Jouni Malinen
6a252ece24 DPP: Fix GAS query removal race condition on DPP_STOP_LISTEN
If a DPP_STOP_LISTEN call happens to be received when there is a pending
gas-query radio work that has not yet been started, it was possible for
gas_query_stop() to go through gas_query_done() processing with
gas->work == NULL and that ended up with the pending GAS query getting
freed without removing the pending radio work that hold a reference to
the now freed memory. Fix this by removing the pending non-started radio
work for the GAS query in this specific corner case.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-02-07 18:03:58 +02:00
Jouni Malinen
3bd35b6816 wpa_supplicant: Fix parsing errors on additional config file
If the -I<config> argument is used and the referenced configuration file
cannot be parsed, wpa_config_read() ended up freeing the main
configuration data structure and that resulted in use of freed memory in
such an error case. Fix this by not freeing the main config data and
handling the error case in the caller.

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-02-04 12:20:13 +02:00
Jouni Malinen
9f8d459d4c OWE: Fix association IEs for transition mode open AP connection
The special case of returning from wpa_supplicant_set_suites() when OWE
transition mode profile is used for an open association did not clear
the wpa_ie buffer length properly. This resulted in trying to use
corrupted IEs in the association request and failed association
(cfg80211 rejects the request or if the request were to go out, the AP
would likely reject it).

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-02-04 11:55:01 +02:00
Sunil Dutt
5ff39c1380 SAE: Support external authentication offload for driver-SME cases
Extend the SME functionality to support the external authentication.
External authentication may be used by the drivers that do not define
separate commands for authentication and association
(~WPA_DRIVER_FLAGS_SME) but rely on wpa_supplicant's SME for the
authentication.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-02-02 21:17:55 +02:00
Jouni Malinen
c1790a5ff8 OWE: Allow station in transition mode to connect to an open BSS
If the OWE network profile matches an open network which does not
advertise OWE BSS, allow open connection. The new owe_only=1 network
profile parameter can be used to disable this transition mode and
enforce connection only with OWE networks.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-01-21 11:13:01 +02:00
Jouni Malinen
2cb40e9f40 OWE: Try all supported DH groups automatically on STA
If a specific DH group for OWE is not set with the owe_group parameter,
try all supported DH groups (currently 19, 20, 21) one by one if the AP
keeps rejecting groups with the status code 77.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-12-27 21:06:02 +02:00
vamsi krishna
d98038bb05 FILS: Driver configuration to disable/enable FILS features
The new disable_fils parameter can be used to disable FILS functionality
in the driver. This is currently removing the FILS Capability bit in
Extended Capabilities and providing a callback to the driver wrappers.
driver_nl80211.c implements this using a QCA vendor specific command for
now.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-12-15 20:52:17 +02:00
Jouni Malinen
5f30b69cde OWE: Allow DH Parameters element overriding with driver SME
Commit 265bda3444 ('OWE: Allow DH
Parameters element to be overridden for testing purposes') provided
means for using "VENDOR_ELEM_ADD 13 <IE>" in OWE protocol testing, but
that commit covered only the sme.c case (i.e., drivers that use
wpa_supplicant SME). Extend this to cover drivers that use internal SME
(e.g., use the nl80211 Connect command).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-12-11 13:59:55 +02:00
Jouni Malinen
7ed5337d8c Fix a typo in a debug message
This radio_work_free() message was missing the closing parenthesis.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-22 17:21:57 +03:00
Vidyullatha Kanchanapally
6338c99efa FILS: Send updated connection parameters to drivers if needed
After an initial connection wpa_supplicant derives ERP information which
can be used in doing eventual authentications in the same realm. This
information can be used by drivers with offloaded FILS support to do
driver/firmware initiated roamings. Add support to send this updated
information to such drivers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-18 01:19:42 +03:00
Vidyullatha Kanchanapally
d2ba0d719e Move assoc param setting into a helper function
This is needed to be able to use the same implementation for updating
the connection parameters in the driver during an association.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-18 01:19:42 +03:00
Jouni Malinen
daa4096084 Allow last (Re)Association Request frame to be replayed for testing
The new wpa_supplicant RESEND_ASSOC command can be used to request the
last (Re)Association Request frame to be sent to the AP to test FT
protocol behavior.

