Commit graph

280 commits

Author SHA1 Message Date
Jouni Malinen
74781dfc7b Lower RX_MGMT driver event debug level for Beacon frames
This event can be very frequent in AP mode when Beacon frames from
neighboring BSSes are delivered to user space. Drop the debug
message priority from DEBUG to EXCESSIVE for Beacon frames.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 21:48:25 +02:00
Jouni Malinen
5928411e91 Fix compiler warning with CONFIG_NO_SCAN_PROCESSING=y
Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:14:09 +02:00
Jouni Malinen
c3f4278445 P2P: Add group ifname to P2P-PROV-DISC-* events
If Provision Discovery Request is sent for GO role (i.e., P2P Group ID
attribute is included), add the group interface name to the control
interface event on the GO. This makes it easier to figure out which
ctrl_iface needs to be used for wps_pbc/wps_pin command to authorize
the joining P2P client.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-06 21:57:17 +02:00
Jouni Malinen
d00821e913 Try to reconnect to the same BSS on recoverable disconnection
If the AP disconnects us with a reason code that indicates that it has
dropped the association, but could allow us to connect again, try to
reconnect to the same BSS without going through the full scan. This can
save quite a bit of time in some common use cases, e.g., when inactivity
timeout is used on the AP (and especially, when waking up from suspend
which has likely triggered some timeout on the AP).

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-04 21:57:14 +02:00
Jouni Malinen
bfba8deb8b Update internal MAC address on EVENT_INTERFACE_ENABLED events
This allows the MAC address of the interface to be changed when the
interface is set down even if the interface does not get completed
removed and re-added.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-03 13:20:40 +02:00
Jouni Malinen
56d24b4ee0 Call wpas_connection_failed() only if actually trying to connect
A disconnection event from the driver may end up getting delivered at a
time when wpa_supplicant is not even trying to connect (e.g., during a
scan that was already started after WPS provisioning step). In such a
case, there is not much point calling wpas_connection_failed() and
skipping this avoids confusing attempts of re-starting scanning while
the previous scan is still in progress.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-01 18:22:56 +02:00
Jouni Malinen
f7da5a9ef4 Make reconnect-on-disassoc debug prints somewhat more helpful
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-01 18:22:10 +02:00
Jouni Malinen
0bf927a03e Use wpa_key_mgmt_*() helpers
This cleans up the source code and makes it less likely that new AKM
addition misses some needed changes in the future.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-11-24 22:47:46 +02:00
Johannes Berg
dd840f793c AP: Add explicit EAPOL TX status event
The new event can be used when EAPOL TX status can't be reported as a
complete 802.11 frame but is instead reported as just the EAPOL data as
originally passed to hapd_send_eapol().

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2011-11-19 13:00:30 +02:00
Jouni Malinen
39185dfa54 P2P: Wait until ongoing scan completes before starting P2P find
The P2P_FIND command was failing if it was issued at the moment when
a scan operation was in progress. Avoid returning failure in this
case by scheduling the P2P find to start once the ongoing scan is
completed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-15 21:28:35 +02:00
Ben Greear
6c3771d7d5 Print human readable driver event names
This makes it easier to understand the event related logs.

Signed-hostap: Ben Greear <greearb@candelatech.com>
2011-11-13 19:01:38 +02:00
Jouni Malinen
1bbff09ec5 Process RSN pre-authentication candidates when skipping roam
wpa_supplicant_rsn_preauth_scan_results() needs to be called to
update RSN pre-authentication candidates. This cannot be done before
the wpa_supplicant_connect() call on the first association, but when
trying to figure out whether to roam, it is fine to do so for the
case when roaming is skipped.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-10-30 22:37:12 +02:00
Jouni Malinen
01a1749156 Fix TKIP countermeasures stopping in deinit paths
The eloop timeout to stop TKIP countermeasures has to be canceled
on deinit path to avoid leaving bogus timeouts behind.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-10-30 12:53:20 +02:00
Jouni Malinen
a6d94e1b56 Skip rate set matching if BSS frequency is not known
At least with driver_test.c, the BSS table may not include frequency
information. In such a case, we need to skip rate set matching during
BSS selection to avoid rejecting valid AP.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-10-30 11:46:13 +02:00
Jithu Jance
5cbd88d921 P2P: Fix wpa_supplicant crash on P2P WPS PBC overlap case
Once PBC overlap detected when using dynamic group interfaces, the wpa_s
corresponding to P2P group interface is freed. This patch avoids
accessing the wpa_s data structure after it is freed. This fixes a
possible crash in P2P client role in such a case.
2011-10-24 23:37:39 +03:00
Arik Nemtsov
8f15f711c5 TDLS: Implement low-ack event for lost TDLS peers
Disable the direct connection when a TDLS peer stops responding
to packets, as indicated by the "LOW ACK" event coming from a driver.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
2011-10-23 22:19:08 +03:00
Arik Nemtsov
7de27409a2 TDLS: Support sending a teardown frame from usermode
When a driver does not implement the TDLS_TEARDOWN operation internally,
send an explicit TDLS link teardown frame to the driver.

