Commit graph

456 commits

Author SHA1 Message Date
Jouni Malinen
466e48dcd7 HT: Remove SMPS in AP mode
SM Power Save was described in somewhat unclear manner in IEEE Std
802.11n-2009 as far the use of it locally in an AP to save power. That
was clarified in IEEE Std 802.11-2016 to allow only a non-AP STA to use
SMPS while the AP is required to support an associated STA doing so. The
AP itself cannot use SMPS locally and the HT Capability advertisement
for this is not appropriate.

Remove the parts of SMPS support that involve the AP using it locally.
In practice, this reverts the following commits:
04ee647d58 ("HT: Let the driver advertise its supported SMPS modes for AP mode")
8f461b50cf ("HT: Pass the smps_mode in AP parameters")
da1080d721 ("nl80211: Advertise and configure SMPS modes")

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-16 13:58:54 +02:00
Vamsi Krishna
d0e116f61f Enhance get_mode() to return correct hw_mode with 6 GHz support
The 5 GHz channels are stored in one hw_features set with mode
HOSTAPD_MODE_IEEE80211A while the 6 GHz channels will need to be stored
in a separate hw_features set (but with same mode
HOSTAPD_MODE_IEEE80211A) due to possibility of different HT/VHT/HE
capabilities being available between the 5 GHz and 6 GHz bands.

Iterate through all hw_features sets and check and match the band of
channel supported by the hw_features set while getting the hw_features
set in get_mode(). This allows both the 5 GHz and 6 GHz channels to be
found and correct capabilities to be used in cases where the driver
reports different capability values between 5 and 6 GHz channels.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-23 15:48:51 +02:00
Jouni Malinen
b7bb2c0204 P2P: Move p2p_long_listen into struct wpa_global
This variable is not specific to any P2P group interface and since it
was already used through global->p2p_init_wpa_s, it is cleaner to simply
move this to the global structure so that there is a single variable
instead of per-interface variables and need to pick the correct
interface.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-04 23:11:28 +02:00
Jouni Malinen
6c57019376 Test functionality to override driver reported signal levels
"SET driver_signal_override <BSSID> [<si_signal< <si_avg_signal>
<si_avg_beacon_signal> <si_noise> <scan_level>]" command can now be used
to request wpa_supplicant to override driver reported signal levels for
signal_poll and scan results. This can be used to test roaming behavior.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-02 20:34:39 +02:00
Jouni Malinen
ad2f096609 Maintain BSS entries for 5 seconds after interface is disabled
This is targeting the case of MAC address change for an association
which may require the interface to be set down for a short moment.
Previously, this ended up flushing the BSS table that wpa_supplicant
maintained and that resulted in having to scan again if the MAC address
was changed between the previous scan and the connection attempt. This
is unnecessary extra latency, so maintain the BSS entries for 5 seconds
(i.e., the same time that the old scan results are consider valid for a
new connection attempt) after an interface goes down.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-02 12:58:58 +02:00
Ahmad Masri
996662250d P2P: Add support for EDMG channels
This allows a P2P connection over P802.11ay EDMG channels to achieve the
highest link speed that the standard allows for channel bonding (CB) up
to CB4.

Let each P2P peer add its EDMG channels to the Supported Channels IE
advertised in P2P GO negotiation. Give EDMG channels priority when peers
negotiate for operating channel.

User may add 'edmg' parameter to p2p_connect, p2p_add_group, and
p2p_invite commands to prefer an EDMG channel for the P2P link. User may
also set p2p_go_edmg=1 in wpa_supplicant configuration file to prefer
EDMG.

When EDMG is used, P2P will try to find the highest channel bonding
supported channel that matches the frequency parameter, if the devices
do not support EDMG, the P2P connection will use a legacy (1-6) 60 GHz
channel.

Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
2019-12-20 00:13:08 +02:00
Jouni Malinen
7404574458 DPP: Replace ap boolean with netRole enum in Configurator params
The netRole enum is more generic and can be extended to include new
roles (e.g., Configurator) more easily.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-12 02:33:00 +02:00
Jouni Malinen
1325655397 SAE H2E: RSNXE override for testing purposes
"SET rsnxe_override_{assoc,eapol} <hexdump>" can now be used to override
RSNXE in (Re)Association Request frames and EAPOL-Key msg 2/4 for
testing purposes.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-07 12:54:54 +02:00
Jouni Malinen
b834e97003 SAE H2E: Testing option to report extra rejected groups
"SET extra_sae_rejected_groups <groups>" can now be used to enable test
mode in which wpa_supplicant will report additional groups (configured
as space separated integers) when using SAE H2E.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-07 00:26:13 +02:00
Jouni Malinen
405946d76a SAE: Testing option to ignore H2E requirement mismatch
"SET ignore_sae_h2e_only 1" can now be used to configurate
wpa_supplicant to a test mode where it ignores AP's H2E-required
advertisement and try to connect with hunt-and-pecking loop instead.
This is used only for testing AP behavior with unexpected STA behavior.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-06 17:13:59 +02:00
Jouni Malinen
6d6c887751 SAE: Add RSNXE in Association Request and EAPOL-Key msg 2/4
Add the new RSNXE into (Re)Association Request frames and EAPOL-Key msg
2/4 when using SAE with hash-to-element mechanism enabled. This allows
the AP to verify that there was no downgrade attack when both PWE
derivation mechanisms are enabled.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-17 16:54:05 +03:00
Jouni Malinen
89450024a8 wpa_supplicant: Pass in operating class for channel validity checks
This is needed to allow the 6 GHz operating classes to be compared
against the driver support channels since the channel numbers are not
really unique identifiers of a channel even within a single band.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-15 15:39:22 +03:00
Jouni Malinen
447cd5f2df SAE: Collect list of rejected groups for H2E in STA
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-15 15:39:22 +03:00
Vamsi Krishna
2e06cef80a MBO/OCE: Work around misbehaving MBO/OCE APs that use RSN without PMF
The MBO and OCE specification require the station to mandate use of PMF
when connecting to an MBO/OCE AP that uses WPA2. The earlier
implementation prevented such misbehaving APs from being selected for
connection completely. This looks like the safest approach to take, but
unfortunately, there are deployed APs that are not compliant with the
MBO/OCE requirements and this strict interpretation of the station
requirements results in interoperability issues by preventing the
association completely.

Relax the approach by allowing noncompliant MBO/OCE APs to be selected
for RSN connection without PMF to avoid the main impact of this
interoperability issue. However, disable MBO/OCE functionality when PMF
cannot be negotiated to try to be as compliant as practical with the
MBO/OCE tech spec requirements (i.e., stop being an MBO/OCE STA for the
duration of such workaround association). Also disable support for BTM
in this workaround state since MBO would expect all BTM frames to be
protected.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-09-21 00:58:33 +03:00
Jouni Malinen
8f8c423a51 DPP: Add bandSupport JSON array into config request
Indicate supported global operating classes when wpa_supplicant is
operating as an Enrollee.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-09-19 00:21:47 +03:00
Jouni Malinen
16ef233bf1 DPP2: Connection status result (Enrollee)
Add support for reporting connection status after provisioning if the
Configurator requests this.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-09-16 17:25:34 +03:00
Jouni Malinen
b0b25c5bbc Clear external eapSuccess setting in driver-authorized cases
The conditions for the eapol_sm_notify_eap_success(FALSE) calls did not
cover the case where eapol_sm_notify_eap_success(TRUE) had been called
based on offloaded 4-way handshake and driver notification of
authorization in wpa_supplicant_event_port_authorized(). This could
result in eapSuccess and altSuccess state machine variables being left
TRUE when roaming to another BSS and that results in EAP failure if the
following roaming case does not get fully authorized through the driver
offload.

Fix this by clearing eapSuccess/altSuccess when processing a new
association (including roaming) event and also when disconnecting from
the network.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-08-07 19:24:06 +03:00
Eric Caruso
91b6eba773 Move MAC address randomization enable/disable to helper functions
This makes it easier to share this for D-Bus implementation.

Signed-off-by: Eric Caruso <ejcaruso@chromium.org>
2019-06-26 20:56:01 +03:00
Sven Eckelmann
3459c54ac7 mesh: Add support for HE mode
Mesh points can partially support HE features (when requiring no
controlling STA/AP) as long as hardware supports it. The kernel just
requires support for HE mesh and wpa_supplicant can forward the peer
capabilities to the kernel for further processing.

Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
2019-06-23 18:03:51 +03:00
Jouni Malinen
d42df8d6ce Fix a regression in storing of external_auth SSID/BSSID
An earlier change in drivers_ops API for struct external_auth broke the
way SSID and BSSID for an external authentication request were stored.
The implementation depended on the memory array being available in the
API struct with a use of memcpy() to copy the full structure even though
when only SSID and BSSID was needed. Fix this by replacing that
easy-to-break storing mechanism with explicit arrays for the exact set
of needed information.

