Commit graph

261 commits

Author SHA1 Message Date
Dan Williams
3bd3257a0a dbus: add BSS Age property to indicate last-seen time
"Age" is the age in seconds since the BSS was last seen, and is
emitted as a PropertyChanged signal whenever the BSS is updated
from a scan result. It also returns the correct age when queried
directly.

This property can be used to resolve issues where, if no other
properties of the BSS changed from scan results (for example,
if the BSS always had 100% signal) no D-Bus signals would be
emitted to indicate that the BSS had just been seen in the scan.

Signed-hostap: Dan Williams <dcbw@redhat.com>
2014-09-07 19:18:45 +03:00
Eduardo Abinader
4aa9c156e5 dbus: Close dbus dict just after appending data
Before fixing this issue, calling wpas_dbus_getter_p2p_device_config
was causing early termination of dbus connection, due to writing
values to an already closed dict.

Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
2014-08-10 11:29:49 +03:00
Tomasz Bursztyka
4a0693a4d5 dbus: Declare and implement GroupFinished as for GroupStarted
First for better concistancy but also to tell about the group_object
that is getting removed, thus the client will know about it and will be
able to act accordingly.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-07-31 17:20:56 +03:00
Jouni Malinen
0cb79d355a dbus: Fix indentation level to match code logic
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-07-02 13:03:45 +03:00
Jouni Malinen
010fc5f507 dbus: Clean up array-array-type property getter
The previously used design was a bit too complex for static analyzers
(e.g., CID 68131, CID 68133) to understand which resulted in false
warnings about uninitialized memory. Avoid this by explicitly
initializing the pointer array to NULL and also skipping any invalid
NULL entry in the helper function.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-29 18:20:13 +03:00
Tomasz Bursztyka
ea18024d78 dbus: Add PropertiesChanged signal to Peer object
This signal will be thrown when a Peer joins or leaves a group.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-06-29 17:28:14 +03:00
Tomasz Bursztyka
bf035663c9 dbus: Remove GroupMember object type and use Peer instead
GroupMember is unusable in itself and all the necessary informations are
stored in Peer objects, thus replace the use of GroupMember by Peer.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-06-29 17:19:12 +03:00
Tomasz Bursztyka
17a37d7110 dbus: Add a Groups property to a Peer object on which it belongs
If only the Peer is part of one or more group, this property will tell
those via listing their object paths.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-06-29 17:09:32 +03:00
Jouni Malinen
25be28a375 dbus: Check return value more consistently (CID 62841)
Most of these calls are checked to return success and there is no reason
why these wouldn't, so be more consistent. This addresses CID 62841,
CID 62840, CID 62839, CID 62838, CID 62837, CID 62836.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-14 12:32:53 +03:00
Jouni Malinen
1851e17a64 dbus: Clean up P2P group vendor ext getter
The vendor_ext[i] = NULL setting did not make any sense since
num_vendor_ext should have been used to index the vendor_ext array. The
old code did not do any harm since i >= num_vendor_ext and none of the
already set entries could have been cleared. Anyway, better clean this
by making it skip the setting to NULL similarly to what was already done
in the P2P peer vendor ext getter.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:48:21 +03:00
Jouni Malinen
e987c70c85 dbus: Add explicit break statements to switch-default
There were couple of missing breaks in switch-default (before/after).
While these did not have any noticeable issues due to falling over to
the next step that just exited from the switch statement, it is cleaner
and more robust to have each case use an explicit break.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:27:15 +03:00
Jouni Malinen
6446420b24 dbus: Initialize temporary entry properly (CID 62877)
The tmpentry variable was not initialized and
_wpa_dbus_dict_entry_get_byte_array() does not set tmpentry.type, so it
would have been possible for the error path to end up trying to free
unexpected type of an entry or not free the memory at all.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-13 00:27:15 +03:00
Jouni Malinen
beb9e1171e dbus: Avoid theoretical memory leaks with duplicated dict entries
If a dict would include duplicated items, the parsing code here would
have leaked memory by overwriting old os_strdup() result with the new
one. Fix this by explicitly freeing the previous entry. This addresses
CID 62852, CID 62851, CID 62850, CID 62849, CID 62847, CID 62846.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-12 19:45:06 +03:00
Jouni Malinen
ceb4cd89c9 dbus: Fix a potential double-free in on error path (CID 62880)
It would have been at least theoretically possible to hit the first
error in the loop and end up jumping to error handling which would call
os_free(value) without the value having been cleared after the os_free()
call at the end of the previous loop iteration.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-12 19:45:02 +03:00
Nirav Shah
d3b204694a P2P: Make the default p2p_find delay value configurable
This makes the p2p_find default delay value configurable as
p2p_search_delay parameter through the configuration file (and through
control interface "SET p2p_search_delay <value>" on the P2P management
interface.

