Each attempt to connect to the same network using WPS would result
in the duplicate configuration getting added. Avoid such redundant
additions by comparing the network configuration with an already
existing one and remove the older network if the new credential
provisioned through WPS is identical.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
nl80211 has obsoleted WEXT as the preferred kernel interface for
controlling wireless drivers. Update wpa_supplicant driver interface
list order so that nl80211 gets used first if both nl80211 and wext
interfaces are included in the build. In addition, update README to
reflect the fact that WEXT is obsolete.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There are quite a few places in the current implementation where a nul
terminated string is generated from binary data. Add a helper function
to simplify the code a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
The nfcpy script used to be run in a way that left them running for
multiple operations. This is not desired for some use cases, so provide
options to request only a single operation to be performed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
NFC connection handover messages may be longer than 100 octets, so
increase wpa_cli buffer size to allow longer messages to be reported.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reset ft_completed if STA receives deauthentication
between FT reassoc success and the subsequent initial
mobility authentication and association.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only explicit indications of authentication failures were
used to disable a network block temporarily. Extend this to use multiple
failed connection attempts as a sign of a possible authentication or
authorization failure to reduce the frequency of connection attempts
with a network that does not seem to allow connection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The fast-connect optimization to skip a new scan did not update how the
RSN preauthentication callback is used. There is no point in trying to
add preauthentication candidates from cases where scan was skipped, so
skip this call, too, in such cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
All wpa_supplicant_deinit_iface() callers ended up freeing wpa_s
immediately after this call. Move os_free(wpa_s) into the deinit
function to share the same call and make the deinit sequence clearer.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add "EAPLogoff" and "EAPLogon" interface DBus commands which
parallel the "logoff" and "logon" wpa_ctrl commands which terminate
and restart EAP authentication. Slightly enhance the "logon" case
by expiring any running "startWhile" timer.
Signed-hostap: Paul Stewart <pstew@chromium.org>
This option can be used only for global parameters that are not going
to be changed from settings.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Iliyan Malchev <malchev@google.com>
Add "get_capability freq" command to print a more verbose list of
channels and frequencies in MHz. The tag "NO_IBSS" is added, if IBSS
mode is not allowed on a channel. This allows userspace programs to get
the frequencies and limitations associated with each channel.
This extends the information already provided in "get_capability
channels" but a new interface is chosen because of backwards
compatibility considerations.
Signed-hostap: Bruno Randolf <br1@einfach.org>
Harmonize EAP status events over control interface to provide same
functionality as existing D-Bus callback.
Signed-hostap: Chris Hessing <chris.hessing@cloudpath.net>
"WPS_NFC_CONFIG_TOKEN <WPS/NDEF> <network id>" can now be used to build
an NFC configuration token from a locally configured network.
Signed-hostap: Jouni Malinen <j@w1.fi>
This extends the WPS ER commands that previously accepted only UUID as
an identifier for an AP to use either UUID or BSSID for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
There may be cases where multiple BSS entries for a single BSSID are in
the table. This is mostly in automated test cases due to the AP
configuration changes, but something similar could potentially happen as
a corner case in more realistic networks, too, e.g., when an AP changes
its operating channel. Make network selection more robust by trying to
find the exact BSS entry instead of any BSS entry with a matching BSSID
when storing GAS/ANQP response.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some extended capabilities (I'm currently interested in "Operating Mode
Notification" for VHT) are implemented by the kernel driver and exported
in nl80211. Use these in hostapd/wpa_supplicant.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This is mainly for testing purposes where it is convenient to have an
easy way of getting wpa_supplicant state cleared between test cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
If WPS provisioning step is completed with an AP that is in WPS
configured state, we can skip a second scan after the provisioning step
since the AP is unlikely to change its configuration in such a case.
This can speed up WPS connection a bit by removing an unneeded scan.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
This can be used to configure wpa_supplicant to ignore old scan results
from the driver cache in cases where such results were not updated after
the scan trigger from wpa_supplicant. This can be useful in some cases
where the driver may cache information for a significant time and the AP
configuration is changing. Many such cases are for testing scripts, but
this could potentially be useful for some WPS use cases, too.