Fixes: dd1a8cef4c ("Remove unnecessary copying of SSID and BSSID for external_auth")
Signed-off-by: Jouni Malinen <j@w1.fi>
2019-04-28 16:24:32 +03:00
Jouni Malinen
4be17ffbd9 Replace int status/reason_code with u16 variable
These cases are for the IEEE 802.11 Status Code and Reason Code and
those fields are unsigned 16 bit values, so use the more appropriate
type consistently. This is mainly to document the uses and to make the
source code easier to understand.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-04-22 22:08:07 +03:00
Ankita Bajaj
822c756e8c MBO: Update connect params with new MBO attributes to driver
MBO attributes Non-preferred channel list and Cellular capabilities are
updated using WNM-Notification Request frame to the current connected
BSS. These same attributes need to be added in the (Re)Association
Request frame sent by the station when roaming, including the case where
the driver/firmware takes care of SME/MLME operations during roaming, so
we need to update the MBO IE to the driver.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-04-05 20:56:03 +03:00
Jouni Malinen
87d8435cf9 DPP: Common configurator/bootstrapping data management
Merge the practically copy-pasted implementations in wpa_supplicant and
hostapd into a single shared implementation in dpp.c for managing
configurator and boostrapping information. This avoid unnecessary code
duplication and provides a convenient location for adding new global DPP
data.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-03-24 17:29:45 +02:00
Jouni Malinen
10ec6a5f38 DPP2: PFS for PTK derivation
Use Diffie-Hellman key exchange to derivate additional material for
PMK-to-PTK derivation to get PFS. The Diffie-Hellman Parameter element
(defined in OWE RFC 8110) is used in association frames to exchange the
DH public keys. For backwards compatibility, ignore missing
request/response DH parameter and fall back to no PFS in such cases.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-03-18 18:32:31 +02:00
Lubomir Rintel
6a8dee76d4 wpa_supplicant: Drop the old D-Bus interface support
This drops support for the fi.epitest.hostap.WPASupplicant D-Bus name
along with the associated CONFIG_CTRL_IFACE_DBUS option. Nothing should
really be using this since 2010.

This is a just a straightforward removal. Perhaps the dbus_common.c and
dbus_new.c can be merged now. Also, the "_NEW" suffix of the config
option seems to make even less sense than it used to.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
2019-03-09 18:33:26 +02:00
Jouni Malinen
3f8ceff54c Indicate wifi_generation in wpa_supplicant STATUS output
This adds a wifi_generation=4/5/6 line to the STATUS output if the
driver reports (Re)Association Request frame and (Re)Association
Response frame information elements in the association or connection
event. Only the generations 4 (HT = 802.11n), 5 (VHT = 802.11ac), and 6
(HE = 802.11ax) are reported.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-02-15 02:09:41 +02:00
Peng Xu
5a3319ab1b P2P: Add 802.11ax support for P2P GO
An optional parameter "he" is added to p2p_connect, p2p_group_add, and
p2p_invite to enable 11ax HE support. The new p2p_go_he=1 configuration
parameter can be used to request this to be enabled by default.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-01-12 13:09:39 +02:00
Ben Greear
cb828507f5 Use disable_ht/vht to constrain supported operating class information
If user has disabled HT or VHT, those related operating classes
should not be advertised as supported.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2019-01-08 00:19:07 +02:00
Peter Oh
0daa7b75fa mesh: Factor out mesh join function
Mesh join function consists of two parts which are preparing
configurations and sending join event to the driver. Since physical mesh
join event could happen either right after mesh configuration is done or
after CAC is done in case of DFS channel is used, factor out the
function into two parts to reduce redundant calls.

Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
2019-01-03 12:35:56 +02:00
Alex Khouderchah
38b405c8f0 dbus: Expose authentication status to D-Bus
wpa_supplicant currently logs CTRL-EVENT-AUTH-FAILED errors when
authentication fails, but doesn't expose any property to the D-Bus
interface related to this.

This change adds the "AuthStatusCode" property to the interface, which
contains the IEEE 802.11 status code of the last authentication.

Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
2019-01-03 00:39:12 +02:00
Matthew Wang
80d06d0ca9 dbus: Export BSS Transition Management status
Add new Interface properties "BSSTMStatus", which carries the status of
the most recent BSS Transition Management request. This property will be
logged in UMA to measure 802.11v success.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2019-01-03 00:27:01 +02:00
Matthew Wang
2bbad1c7c9 dbus: Export roam time, roam complete, and session length
Add new Interface properties "RoamTime", "RoamComplete", and
"SessionLength". "RoamTime" carries the roam time of the most recent
roam in milliseconds. "RoamComplete" carries True or False corresponding
to the success status of the most recent roam. "SessionLength" carries
the number of milliseconds corresponding to how long the connection to
the last AP was before a roam or disconnect happened.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2019-01-03 00:20:34 +02:00
Avraham Stern
ecef0687dc RRM: Support for Last Beacon Report Indication subelement
IEEE P802.11-REVmd/D2.0, 9.4.2.20.7 (Beacon request) and 9.4.2.21.7
(Beacon report) add the Last Beacon Report Indication subelement to
Beacon Request and Beacon Report elements.

Add the Last Beacon Report Indication subelement to all Beacon Report
elements if the Beacon Request indicated that this subelement is
requested.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2019-01-02 16:26:11 +02:00
Beni Lev
19677b77c3 OCE: Add RSSI based association rejection support (STA)
An AP might refuse to connect a STA if it has a low RSSI. In such case,
the AP informs the STA with the desired RSSI delta and a retry timeout.
Any subsequent association attempt with that AP (BSS) should be avoided,
unless the RSSI level improved by the desired delta or the timeout has
expired.

Defined in Wi-Fi Alliance Optimized Connectivity Experience technical
specification v1.0, section 3.14 (RSSI-based association rejection
information).

Signed-off-by: Beni Lev <beni.lev@intel.com>
2019-01-01 17:56:25 +02:00
Jouni Malinen
32bb47faa1 Update wpa_supplicant channel list on FLUSH
Try to make sure the driver channel list state is synchronized with
wpa_supplicant whenever explicitly clearing state (e.g., between hwsim
test cases).

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-01-01 15:58:46 +02:00
Jouni Malinen
2a93ecc8ca Expose Multi-BSS STA capability through wpa_supplicant control interface
Indicate whether the driver advertises support for Multi-BSS STA
functionality with "GET_CAPABILITY multibss" (returns "MULTIBSS-STA" if
supported).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-12-20 21:30:43 +02:00
Venkateswara Naralasetty
5abc7823bd wpa_supplicant: Add Multi-AP backhaul STA support
Advertise vendor specific Multi-AP IE in (Re)Association Request frames
and process Multi-AP IE from (Re)Association Response frames if the user
enables Multi-AP fuctionality. If the (Re)Association Response frame
does not contain the Multi-AP IE, disassociate.

This adds a new configuration parameter 'multi_ap_backhaul_sta' to
enable/disable Multi-AP functionality.

Enable 4-address mode after association (if the Association Response
frame contains the Multi-AP IE). Also enable the bridge in that case.
This is necessary because wpa_supplicant only enables the bridge in
wpa_drv_if_add(), which only gets called when an interface is added
through the control interface, not when it is configured from the
command line.

Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
2018-12-20 12:10:31 +02:00
Jouni Malinen
d514b50265 WNM: Collocated Interference Reporting
Add support for negotiating WNM Collocated Interference Reporting. This
allows hostapd to request associated STAs to report their collocated
interference information and wpa_supplicant to process such request and
reporting. The actual values (Collocated Interference Report Elements)
are out of scope of hostapd and wpa_supplicant, i.e., external
components are expected to generated and process these.

For hostapd/AP, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration. STAs are requested to perform
reporting with "COLOC_INTF_REQ <addr> <Automatic Report Enabled> <Report
Timeout>" control interface command. The received reports are indicated
as control interface events "COLOC-INTF-REPORT <addr> <dialog token>
<hexdump of report elements>".

For wpa_supplicant/STA, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration and setting Collocated
Interference Report Elements as a hexdump with "SET coloc_intf_elems
<hexdump>" control interface command. The hexdump can contain one or
more Collocated Interference Report Elements (each including the
information element header). For additional testing purposes, received
requests are reported with "COLOC-INTF-REQ <dialog token> <automatic
report enabled> <report timeout>" control interface events and
unsolicited reports can be sent with "COLOC_INTF_REPORT <hexdump>".

This commit adds support for reporting changes in the collocated
interference (Automatic Report Enabled == 1 and partial 3), but not for
periodic reports (2 and other part of 3).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-10-30 14:07:51 +02:00
Jouni Malinen
a5e6270f25 OWE: Use shorter scan interval during transition mode search
Start scans more quickly if an open BSS advertising OWE transition mode
is found, but the matching OWE BSS has not yet been seen.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-10-12 19:59:26 +03:00
Sunil Dutt
91073ccaaa OWE: Attempt more scans for OWE transition SSID if expected BSS not seen
This commit introduces a threshold for OWE transition BSS selection,
which signifies the maximum number of selection attempts (scans) done
for finding OWE BSS.