Change all teardown calls to use these calling semantics.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
2011-10-23 22:18:49 +03:00
Arik Nemtsov
35287637cc TDLS/nl80211: Support receiving TDLS discovery response frames
Register for the TDLS discovery response public action frame in nl80211.
Print out a debug message when a Discovery Resp frame is received and
validated.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
2011-10-23 22:18:35 +03:00
Christian Lamparter
e1e8cae3c7 wpa_supplicant: Check rate sets before joining BSS
IEEE Std 802.11-2007 7.3.2.2 demands that in order to join a BSS all
required basic rates have to be supported by the hardware.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2011-10-23 17:21:50 +03:00
Jouni Malinen
b832d34c48 Comment out scard initialization code if PCSC_FUNCS is not set 2011-10-23 12:24:36 +03:00
Jouni Malinen
17fbb751e1 Remove user space client MLME
This code was used only with driver_test.c to allow MLME operations
in hostapd to be tested without having to use a real radio. There
are no plans on extending this to any other use than testing and
mac80211_hwsim has now obsoled the need for this type of testing.
As such, we can drop this code from wpa_supplicant to clean up the
implementation of unnecessary complexity.
2011-10-22 22:45:38 +03:00
Johannes Berg
9b90955ec7 AP: Pass only bssid/addr/wds to EVENT_RX_FROM_UNKNOWN 2011-10-20 21:51:32 +03:00
Johannes Berg
bcf24348ed AP: Do station poll in driver wrapper
This offloads the station polling to driver wrappers, which may offload
it again to the driver. The hostap driver wrapper uses "real" data
frames while nl80211 uses null data frames.

Also add a specific event to indicate that a poll was successful for
future use with the nl80211 driver.
2011-10-20 21:03:08 +03:00
Jouni Malinen
71269b3708 WNM: Add BSS Transition Management Request for ESS Disassoc Imminent
"hostapd_cli ess_disassoc (STA addr) (URL)" can now be used to send
an ESS Dissassociation Imminent notification to the STA. This event
is shown in wpa_supplicant ctrl_iface monitors (e.g., wpa_cli):
"WNM: ESS Disassociation Imminent - session_info_url=http://example.com/session/"
2011-10-16 23:55:34 +03:00
Gurumoorthi Gnanasambandhan
783fcb7d03 Allow drivers to indicate WPS push button in station mode
EVENT_WPS_BUTTON_PUSHED wpa_supplicant_event can now be used in
station mode driver_*.c to indicate that a push button has been
pushed. This will activate WPS PBC mode.
2011-10-16 18:05:55 +03:00
Luciano Coelho
a4cba8f1e2 Use sched_scan in driver init
This patch uses sched_scan, if available, when the driver is
initialized. It also adds a couple of cancel operations where
appropriate.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-15 18:53:13 +03:00
Luciano Coelho
cbdf3507e9 Add scheduled scan driver operations
In new Linux kernel versions (>=3.0), nl80211 adds scheduled scan
capability. In order to use this feature to its full extent, we need
to support it in the wpa_supplicant core, so that it can also be used
by other drivers.

