Commit graph

253 commits

Author SHA1 Message Date
Jouni Malinen
2a58968d39 SAE-PK: Allow SAE-PK password to be set using the psk parameter
Only the sae_password parameter was previously accepted for SAE-PK use.
That is not sufficient for covering mixed SAE+PSK cases. Extend this by
allowing the psk parameter to be used as well just like it can be used
for SAE without SAE-PK.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-08-07 00:49:00 +03:00
Jouni Malinen
9ad010c290 SAE-PK: Allow automatic SAE-PK to be disabled
This replaces the previously used sae_pk_only configuration parameter
with a more generic sae_pk that can be used to specify how SAE-PK is
negotiated. The default behavior (sae_pk=0) is to automatically
negotiate SAE-PK whenever the AP supports it and the password is in
appropriate format. sae_pk=1 allows only SAE-PK to be used and sae_pk=2
disables SAE-PK completely.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-07 11:55:16 +03:00
Jouni Malinen
cc22fb1b86 SAE: Move H2E and PK flags to main sae_data
This maintains knowledge of whether H2E or PK was used as part of the
SAE authentication beyond the removal of temporary state needed during
that authentication. This makes it easier to use information about which
kind of SAE authentication was used at higher layer functionality.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-06 15:18:13 +03:00
Jouni Malinen
1c846d647e SAE-PK: Allow SAE authentication without PK to be disabled
The new wpa_supplicant network profile parameter sae_pk_only=1 can now
be used to disable use of SAE authentication without SAE-PK.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-06 15:18:13 +03:00
Jouni Malinen
e7aeb6d8ac SAE-PK: STA functionality
This adds STA side functionality for SAE-PK. This version enables SAE-PK
automatically based on the configured SAE password value if the selected
AP advertises support for SAE-PK.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-02 23:25:22 +03:00
Jouni Malinen
6b9e99e571 SAE-PK: Extend SAE functionality for AP validation
This adds core SAE functionality for a new mode of using SAE with a
specially constructed password that contains a fingerprint for an AP
public key and that public key being used to validate an additional
signature in SAE confirm from the AP.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-02 23:25:22 +03:00
Jouni Malinen
8c1f61e820 OCV: Report OCI validation failures with OCV-FAILURE messages (STA)
Convert the previously used text log entries to use the more formal
OCV-FAILURE prefix and always send these as control interface events to
allow upper layers to get information about unexpected operating channel
mismatches.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-30 00:24:15 +03:00
Jouni Malinen
52579be860 OCV: Move "OCV failed" prefix to callers
Make reporting of OCV validation failure reasons more flexible by
removing the fixed prefix from ocv_verify_tx_params() output in
ocv_errorstr so that the caller can use whatever prefix or encapsulation
that is most appropriate for each case.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-25 18:34:59 +03:00
Vamsi Krishna
2d118f557a OCV: Add support to override channel info OCI element (STA)
To support the STA testbed role, the STA has to use specified channel
information in OCI element sent to the AP in EAPOL-Key msg 2/4, SA Query
Request, and SA Query Response frames. Add override parameters to use
the specified channel while populating OCI element in all these frames.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-25 18:01:44 +03:00
Jouni Malinen
12c8eacf73 DPP: Allow version number to be overridden for testing purposes
"SET dpp_version_override <ver>" can now be used to request
wpa_supplicant and hostapd to support a subset of DPP versions. In
practice, the only valid case for now is to fall back from DPP version 2
support to version 1 in builds that include CONFIG_DPP2=y.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-04 00:37:45 +03:00
Jouni Malinen
1f5f000086 DPP2: Try to negotiate PFS only if AP supports version 2 or newer
Check AP's DPP Protocol Version during network introduction and mark the
PMKSA cache as suitable for PFS use with version 2 or newer. This avoids
unnecessary attempt of negotiating PFS with version 1 APs.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-04 00:37:44 +03:00
Jouni Malinen
f6c22dcdea Use a local pointer to simply current_ssid accesses in sme_associate()
It is simpler to assign wpa_s->current_ssid to a local pointer now that
there are numerous dereferences of current_ssid within sme_associate().