Signed-hostap: Jouni Malinen <j@w1.fi>
The after_wps counter could have potentially be left in its old non-zero
value in some WPS sequences which could result in a single-channel scan
being used based on obsolete information. Clear after_wps in
wpas_wps_reassoc() to make sure this does not happen.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the AP (P2P GO) has changes its channel of SSID recently, the BSS
table may have multiple entries for a BSSID. Select the one which was
most recently updated for WPS/P2P operations in such case to increase
the likelihood of using current information.
Signed-hostap: Jouni Malinen <j@w1.fi>
Select the BSS entry based on BSSID,SSID pairs instead of just BSSID to
avoid selecting an unexpected SSID for the ROAM command.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit b277a2bebc added a new global
configuration parameter, but forgot to update configuration file saving
to store this.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new parameter allows wpa_supplicant AP mode operations to use
similar design to the vendor_elements parameter in hostapd to add
vendor_elements into Beacon/Probe Response IE parameters.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
sta_scan_pending was supposed to be accurate enough for determining
whether a P2P scan needs to be postponed. However, it has turned out
that there were cases where sta_scan_pending was not cleared properly.
While the known cases have now been addressed, it is possible that some
other cases may still exist. To avoid issues with P2P operationg getting
stuck, verify more carefully that there is a real pending station mode
scan (either in progress or scheduled to be requested).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Scan result events are shared between all virtual interfaces sharing the
same radio. However, some of the steps are not really appropriate on
virtual interfaces that did not issue the scan request. Fix this by
making these steps conditional on the scan results being processed on
the interface that requested them.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There were couple of code paths that could end up stopping station mode
scanning without clearing sta_scan_pending. This could result in P2P
search getting stuck waiting for completion of station mode scan which
would never show up. Fix this by calling wpas_p2p_continue_after_scan()
in cases where station mode scans are stopped. This allows
sta_scan_pending to be cleared and P2P search operation continued.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make the implementation more consistent and cleaner by using a single
function for addressing all the cases where completion of a station mode
scan operation allows a P2P operation (search) to be re-started.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. This is similar to the Makefile
change in commit ad3872a372.
Signed-hostap: Jouni Malinen <j@w1.fi>
This code was within ifdef CONFIG_AP and did not get included unless
AP mode support was also enabled. This is similar to the Makefile
change in commit 2dfb9a447c.
Signed-hostap: Jouni Malinen <j@w1.fi>
This fixes the lookup of a usable PMKSA entry in the cache. Using
wpa_s->current_ssid often returns nothing when a usable PMKSA exists in
the cache since wpa_s->current_ssid does not necessarily point to the
correct network entry at this point in time (prior to association).
Signed-hostap: Partha Narasimhan <parthan@gmail.com>
Add a driver capability flag for drivers which support IBSS mode and set
it for nl80211 drivers which have set the NL80211_IFTYPE_ADHOC.
Add a new option "modes" to "get_capability" which will return "AP" and
"IBSS" if the corresponding capability flags are set.
The idea is that this can be used for UIs to find out if the driver
supports IBSS mode.
Signed-hostap: Bruno Randolf <br1@einfach.org>
If a peer replies to persistent group invitation with status code 8
(unknown group), remove the peer from the p2p_client_list if we are the
GO or remove the persistent group if we are the P2P client since it
looks like that the peer has dropped persistent group credentials and
the provisioning step needs to be executed again.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_ignore_shared_freq=1 in the configuration file (or "SET
p2p_ignore_shared_freq 1" on control interface) can now be used to
configure wpa_supplicant to ignore the preference on shared operating
channel when the driver support multi-channel concurrency. The default
behavior is to try to start any new P2P group on an operating channel
that is already in use on another virtual interface to avoid extra cost
from hopping between multiple channels. If this new parameter is set to
1, such preference is not used and instead, the channel for the new P2P
group is selected based on other preferences while ignoring operating
channels of any concurrent connection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 50285f5ca8 changed number of rules
in channel selection and among other things, it broke the design where
the currently used operating channel on a virtual interface that is
shared by the same radio is preferred to avoid costs related to
multi-channel concurrency. Fix this regression by making the P2P module
aware of the shared channel and using that preference as the highest
priority when re-selecting the channel during negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