This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 17:47:24 +03:00
Jouni Malinen
a0bf1b68c0 Remove all PeerKey functionality
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.

This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.

Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 02:03:47 +03:00
Jouni Malinen
a34ca59e4d SAE: Allow SAE password to be configured separately (STA)
The new sae_password network profile parameter can now be used to set
the SAE password instead of the previously used psk parameter. This
allows shorter than 8 characters and longer than 63 characters long
passwords to be used.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-11 23:24:19 +03:00
Jouni Malinen
109704657d OWE: Support station SME-in-driver case
Previously, only the SME-in-wpa_supplicant case was supported. This
extends that to cover the drivers that implement SME internally (e.g.,
through the cfg80211 Connect command).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-09 12:35:14 +03:00
Jouni Malinen
e8b9649012 OWE: Transition mode support on station side
Add support for using the OWE Transition Mode element to determine the
hidden SSID for an OWE BSS that is used in transition mode.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-08 17:12:35 +03:00
Jouni Malinen
675112df1b OWE: Set PMK length properly on supplicant side
sm->pmk_len was not set when deriving the PMK as part of OWE key
generation. This depending on wpa_sm_set_pmk_from_pmksa() call resetting
the value to the default. While this worked for many cases, this is not
correct and can have issues with network profile selection based on
association information. For example, the OWE transition mode cases
would hit an issue here.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-08 17:12:35 +03:00
Jouni Malinen
61a56c1480 Add group_mgmt network parameter for PMF cipher selection
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-26 17:40:02 +03:00
Lior David
3c7863f812 wpa_supplicant: Support dynamic update of wowlan_triggers
Previously, wowlan_triggers were updated in kernel only during startup.
Also update it whenever it is set from the control interface.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-13 22:17:58 +03:00
Jouni Malinen
2efc672075 Fix RSN pre-authentication regression with pre-connection scan results
The introduction of radio works and a delayed callback to complete
association/connection requests ended up breaking RSN pre-authentication
candidate list generation for the case of pre-connection scan results.
Previously, wpa_supplicant_associate() set the RSN state machine
configuration before returning and the calls to
wpa_supplicant_rsn_preauth_scan_results() immediately after this
function call were working fine. However, with the radio work callback,
the RSN state machine configuration started to happen only in that
callback which would be called soon after this code path has completed.
This resulted in the RSN state machine not knowing the selected SSID and
as such, rejecting all pre-authentication candidates.

Fix this by setting the RSN state machine configuration from
wpa_supplicant_associate() so that the existing callers of
wpa_supplicant_rsn_preauth_scan_results() can be used as-is to add
candidates for pre-authentication.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-12 16:47:02 +03:00
Adiel Aloni
2c66c7d115 wpa_supplicant: Check length when building ext_capability in assoc_cb
When building wpa_ie in wpas_start_assoc_cb() with ext_capab,
make sure that assignment does not exceed max_wpa_ie_len.

Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
2017-09-10 22:16:06 +03:00
Saurav Babu
a39b040b4c dbus: Add MeshGroupRemoved signal
This is similar to the control interface event MESH-GROUP-REMOVED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-09 14:12:33 +03:00
Saurav Babu
89e9cd25d2 dbus: Add MeshGroupStarted signal
This introduces a new interface for mesh and adds a signal that
is similar to the control interface event MESH-GROUP-STARTED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-09 14:01:14 +03:00
Ashwini Patil
332aadb8a2 STA: Add OCE capability indication attribute
Add OCE capability indication attribute in Probe Request and
(Re)Association Request frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-14 21:19:53 +03:00
Vidyullatha Kanchanapally
b377ec2585 FILS: Fix issuing FILS connect to a non-FILS AP in driver-FILS case
If an AP is not FILS capable and wpa_supplicant has a saved network
block for the network with FILS key management and a saved erp info,
wpa_supplicant might end up issuing a FILS connection to a non-FILS AP.
Fix this by looking for the presence of FILS AKMs in wpa_s->key_mgmt,
i.e., after deciding on the AKM suites to use for the current
connection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-14 21:11:35 +03:00
Ashwini Patil
b04854ceff nl80211/MBO: Set temporary disallowed BSSID list to driver
Set temporary disallowed BSSID list to the driver so that the driver
doesn't try to connect to any of the blacklisted BSSIDs during
driver-based roaming operation. This commit includes support only for
the nl80211 driver interface using a QCA vendor command for this.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-30 17:27:44 +03:00
Jouni Malinen
a0d5c56f8b DPP: Network Introduction protocol for wpa_supplicant
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:59 +03:00
Jouni Malinen
567da5bbd0 DPP: Add new AKM
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
461d39af40 DPP: Configuration exchange
This adds support for DPP Configuration Protocol using GAS. Full
generation and processing of the configuration object is not included in
this commit.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:15 +03:00
Jouni Malinen
be27e185b7 DPP: Bootstrap information management
Add wpa_supplicant control interface commands for parsing the bootstrap
info URI from a QR Code (get peer public key) and to generate a new
bootstrap info with private key for local use. The optional
key=<hexdump> argument to the DPP_BOOTSTRAP_GEN command can be used to
specify the bootstrapping private key in OpenSSL ECPrivateKey DER
encoding format. This results in the local bootstrapping information
entry being created with the specified key instead of generating a new
random one.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 12:03:30 +03:00
Vidyullatha Kanchanapally
b5db6e5dc4 eap_proxy: Support multiple SIMs in get_imsi()
This allows the eap_proxy mechanism to be used with multiple SIMs by
following the configured sim_num to index which SIM to use for when
fetching the IMSI through eap_proxy.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-06 03:42:32 +03:00
Vasanthakumar Thiagarajan
aa56e36d66 driver: Make DFS domain information available to core
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
2017-05-13 20:01:44 +03:00
Purushottam Kushwaha
43a356b268 Provide option to configure BSSID hint for a network
This exposes user configurable option to set bssid_hint for a network.
bssid_hint indicates which BSS has been found a suitable candidate for
initial association for drivers that use driver/firmware-based BSS
selection. Unlike the bssid parameter, bssid_hint does not limit the
driver from selecting other BSSs in the ESS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-12 00:20:59 +03:00
Sunil Dutt
0661163eff Do not blacklist the current AP on DISABLE_NETWORK
Disconnection due to DISABLE_NETWORK while being connected was resulting
in the AP getting blacklisted. Avoid this by setting own_disconnect_req
on a disconnect request due to DISABLE_NETWORK similarly to the
SELECT_NETWORK disconnection case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-29 17:46:36 +03:00
Vidyullatha Kanchanapally
da6a28ba60 FILS: Specify if FILS HLP was sent in connect
This adds a string "FILS_HLP_SENT" to connect event when HLP is sent
as part of ASSOC/CONNECT request.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-29 16:35:23 +03:00
Vidyullatha Kanchanapally
a38090b16d FILS: Add HLP to Connect IEs
Add FILS HLP elements to Connect IEs and fragment them if necessary.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-29 16:35:21 +03:00
Vidyullatha Kanchanapally
1e6780bda9 Allocate dynamic memory for connect IEs
This is needed to allow new elements (e.g., FILS HLP request) to be
added.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-29 16:34:48 +03:00
Vidyullatha Kanchanapally
5538fc9309 FILS: Track completion with FILS shared key authentication offload
Update the internal fils_completed state when offloading FILS shared key
authentication to the driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
8b0a6dba87 FILS: Connect request for offloaded FILS shared key authentication
Add FILS/ERP parameters into the driver connect command to support FILS
shared key authentication offload.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
79f3121bb4 FILS: Set cache identifier in current PMKSA entry for driver-SME case
This was already done in sme_send_authentication() for the case where
wpa_supplicant SME is used. Similar change is needed for driver-SME to
allow FILS authentication to be offloaded to the driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00