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-04 00:37:44 +03:00
Jouni Malinen
da8478a1ab EAPOL supp: Convert Boolean to C99 bool
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-24 17:06:50 +03:00
P Praneesh
7c8f540ee0 wpa_supplicant: Add HE override support
Add HE override support under the build parameter CONFIG_HE_OVERRIDES=y.
The disable_he=1 network profile parameter can be used to disable HE.
This requires a fallback to VHT on the 5 GHz band and to HT on the 2.4
GHz band.

There is no nl80211 support for configuring the driver to disable HE, so
for now, this applies only to IBSS and mesh cases.

Signed-off-by: P Praneesh <ppranees@codeaurora.org>
2020-03-30 12:55:01 +03:00
Jouni Malinen
5058f771d9 DPP2: Allow station to require or not allow PFS
The new wpa_supplicant network profile parameter dpp_pfs can be used to
specify how PFS is applied to associations. The default behavior
(dpp_pfs=0) remains same as it was previously, i.e., try to use PFS if
the AP supports it. PFS use can now be required (dpp_pfs=1) or disabled
(dpp_pfs=2).

This is also working around an interoperability issue of DPP R2 STA with
certain hostapd builds that included both OWE and DPP functionality.
That issue was introduced by commit 09368515d1 ("OWE: Process
Diffie-Hellman Parameter element in AP mode") and removed by commit
16a4e931f0 ("OWE: Allow Diffie-Hellman Parameter element to be
included with DPP"). hostapd builds between those two commits would
reject DPP association attempt with PFS. The new wpa_supplicant default
(dpp_pfs=0) behavior is to automatically try to connect again with PFS
disabled if that happens.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-28 17:23:22 +02:00
Jouni Malinen
eb26a6997d Allow SA Query to be disabled for testing purposes
The new wpa_supplicant control interface SET parameter disable_sa_query
can now be used to disable SA Query on receiving unprotected
disconnection event.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-21 18:12:02 +02:00
Jouni Malinen
6140cca819 FT: Omit RSNXE from FT protocol Reassociation Request when needed
The previous design for adding RSNXE into FT was not backwards
compatible. Move to a new design based on 20/332r3 to avoid that issue
by not include RSNXE in the FT protocol Reassociation Request frame so
that an AP not supporting RSNXE can still validate the FTE MIC
correctly.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-21 00:01:47 +02:00
Ananya Barat
2b9713d616 Fill the current opclass in (Re)AssocRequest depending on HT/VHT IEs
The previous implementation was assuming a fixed 20 MHz channel
bandwidth when determining which operating class value to indicate as
the Current Operating Class in the Supported Operating Classes element.
This is not accurate for many HT/VHT cases.

Fix this by determining the current operating class (i.e., the operating
class used for the requested association) based on the HT/VHT operation
elements from scan results.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-11 18:30:31 +02:00
Jouni Malinen
10223b501b SAE: Expose sae_write_commit() error cases to callers
Check whether an error is reported from any of the functions that could
in theory fail and if so, do not proceed with the partially filled SAE
commit buffer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-08 16:59:42 +02:00
Ilan Peer
c4988e73c0 driver: Extend send_mlme() with wait option
PASN authentication can be performed while a station interface is
connected to an AP. To allow sending PASN frames while connected, extend
the send_mlme() driver callback to also allow a wait option. Update the
relevant drivers and wpa_supplicant accordingly.