This aims to do more scan attempts for OWE BSS and eventually select the
open BSS if the selection/scan attempts for OWE BSS exceed the
configured threshold.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-10-12 19:59:26 +03:00
Beni Lev
077232f603 OCE: Add OCE capability attribute only when associating to an OCE AP
Signed-off-by: Beni Lev <beni.lev@intel.com>
2018-09-02 18:16:30 +03:00
Ankita Bajaj
af835d75b7 FILS: Fix FILS connect failures after ERP key invalidation
If the RADIUS authentication server dropped the cached ERP keys for any
reason, FILS authentication attempts with ERP fails and the previous
wpa_supplicant implementation ended up trying to use the same keys for
all consecutive attempts as well. This did not allow recovery from state
mismatch between the ERP server and peer using full EAP authentication.

Address this by trying to use full (non-FILS) authentication when trying
to connect to an AP using the same ERP realm with FILS-enabled network
profile if the previous authentication attempt had failed. This allows
new ERP keys to be established and FILS authentication to be used again
for the consecutive connections.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-08-24 16:27:34 +03:00
Bhagavathi Perumal S
d7f038ded2 wpa_supplicant: Add ieee80211ac information in STATUS
This allows user to get current operating mode of station.

Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
2018-05-04 20:18:55 +03:00
Dmitry Lebed
37547ad63c wpa_supplicant: Increase authentication timeout if CAC is started
Timeout is increased by dfs_cac_ms from channel data, or by max CAC time
(10 minutes) if dfs_cac_ms is not defined. This is needed for some more
complex cases, e.g., when STA is acting as an active slave with DFS
offload enabled and decided to start CAC after receiving CONNECT
command, in such a case the 10 second timeout is too small and
wpa_supplicant need to wait for CAC completion or CAC timeout (up to 10
minutes).

Without such timeout modification wpa_supplicant will be unable to
connect to an AP on DFS channel, since the default authentication
timeout (10 s) is smaller than the minimum CAC time (60 s).

Tested with nl80211 DFS offload implementation.

Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
2018-04-15 22:20:49 +03:00
Masashi Honma
e480212765 dbus: Add FILS to global capabilities
If any of the interfaces supports FILS (and similarly for FILS-SK-PFS),
include the "fils" (and "fils_sk_pfs") capability in D-Bus information.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2018-04-02 11:56:06 +03:00
Jouni Malinen
6a252ece24 DPP: Fix GAS query removal race condition on DPP_STOP_LISTEN
If a DPP_STOP_LISTEN call happens to be received when there is a pending
gas-query radio work that has not yet been started, it was possible for
gas_query_stop() to go through gas_query_done() processing with
gas->work == NULL and that ended up with the pending GAS query getting
freed without removing the pending radio work that hold a reference to
the now freed memory. Fix this by removing the pending non-started radio
work for the GAS query in this specific corner case.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-02-07 18:03:58 +02:00
Sunil Dutt
5ff39c1380 SAE: Support external authentication offload for driver-SME cases
Extend the SME functionality to support the external authentication.
External authentication may be used by the drivers that do not define
separate commands for authentication and association
(~WPA_DRIVER_FLAGS_SME) but rely on wpa_supplicant's SME for the
authentication.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-02-02 21:17:55 +02:00
Jouni Malinen
2cb40e9f40 OWE: Try all supported DH groups automatically on STA
If a specific DH group for OWE is not set with the owe_group parameter,
try all supported DH groups (currently 19, 20, 21) one by one if the AP
keeps rejecting groups with the status code 77.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-12-27 21:06:02 +02:00
vamsi krishna
d98038bb05 FILS: Driver configuration to disable/enable FILS features
The new disable_fils parameter can be used to disable FILS functionality
in the driver. This is currently removing the FILS Capability bit in
Extended Capabilities and providing a callback to the driver wrappers.
driver_nl80211.c implements this using a QCA vendor specific command for
now.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-12-15 20:52:17 +02:00
Jouni Malinen
1866dfb52c DPP: Stop pending GAS client operation on DPP_STOP_LISTEN
This makes the operation more complete in stopping all ongoing DPP
related functionality.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-30 00:08:40 +02:00