This commit adds initial scheduled scan support operations and events.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-15 18:53:13 +03:00
Zhi Chen
7d232e23e2 Allow wildcard SSID to be used with WPA-PSK if bssid is set
This allows the AP to be selected based on the BSSID when WPA-PSK
is used with a passphrase. The PSK will be derived from the passphrase
after the SSID has been learned from scan results.
2011-09-30 22:05:44 +03:00
Jouni Malinen
24f6497c34 GAS: Use off-channel operations for requests
This separates off-channel Action frame TX/RX from P2P into a generic
implementation that can now be used both for P2P and GAS needs.
2011-09-29 22:19:51 +03:00
Jouni Malinen
04ea7b7947 GAS: Add a generic GAS query module
This implements GAS request mechanism that is aimed at being used to
replace use case specific GAS/ANQP implementations in the future.
Compared to the earlier implementation in P2P SD, this implementation
includes support for multiple concurrent requests and more thorough
validation of frames against the pending query data.

GAS header processing, including comeback and reassembly, are handled
within gas_query.c and the users of this module will only need to
provide the Query Request and process the (possibly reassembled)
Query Response.
2011-09-29 22:19:15 +03:00
Jouni Malinen
22628eca34 Support driver-based BSS selection in ap_scan=1 mode
If the driver indicates that it supports BSS selection (including
roaming within an ESS) with WPA_DRIVER_FLAGS_BSS_SELECTION, modify
ap_scan=1 mode to behave like ap_scan=2 mode for BSS selection.

The initial scan is still done to avoid the need for strict
configuration of or security parameters (e.g., to figure out whether
TKIP or CCMP is being used as the group cipher). However, when
requesting the driver to connect, the bssid and freq parameters are
not provided to leave the driver in control of selecting which BSS
to use and to allow the driver to decide when to roam.
2011-09-26 14:57:23 +03:00
Jouni Malinen
04a85e4401 P2P: Filter Probe Request frames based on DA and BSSID in Listen state
Only accept Probe Request frames that have a Wildcard BSSID and a
destination address that matches with our P2P Device Address or is the
broadcast address per P2P specification 3.1.2.1.1.
2011-07-15 20:28:46 +03:00
Johannes Berg
b14a210ce2 nl80211: Support GTK rekey offload
Add support to wpa_supplicant for device-based GTK rekeying. In order to
support that, pass the KEK, KCK, and replay counter to the driver, and
handle rekey events that update the latter.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-07-12 21:22:51 +03:00
Hong Wu
8fd0f0f323 FT: Clear SME ft_used/ft_ies when disconnecting
Previous ft_ies needs to be removed before supplicant starts a new FT
initial association and this requires the ft_used state to be cleared
here.