hostapd calls for send_mlme() are left unchanged, since the wait option
is not required there.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2020-02-29 23:03:20 +02:00
Jouni Malinen
200c7693c9 Make WEP functionality an optional build parameter
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-29 17:45:25 +02:00
Jouni Malinen
641d79f165 SAE: Special test mode sae_pwe=3 for looping with password identifier
The new sae_pwe=3 mode can be used to test non-compliant behavior with
SAE Password Identifiers. This can be used to force use of
hunting-and-pecking loop for PWE derivation when Password Identifier is
used. This is not allowed by the standard and as such, this
functionality is aimed at compliance testing.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-02-10 05:13:13 +02:00
Jouni Malinen
ca1cecc54d SAE: Verify that appropriate Status Code is used in SAE commit (SME)
Previous version accepted both 0 and 126 values in SAE commit message
from the AP. Explicitly check that the value the AP uses matches what
the STA started with to avoid unexpected cases.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-02-08 07:19:53 +02:00
Vamsi Krishna
d0e116f61f Enhance get_mode() to return correct hw_mode with 6 GHz support
The 5 GHz channels are stored in one hw_features set with mode
HOSTAPD_MODE_IEEE80211A while the 6 GHz channels will need to be stored
in a separate hw_features set (but with same mode
HOSTAPD_MODE_IEEE80211A) due to possibility of different HT/VHT/HE
capabilities being available between the 5 GHz and 6 GHz bands.

Iterate through all hw_features sets and check and match the band of
channel supported by the hw_features set while getting the hw_features
set in get_mode(). This allows both the 5 GHz and 6 GHz channels to be
found and correct capabilities to be used in cases where the driver
reports different capability values between 5 and 6 GHz channels.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-23 15:48:51 +02:00
Jouni Malinen
5e32fb0170 SAE: Use Anti-Clogging Token Container element with H2E
IEEE P802.11-REVmd was modified to use a container IE for anti-clogging
token whenver H2E is used so that parsing of the SAE Authentication
frames can be simplified.

See this document for more details of the approved changes:
https://mentor.ieee.org/802.11/dcn/19/11-19-2154-02-000m-sae-anti-clogging-token.docx

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-21 13:13:56 +02:00
Jouni Malinen
e36a5894d0 SAE: Use H2E whenever Password Identifier is used
IEEE P802.11-REVmd was modified to require H2E to be used whenever
Password Identifier is used with SAE.

See this document for more details of the approved changes:
https://mentor.ieee.org/802.11/dcn/19/11-19-2154-02-000m-sae-anti-clogging-token.docx

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-21 13:13:56 +02:00
Jouni Malinen
af670cb418 SME: Postpone current BSSID clearing until IEs are prepared
sme_send_authentication() could fail before actually requesting the
driver to authenticate with a new AP. This could happen after
wpa_s->bssid got cleared even though in such a case, the old association
is maintained and still valid. This can result in unexpected behavior
since wpa_s->bssid would not match the current BSSID anymore.

Fix this by postponing clearing of wpa_s->bssid until the IE preparation
has been completed successfully.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-03 18:06:01 +02:00
Sergey Matyukevich
3204795d7a STA OBSS: Add check for overlapping BSSs
In the previous implementation connected STA performs OBSS scan
according to requests from its 20/40 MHz AP. However STA checks only 40
MHz intolerance subfield from HT Capabilities element in scan results.
Meanwhile, as per IEEE Std 802.11-2016, 11.16.12, STA should check
overlapping BSSs as well.

Note that all the required code to check overlapping BSSs did already
exist for AP mode since AP does those checks properly before operating
as 20/40 MHz BSS in the 2.4 GHz band. Use that existing code by replace
existing 40 MHz intolerance check in sme_proc_obss_scan() with the new
shared helper function check_bss_coex_40mhz().