This parameter controls the number milliseconds of extra delay that is
added between search iterations when there is a concurrent operation in
progress. This can be used, e.g., p2p_search_delay=100 to make p2p_find
friendlier to concurrent operations by avoiding it from taking 100% of
the radio resources. The default value is the previous default, i.e.,
500 ms. Smaller values can be used to find peers more quickly at the
cost of larger effect to concurrent operations while a larger value
leaves more time for the concurrent operations at the cost of making
device discovery take longer time.

The optional p2p_find delay argument can still be used to override the
search delay for each search operation.

Since the P2P_CONCURRENT_SEARCH_DELAY macro is not used anymore, the
driver specific build parameter for bcmdhd from Android.mk is also
removed. Similar configuration can now be achieved with
p2p_search_delay=0 in the p2p0 interface configuration file.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-09 19:43:26 +03:00
Boris Sorochkin
e403ba859e Parse DMG capabilities when reporting to external interfaces
This adds [DMG] and [PBSS] flags for scan results and BSS table entries
using the IEEE Std 802.11ad-2012 updated definition of the Capability
field.

Signed-off-by: Boris Sorochkin <qca_bsoroc@qca.qualcomm.com>
2014-05-26 23:35:52 +03:00
Tomasz Bursztyka
68d270069f dbus: No need to recompute group object path on GroupStarted signal
The group object is already registered on DBus at that point, thus wpa_s
structure holds its path already.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-05-16 18:20:17 +03:00
Tomasz Bursztyka
f3734e2377 dbus: Provide the P2P Device Address from the relevant structure
Fixes a minor mistake: the p2p_info structure should be used here
instead of the peer_handler_args one.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-05-16 18:19:37 +03:00
Tomasz Bursztyka
e956b830fc dbus: Fix interface DeviceFound signal specification
DeviceFound does not provide any properties, just the peer object path.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-05-16 18:19:10 +03:00
Tomasz Bursztyka
fc591a771c dbus: Declare GONegotiation signals properly
These signals delivers an array of key/value pairs, thus declaring those
as it should.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-05-16 18:18:39 +03:00
Alexandru Costache
fb2ac53df1 Remove leftover timeouts on cleanup
Signed-off-by: Alexandru Costache <alexandru.costache.100@gmail.com>
2014-05-12 19:43:59 +03:00
Hannu Mallat
316f92cd33 dbus: Reorder deauthentication and cleanup calls when removing a network
Valgrind indicates reference to already freed memory if function
wpa_config_remove_network() is called prior to calling
wpa_supplicant_deauthenticate(), and this can lead to a crash.
Inverting the call order fixes the problem.

Signed-off-by: Hannu Mallat <hannu.mallat@jollamobile.com>
2014-05-12 18:05:38 +03:00
quiche@chromium.org
e9b32dae1a Propagate scan failures over D-Bus
If we receive a scan request via D-Bus and wpa_supplicant_scan_trigger
fails, return the failure to the caller over D-Bus.

Signed-hostap: mukesh agrawal <quiche@chromium.org>
2014-04-13 23:43:04 +03:00
Fionn Cleary
481e66b1f8 Fix reassociate dbus method
- Reassociate was only working when there was already a connect in
  place, which is not how the REASSOCIATE command from the ctrl
  interface works.

Signed-off-by: Fionn Cleary <fionn.cleary@streamunlimited.com>
2014-04-11 19:22:00 +03:00
Jouni Malinen
dc39004318 WPS: Remove unused WEP related functionality
Now that WPS 2.0 support is enabled unconditionally, WEP and Shared auth
type are not allowed. This made some of the older code unused and that
can now be removed to clean up the implementation. There is still one
place where WEP is allowed for testing purposes: wpa_supplicant as
Registrar trying to configure an AP to use WEP. That is now only allowed
in CONFIG_TESTING_OPTIONS=y builds, though.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-06 12:31:45 +03:00
Tomasz Bursztyka
b998236543 dbus: Implement P2P Peers info IEs buffer getter
Since it declares providing such property, let's expose it relevantly.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-03-21 23:49:47 +02:00
Tomasz Bursztyka
c6f356f85b dbus: Export the peer's device address as a property
This could be useful in some cases.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-03-21 23:44:09 +02:00
Tomasz Bursztyka
442adfde3d dbus: Declare properly ServiceDiscoveryRequest method
It does return something: the reference of the request, as an integer,
which can be used then with ServiceDiscoveryCancelRequest to get
canceled.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-03-21 23:36:50 +02:00
Tomasz Bursztyka
890374118f dbus: Cancelling a service request always reply by an error
p2p_sd_cancel_request returns -1 in case of error, so does
wpas_p2p_sd_cancel_request.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-03-21 23:36:49 +02:00
Tomasz Bursztyka
13494c4478 dbus: Remove duplicate signal declaration
ServiceDiscoveryExternal is uselessly declared twice.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-03-21 23:36:49 +02:00
Guoqiang Liu
d06ecab344 D-Bus: Make p2p_no_group_iface configurable
Some old device need to set p2p_no_group_iface=1 to set up a P2P
connection, so add a D-Bus interface to configure it.

