Using QCA vendor command, allow ACS function to be offloaded to the
driver. Once channels are selected, hostapd is notified to perform OBSS
operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to make following operations behave as expected since
mesh iftypes may prevent various operations (e.g., registering Probe
Request frame RX). Use same design as leave_ibss does to handle this
consistently.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the ignore_if_down_event flag to remain set in some
cases where interface mode change required the interface to be set down
temporarily. If that happened, the following rfkill interface down could
have been ignored and device could have been left trying to scan or
connect (which would all fail due to the interface beign down). Clean
this up by clearing the ignore_if_down_event flag on the interface down
event regardless of whether the interface is up at the time this event
is processed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 6c6678e7a4 ('nl80211: Make
br_ifindex available in i802_bss') did not cover the case where
i802_check_bridge() ends up creating the bridge interface. That left
bss->br_ifindex zero and prevented neighbor addition. Extend that
functionality to update br_ifindex once the bridge netdev has been
added.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add link measurement request to registration of Action frames to be
handled by wpa_supplicant if the driver supports TX power value
insertation.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add Neighbor Report Response Action frame to registration of Action
frames to be handled by wpa_supplicant.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Set the RRM capability flags, based on the capabilities reported
by the underlying driver.
In addition, upon connection, notify the underlying driver regarding
RRM support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
cfg80211 will reject any of these attributes regardless of whether the
values actually change or not when NL80211_CMD_SET_STATION is used for
something else than TDLS. This path is hit at least when setting up
mesh, so filter out the attributes from NL80211_CMD_SET_STATION to match
the rules in cfg80211.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows adding/deleting an IPv6 neighbor entry to/from the bridge,
to which the BSS belongs. This commit adds the needed functionality in
driver_nl80211.c for the Linux bridge implementation. In theory, this
could be shared with multiple Linux driver interfaces, but for now, only
the main nl80211 interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Add ops to notify about TSPECs to add/remove. Additionally, subscribe to
ADDTS/DELTS Action frames to be able to process WMM AC Action frames.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Add a new option "mesh_ht_mode" that specifies the HT mode for the
mesh, with this option on, mesh beacons, actions frames, and probe
responses with include the appropriate HT information elements.
[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows setting a network parameter on the bridge that the BSS
belongs to.
This commit adds the needed functionality in driver_nl80211.c for the
Linux bridge implementation. In theory, this could be shared with
multiple Linux driver interfaces, but for now, only the main nl80211
interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This allows setting a bridge port attribute. Specifically, the bridge
port in this context is the port to which the BSS belongs.
This commit adds the needed functionality in driver_nl80211.c for the
Linux bridge implementation. In theory, this could be shared with
multiple Linux driver interfaces, but for now, only the main nl80211
interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This allows adding/deleting an IPv4 neighbor entry to/from the bridge,
to which the BSS belongs. This commit adds the needed functionality in
driver_nl80211.c for the Linux bridge implementation. In theory, this
could be shared with multiple Linux driver interfaces, but for now, only
the main nl80211 interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
This is an initial step in starting to split the large driver_nl80211.c
implementation into somewhat smaller parts.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to figure out from hostapd control interface
whether an interface had been added to a bridge externally at the time
hostapd interface was enabled or if the interface gets added during
hostapd operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
When a beacon was deleted from the kernel in
wpa_driver_nl80211_deinit_ap(), bss->beacon_set was not cleared so
restarting the AP again was not possible.
Fix this by clearing the variable once the beacon was deleted.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add the following channel flags:
* INDOOR_ONLY: The channel can be used if and only if there is a clear
assessment that the device is operating in an indoor environment, i.e.,
it is AC power.
* CONCURRENT_GO: The channel can be used for instantiating a GO if and
only if there is an additional station interface that is currently
connected to an AP on the same channel or on the same U-NII band
(assuming that the AP is an authorized master).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Use the 'no_ir' notation instead of the 'passive scan' and
'no_ibss' notations to match the earlier change in nl80211.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
For mesh mode to work properly, set supported rates only once.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
This is needed for managing STA entries for mesh use cases.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
sta_info call these to send out the disassoc and deauth frame
which are both not relevent to mesh. So don't send them.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Advertise static/dynamic SMPS mode support (according to the wiphy
feature bits) and pass the configured smps_mode when starting the AP.
Signed-off-by: Eliad Peller <eliad@wizery.com>
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This reverts commit 851b0c5581.
The kernel now has full support for this (and it is turned off
by default for hwsim) so wpa_supplicant should really go back
to autodetecting this so clients don't have to figure out what
to do.
Also add a debug message stating that P2P_DEVICE support is used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Create init_mesh, mesh_join, and mesh_leave actions to kernel.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Convert the driver flags variable to u64 since there was no room for
more flags.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
This allows drivers that implement AP SME internally to generate a
Deauthentication or Disassociation frame with the specified reason code.
This was already done with drivers that use hostapd/wpa_supplicant for
AP SME.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use hostapd_freq_params instead of simple frequency parameter for driver
commands. This is preparation for IBSS configuration to allow use of
HT/VHT in IBSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Commit 97279d8d (after hostap-2.0) dropped frame events from foreign
addresses. Unfortunately this commit did not handle the case where the
interface's MAC address might be changed externally, which other
wpa_supplicant code already handled. This causes the driver to reject
any MLME event because the address from the event doesn't match the
stale address in the driver data.
Changing an interface's MAC address requires that the interface be
down, the change made, and then the interface brought back up. This
triggers an RTM_NEWLINK event which driver_nl80211.c can use to
re-read the MAC address of the interface.
Signed-hostap: Dan Williams <dcbw@redhat.com>
Some drivers need to know the initiator of a TDLS connection in order
to generate a correct TDLS mgmt packet. It is used to determine
the link identifier IE. Pass this information to the driver.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Commit 97ed9a06df ('nl80211: Remove bridge
FDB entry upon sta_remove()') used nl_sock and nl_socket_* functions
which are not compatible with older versions of libnl. Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The FDB entry removal ensures that the traffic destined for a
disassociated station's MAC address is no longer forwarded from the
bridge to the BSS.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