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
2019-12-26 11:41:01 +02:00
Jouni Malinen
1325655397 SAE H2E: RSNXE override for testing purposes
"SET rsnxe_override_{assoc,eapol} <hexdump>" can now be used to override
RSNXE in (Re)Association Request frames and EAPOL-Key msg 2/4 for
testing purposes.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-07 12:54:54 +02:00
Jouni Malinen
c88e01e1b6 SAE H2E: Fix validation of rejected groups list
check_sae_rejected_groups() returns 1, not -1, in case an enabled group
is rejected. The previous check for < 0 could not have ever triggered.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-07 00:28:13 +02:00
Jouni Malinen
1b5865a53f SAE: Ignore commit message when waiting for confirm in STA mode
Previously, an unexpected SAE commit message resulted in forcing
disconnection. While that allowed recovery by starting from scratch,
this is not really necessary. Ignore such unexpected SAE commit message
instead and allow SAE confirm message to be processed after this. This
is somewhat more robust way of handling the cases where SAE commit
message might be retransmitted either in STA->AP or AP->STA direction.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-10-27 14:35:04 +02:00
Jouni Malinen
6d6c887751 SAE: Add RSNXE in Association Request and EAPOL-Key msg 2/4
Add the new RSNXE into (Re)Association Request frames and EAPOL-Key msg
2/4 when using SAE with hash-to-element mechanism enabled. This allows
the AP to verify that there was no downgrade attack when both PWE
derivation mechanisms are enabled.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-17 16:54:05 +03:00
Jouni Malinen
444d76f74f SAE: Check that peer's rejected groups are not enabled
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-15 15:39:22 +03:00
Jouni Malinen
cfe1ea5c9c SAE: H2E version of SAE commit message handling for STA
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-15 15:39:22 +03:00
Jouni Malinen
447cd5f2df SAE: Collect list of rejected groups for H2E in STA
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-15 15:39:22 +03:00
Jouni Malinen
86f6084862 SAE: Tell sae_parse_commit() whether H2E is used
This will be needed to help parsing the received SAE commit.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-14 19:38:41 +03:00
Vamsi Krishna
2e06cef80a MBO/OCE: Work around misbehaving MBO/OCE APs that use RSN without PMF
The MBO and OCE specification require the station to mandate use of PMF
when connecting to an MBO/OCE AP that uses WPA2. The earlier
implementation prevented such misbehaving APs from being selected for
connection completely. This looks like the safest approach to take, but
unfortunately, there are deployed APs that are not compliant with the
MBO/OCE requirements and this strict interpretation of the station
requirements results in interoperability issues by preventing the
association completely.

Relax the approach by allowing noncompliant MBO/OCE APs to be selected
for RSN connection without PMF to avoid the main impact of this
interoperability issue. However, disable MBO/OCE functionality when PMF
cannot be negotiated to try to be as compliant as practical with the
MBO/OCE tech spec requirements (i.e., stop being an MBO/OCE STA for the
duration of such workaround association). Also disable support for BTM
in this workaround state since MBO would expect all BTM frames to be
protected.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-09-21 00:58:33 +03:00
Jouni Malinen
7d2ed8bae8 Remove CONFIG_IEEE80211W build parameter
Hardcode this to be defined and remove the separate build options for
PMF since this functionality is needed with large number of newer
protocol extensions and is also something that should be enabled in all
WPA2/WPA3 networks.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-09-08 17:33:40 +03:00
Sunil Dutt
346d10cf82 SAE: Conditionally set PMKID while notifying the external auth status
This is needed for the drivers implementing SME to include the PMKID in
the Association Request frame directly following SAE authentication.