Signed-off-by: Guoqiang Liu <guoqiang.liu@archermind.com>
2014-03-21 22:17:57 +02:00
Peter Qiu
0f44ec8eba Add a reattach command for fast reassociate-back-to-same-BSS
Add "reattach" command to perform single-channel single-ssid scan
instead of full scan when trying to reconnect to the currently
"connected" network (assuming old scan results are not current enough to
skip the scan completely). This allows the scan result to come back in
much faster time. In ath9k, the scan took around 12 seconds with full
background scan, and only 0.1 second with the single-channel single-ssid
scan. Thus, take much less time for the client to re-establish
connection with the currently "connected" network.

Signed-hostap: Peter Qiu <zqiu@chromium.org>
2014-03-11 19:38:01 +02:00
Jouni Malinen
508e24c20b dbus: Clean up error reporting for TDLS peer address parsing
Passing a pointer to an error reply message is not very robust since
memory allocation could fail even for that error message. Instead, use a
separate error value as the return value from get_peer_hwaddr_helper()
and return a pointer to the error message through a pointer-to-pointer
so that the error case will always be clear.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-02 17:15:12 +02:00
Jouni Malinen
a7c37d92d2 dbus: Remove duplicated variable assignment
This gets rid of a static analyzer warning.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-02 17:15:12 +02:00
Mahesh A Saptasagar
062a7c0d67 Fix persistent P2P connection failure in case channel list changes
P2P persistent connection may fail due to 802.11d channel change event
invalidating support of the operating frequency sent in the invitation
request, before receiving the invitation response. If the operating
frequency is invalid at the time the invitation response is processed
and there is no forced frequency provided by user, allow frequency
re-selection.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-07 15:44:41 +02:00
Jouni Malinen
0187c41d88 Declare wpa_debug_* variables in src/utils/wpa_debug.h
These were somewhat more hidden to avoid direct use, but there are now
numerous places where these are needed and more justification to make
the extern int declarations available from wpa_debug.h. In addition,
this avoids some warnings from sparse.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-31 19:29:52 +02:00
Jouni Malinen
30675c3416 Add definitions for new cipher suites from IEEE Std 802.11ac-2013
This adds initial parts for supporting the new GCMP-256, CCMP-256,
BIP-GMAC-128, BIP-GMAC-256, and BIP-CMAC-256 cipher suites.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-24 22:21:04 +02:00
Jouni Malinen
7feff06567 Add CONFIG_CODE_COVERAGE=y option for gcov
This can be used to measure code coverage from test scripts.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-24 19:16:12 +02:00
Michael Schaller
bdec7ee5c9 D-Bus: Add support to set pkcs11_{engine,module}_path
Add SetPKCS11EngineAndModulePath D-Bus method. Add PKCS11EnginePath
and PKCS11ModulePath D-Bus property getters.

Signed-hostap: Michael Schaller <misch@google.com>
2013-11-23 10:48:27 +02:00
Paul Stewart
cea97a04f9 dbus_new: Add DBus TDLS methods
Add DBus methods for TDLS operations similar to those available
for the control interface. This includes Discover, Setup, and
Teardown commands. While here, add a method to query the TDLS
link status and add a DBus method for it.

Tested with CONFIG_TDLS enabled, on a TDLS-enabled host and
peer capable of TDLS:

    dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
        /fi/w1/wpa_supplicant1/Interfaces/0 \
        fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>

    yields: string "peer does not exist"

    dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
        /fi/w1/wpa_supplicant1/Interfaces/0 \
        fi.w1.wpa_supplicant1.Interface.TDLSDiscover string:<peer-mac-address>

    yields no error

    dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
        /fi/w1/wpa_supplicant1/Interfaces/0 \
        fi.w1.wpa_supplicant1.Interface.TDLSSetup string:<peer-mac-address>

    yields no error

    dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
        /fi/w1/wpa_supplicant1/Interfaces/0 \
        fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>

    yields: string "connected" after TDLS completes

    dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
        /fi/w1/wpa_supplicant1/Interfaces/0 \
        fi.w1.wpa_supplicant1.Interface.TDLSTeardown string:<peer-mac-address>

    yields no error

    dbus-send --system --dest=fi.w1.wpa_supplicant1 --print-reply \
        /fi/w1/wpa_supplicant1/Interfaces/0 \
        fi.w1.wpa_supplicant1.Interface.TDLSStatus string:<peer-mac-address>

    yields: string "peer not connected"

