This command can be used to enroll a network based on a local
network configuration block instead of having to (re-)learn the
current AP settings with wps_er_learn.
A new ctrl_interface command, WPS_CANCEL, can now be used to cancel
a pending or ongoing WPS operation. For now, this is only available
with wpa_supplicant (either in station or AP mode). Similar
functionality should be added for hostapd, too.
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
The AP configuration may change after provisioning, so it is better
not to use the current security policy to prioritize results. Instead,
use WPS Selected Registrar attribute as the main sorting key and use
signal strength next without considering security policy or rate sets.
The non-WPS provisioning case remains as-is, i.e., this change applies
only when trying to find an AP for WPS provisioning.
wps_er_config can now be used to configure an AP. It is similar to
wps_er_learn, but instead of only learning the current AP settings,
it continues to send M8 with the new settings for the AP.
wps_er_start command now takes an optional parameter that can be used
to configure a filter to only allow UPnP SSDP messages from the
specified IP address. In practice, this limits the WPS ER operations
to a single AP and filters out all other devices in the network.
Instead of forcefully deinitializing ER immediately, give it some
time to complete unsubscription and call eloop_terminate() only once
ER code has completed its work.
This will need some additional code in wps_er_pbc() to handle PBC mode
enabling for a single AP only. For now, this can only be expected to work
when the ER is connected to a single AP.
New PINs can now be added to WPS ER. This results in the ER code
using SetSelectedRegistrar to modify AP state so that Enrollees
will be able to notice the actice registrar more easily.
This is the first step in adding support for using wpa_supplicant as a
WPS External Registrar to manage APs over UPnP. Only the device
discovery part is implemented in this commit.
wpa_supplicant can now reconfigure the AP by acting as an External
Registrar with the wps_reg command. Previously, this was only used
to fetch the current AP settings, but now the wps_reg command has
optional arguments which can be used to provide the new AP
configuration. When the new parameters are set, the WPS protocol run
is allowed to continue through M8 to reconfigure the AP instead of
stopping at M7.
The new file wps_nfc.c and ndef.c implements NFC device independent
operation, wps_nfc_pn531.c implements NFC device dependent operation.
This patch is only for the following use case:
- Enrollee = wpa_supplicant
- Registrar = hostapd internal Registrar
Following NFC methods can be used:
- Enrollee PIN with NFC
- Registrar PIN with NFC
- unencrypted credential with NFC
Encrypted credentials are not supported.
Enrollee side operation:
Registrar side operation:
Example configuration.
CONFIG_WPS=y
CONFIG_WPS_NFC=y
CONFIG_WPS_NFC_PN531=y
I used NFC device "NXP PN531". The NFC device access method is
confidential, so I used outer library. Please download below files from
https://www.saice-wpsnfc.bz/index.php
[WPS NFC Library]
WpsNfcLibrary/WpsNfc.h
WpsNfcLibrary/WpsNfcType.h
WpsNfcLibrary/WpsNfcVersion.h
WpsNfcLibrary/linux/libnfc_mapping_pn53x.dll
WpsNfcLibrary/linux/wpsnfc.dll
[NFC Reader/Writer Kernel Driver]
NFCKernelDriver-1.0.3/linux/kobj/sonyrw.ko
<WiFi test>
The hostapd/wpa_supplicant with this patch passed below tests on
"Wi-Fi WPS Test Plan Version 1.6".
4.2.5 Add device using NFC Method with password token
(I used SONY STA instead of NXP STA.)
4.2.6 Add device using NFC Method with configuration token
5.1.9 Add to AP using NFC Method with password token
through internal registrar
(I used SONY AP instead of NXP AP.)
5.1.10 Add to AP using NFC Method with configuration token
through internal registrar
Some WPS APs do not set Selected Registrar attribute to 1 properly when
using an external Registrar. Allow such an AP to be selected for PIN
registration after couple of scan runs that do not find APs marked with
Selected Registrar = 1. This allows wpa_supplicant to iterate through
all APs that advertise WPS support without delaying connection with
implementations that set Selected Registrar = 1 properly.
Change association behavior to match with ap_scan=1 when WPS is used in
ap_scan=2 mode with wildcard SSID matching. In addition, allow hardcoded
BSSID to be used to select AP even if selected registrar attribute is
not present.
Whenever new scan results include WPS AP(s) and the client is not
associated, send a notification message to control interface monitors.
This makes it easier for GUIs to notify the user about possible WPS
availability without having to go through the scan results.
Fragment WPS IE if needed to fit into the IE length limits in hostapd
and Reassemble WPS IE data from multiple IEs in wpa_supplicant.
In addition, moved WPS code from events.c into wps_supplicant.c to clean
up module interfaces.
New control interface commands WPS_PBC, WPS_PIN, and WPS_REG can be used
to start WPS processing. These add and select the WPS network block into
the configuration temporarily, i.e., there is no need to add the WPS
network block manually anymore.
The wps_context data is now managed at wpa_supplicant, not EAP-WSC. This
makes wpa_supplicant design for WPS match with hostapd one and also
makes it easier configure whatever parameters and callbacks are needed
for WPS.
This cleans up the internal interface between different modules and is
the first step in getting wpa_supplicant design closer to hostapd as far
as WPS is concerned.