This commit extends the commit d2b2083843 ("SAE: Allow PMKID to be
added into Association Request frame following SAE") for drivers with
internal SME that use the external authentication mechanism.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-08-16 15:37:36 +03:00
Sunil Dutt
b7cd64876d SAE: Use BSSID stored in ext_auth_bssid for set_pmk
pending_bssid is cleared in the connected state and thus is not valid if
SAE authentication is done to a new BSSID when in the connected state.
Hence use the BSSID from ext_auth_bssid while configuring the PMK for
the external authentication case. This is required for roaming to a new
BSSID with driver-based-SME while the SAE processing happens with
wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-08-16 15:32:55 +03:00
Jouni Malinen
d2b2083843 SAE: Allow PMKID to be added into Association Request frame following SAE
IEEE Std 802.11-2016 does not require this behavior from a SAE STA, but
it is not disallowed either, so it is useful to have an option to
identify the derived PMKSA in the immediately following Association
Request frames. This is disabled by default (i.e., no change to previous
behavior) and can be enabled with a global wpa_supplicant configuration
parameter sae_pmkid_in_assoc=1.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-08-14 17:49:23 +03:00
Sven Eckelmann
f74618cb92 wpa_supplicant: Fix type for ssid->mode comparisons
The ssid->mode is from type enum wpas_mode and all its constants start
with WPAS_MODE_*. Still some of the code sections used the
IEEE80211_MODE_* defines instead of WPAS_MODE_*.

This should have no impact on the actual code because the constants for
INFRA, IBSS, AP and MESH had the same values.

Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
2019-06-23 18:03:51 +03:00
Srinivas Dasari
fb6ebd1ced SAE: Send external auth failure status to driver
wpa_supplicant prepares auth commit request as part of the external
authentication (first SAE authentication frame), but it fails to get
prepared when wpa_supplicant is started without mentioning the SAE
password in configuration. Send this failure status to the driver to
make it aware that the external authentication has been aborted by
wpa_supplicant.

Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
2019-05-31 16:52:15 +03:00
Jouni Malinen
d42df8d6ce Fix a regression in storing of external_auth SSID/BSSID
An earlier change in drivers_ops API for struct external_auth broke the
way SSID and BSSID for an external authentication request were stored.
The implementation depended on the memory array being available in the
API struct with a use of memcpy() to copy the full structure even though
when only SSID and BSSID was needed. Fix this by replacing that
easy-to-break storing mechanism with explicit arrays for the exact set
of needed information.

Fixes: dd1a8cef4c ("Remove unnecessary copying of SSID and BSSID for external_auth")
Signed-off-by: Jouni Malinen <j@w1.fi>
2019-04-28 16:24:32 +03:00
Andrei Otcheretianski
31cf52bf2e Do not clear FT IEs twice in sme_deinit()
Remove FT IEs clearing from sme_deinit() as it is done twice. The
sme_clear_on_disassoc() call to sme_update_ft_ies() takes care of this.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2019-04-16 00:48:27 +03:00
Andrei Otcheretianski
01ac337b32 Stop SA Query on disconnection
SA Query wasn't stopped after disconnection, which could potentially
result in an unexpected SA timeout firing later when already connected
to another AP. Fix that by stopping SA Query when an association is
terminated.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2019-04-16 00:48:27 +03:00
Jouni Malinen
7a206c504f Add debug print on stopping SA Query procedure
This makes it easier to debug SA Query behavior.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-04-16 00:42:58 +03:00
Jouni Malinen
dd1a8cef4c Remove unnecessary copying of SSID and BSSID for external_auth
The external authentication command and event does not need to copy the
BSSID/SSID values into struct external_auth since those values are used
before returning from the call. Simplify this by using const u8 * to
external data instead of the array with a copy of the external data.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-04-12 20:43:26 +03:00
Jouni Malinen
be609c6fc6 SAE: Fix commit message override with external authentication
Do not add duplicate Transaction Sequence and Status Code fields when
using test functionality to override SAE commit message.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-04-01 13:28:26 +03:00
Jouni Malinen
ab3aebcce5 SAE: Fix PMKSA cache entry search for FT-SAE case
Previously, PMKSA cache entries were search for AKM=SAE and that did not
find an entry that was created with FT-SAE when trying to use FT-SAE
again. That resulted in having to use full SAE authentication instead of
the faster PMKSA caching alternative.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-03-27 04:03:12 +02:00