Signed-hostap: Paul Stewart <pstew@chromium.org>
2013-11-17 16:47:32 +02:00
Eliad Peller
20ea1ca406 P2P: Add VHT parameter to P2P operations
Add the option to ask for VHT operation similarly to the way ht40 is
configured - either by adding 'vht' param to the relevant p2p_*
commands or by configuring p2p_go_vht=1 in the configuration file.

This patch only adds the configuration option (e.g., via control
interface). The actual handling of the VHT parameter (asking the driver
to use VHT, etc.) will be done by the following patch.

Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
2013-10-27 19:46:17 +02:00
Jouni Malinen
e7ecab4a3b Use ARRAY_SIZE() macro
Replace the common sizeof(a)/sizeof(a[0]) constructions with a more
readable version.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-26 17:49:05 +03:00
Dan Williams
538922a628 dbus: Add boolean AllowRoam option to Scan() method options dictionary
To disallow roaming when a scan request's results are read, callers
of the D-Bus Scan() method may add a new "AllowRoam" boolean key
to the scan options dictionary and set that key's value to FALSE.

Signed-hostap: Dan Williams <dcbw@redhat.com>
2013-10-22 16:09:46 +03:00
Jouni Malinen
0c92963656 D-Bus: Clean up debug print for P2P invitation result
wpa_printf() does not need '\n' so remove the extra newline. In
addition, drop the priority of this message from MSG_INFO to MSG_DEBUG
since this is in no way exceptional operation.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-20 21:38:02 +03:00
Jouni Malinen
bbc6c729a5 P2P: Use group formation timeout on persistent group GO
Previously, GO considered the group to be fully re-invoked after
starting beaconing on successful invitation exchange. This would leave
the group running until idle timeout (which may not be enabled) or
explicit removal if the client fails to connect for any reason. Since
the client is expected to connect immediately after the invitation
exchange that ends with status=0 (i.e., either client initiated the
exchange or it responded with success), extend group formation timeout
to cover that period until the first successfully completed data
connection. This allows the GO to remove the group automatically if the
client devices does not connect within
P2P_MAX_INITIAL_CONN_WAIT_GO_REINVOKE (15) seconds.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-09-26 21:24:09 +03:00
Jouni Malinen
731ef436d1 D-Bus: Fix per-iface object unregistration on not existing objects
If the private data for an object is not found, do not try to unregister
that object to avoid D-Bus errors.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-08-31 16:46:24 +03:00
Tomasz Bursztyka
06aeff5f8f dbus: Register the AutoScan method call at the right place
Signed-hostap: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2013-07-01 19:11:34 +03:00
Chengyi Zhao
8a901d750b D-Bus: Emit signal when a station is authorized or deauthorized
Add "StaAuthorized" and "StaDeauthorized" D-Bus interface in AP mode.
After enabling the AP mode of wpa_supplicant, the other process need to
get the MAC address and authorization status of every station, so
wpa_supplicant emits signal when the station is authorized or
deauthorized.

Signed-hostap: Chengyi Zhao <chengyix.zhao@gmail.com>
2013-06-22 12:09:09 +03:00
Daniel Gnoutcheff
d7692b8d1c dbus: Terminate cleanly on messagebus shutdown
By default, dbus_connection_dispatch() will call _exit() if the bus
connection has been closed. This caused wpa_supplicant to terminate
without properly cleaning up after itself.

To ensure that we terminate cleanly when the messagebus terminates,
override the exit_on_disconnect behavior and install a filter to handle
libdbus's "Disconnected" signal.

[Bug 474]

Signed-hostap: Daniel Gnoutcheff <daniel@gnoutcheff.name>
2013-05-16 20:47:28 +03:00
Paul Stewart
754632c965 dbus_new: Add EAP logon/logoff
Add "EAPLogoff" and "EAPLogon" interface DBus commands which
parallel the "logoff" and "logon" wpa_ctrl commands which terminate
and restart EAP authentication.  Slightly enhance the "logon" case
by expiring any running "startWhile" timer.

Signed-hostap: Paul Stewart <pstew@chromium.org>
2013-04-23 17:57:55 +03:00