Signed-off-by: Hong Wu <hong.wu@dspg.com>
2011-07-05 21:17:31 +03:00
Jouni Malinen
ca62e114aa wpa_supplicant AP: Disable AP mode on disassoc paths
Regardless of how the AP mode is disabled, wpa_supplicant_ap_deinit()
must be called. Make sure this happens on all paths by calling the
deinit function from wpa_supplicant_mark_disassoc().
2011-07-05 16:38:30 +03:00
Jouni Malinen
29fbc52251 Fix AP selection to check privacy mismatch and IBSS with WPA/RSN IE
These checks were previously skipped if the scan result included WPA
or RSN IE. However, that can result in selecting a network that does
not match local configuration in some cases.
2011-06-23 15:39:00 +03:00
Jouni Malinen
6d28fb9627 Fix regression in RSN pre-authentication candidate list generation
Processing of the scan results for RSN pre-authentication candidates
was moved to happen before the network was selected. This resulted in
all candidates being dropped due to no SSID having been configured.
Fix this by moving the processing to happen after the network has
been selected. Since the raw scan results are not available at that
point, use the BSS table instead of scan results to fetch the
information.
2011-05-19 17:52:46 +03:00
Jouni Malinen
117e812d06 Update BSS table entry if roaming event indicates frequency change
This is needed to make sure the frequency in the BSS table entry
remains up-to-date if the AP changes its operating frequency.
2011-05-16 19:19:30 +03:00
Jouni Malinen
5dac11e027 WPS: Use strict validation of (Re)AssocResp only if IEs are known 2011-04-14 02:57:24 +03:00
Jouni Malinen
b211f3eb71 Add sanity checks to EVENT_RX_PROBE_REQ event data
Both the SA and IEs from the received Probe Request frames must be
included and the Probe Request RX callback functions may assume that
these are not NULL.
2011-04-14 02:39:25 +03:00
Dmitry Shmidt
67b9bd089b Make scan interval configurable
It is now possible to configure the the time in seconds that
wpa_supplicant waits before requesting a new scan after failing to find
a suitable network in scan results.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2011-04-11 23:14:38 +03:00
Jouni Malinen
c2197bc9bc Return NULL instead of 0 as the pointer on error case 2011-04-08 19:16:20 +03:00
Jouni Malinen
c2f1fe41c2 Fix WPA/WPA2 AP rejection on parameter mismatch
If WPA/WPA2 was enabled in the configuration, the non-WPA exception
could allow an incorrect AP to be selected from scan results. Do
not use the exception if WPA/WPA2 is enabled in configuration.
2011-04-08 19:13:58 +03:00
Jouni Malinen
78177a000e RSN IBSS: Restart IBSS state machines for each new IBSS
Change the old design of running a single long living RSN IBSS
instance to keep a separate instance for each IBSS connection.
This fixes number of issues in getting keys set properly for
new connections and is in general quite a bit more correct
design.
2011-03-23 21:15:46 +02:00
Paul Stewart
cfe53c9aa5 wpa_supplicant: Start bgscan on COMPLETED, not ASSOCIATED
Move the code snippet to switch on bgscan over to wpa_supplicant.c
from event.c, so that it can be activated on wpa_supplicant_set_state().
Also create a centralized place to switch off bgscan. bgscan is now
turned on in COMPLETED, not ASSOCIATED.
2011-03-20 12:27:03 +02:00
Johannes Berg
c202f19c68 wpa_s AP mode: propagate scan event
When wpa_s scans in AP mode, it doesn't propagate the scan event to the
AP code, so that code can get stuck if it uses the callbacks there.
Simply call them where appropriate.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-19 13:08:08 +02:00
Xi Chen
ea244d2156 IBSS RSN: Clear IBSS RSN peers based on peer lost events 2011-03-18 17:04:46 +02:00
Xi Chen
df41824501 IBSS RSN: Do not start if not yet connected to IBSS
This is used to avoid starting IBSS RSN processing with a peer before
the IBSS connection itself has been completed.
2011-03-16 16:26:26 +02:00
Jouni Malinen
52c9e6f3f5 TDLS: Do not allow setup to be started if AP prohibits TDLS 2011-03-06 14:54:49 +02:00
Ganesh Prasadh
281ff0aa76 TDLS: Add initial support for TDLS (IEEE Std 802.11z-2010) 2011-03-06 14:53:49 +02:00
Shan Palanisamy
39b08b5fc0 Indicate assoc vs. reassoc in association event
This allows driver wrappers to indicate whether the association was
done using Association Request/Response or with Reassociation
Request/Response frames.
2011-03-06 14:31:46 +02:00
Johannes Berg
8fd7dc1b1c P2P: Add new_device flag to dev_found callback
The DBus code will want to have perfect matching of dev_found and the
dev_lost it adds so it doesn't need to keep track internally. Enable
that with a new flag in the core that tracks whether we have already
notified about this -- the existing users can ignore it.

The part where this is always set to 1 if the new device is discovered
by a driver that has P2P in the driver is buggy -- the driver should
feed the P2P peer database and then that should feed the notification
here instead.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 21:59:58 +02:00
Konguraj(Raj) Kulanthaivel
c5db8e5170 P2P: Embed publically visible struct in peer info
This embeds some information about each P2P peer that will be publically
visible in a struct that is shared.

The dev_found notification function is also passed the new struct, which
requires some work for the driver-based P2P management.

Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Fabien Marotte <fabienx.marotte@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 21:51:17 +02:00
Ben Greear
e29853bbff SME: Add timers for authentication and asscoiation
mac80211 authentication or association operation may get stuck for some
reasons, so wpa_supplicant better use an internal timer to recover from
this.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2011-02-24 16:59:46 +02:00
Jouni Malinen
16a83d2965 FT: Set EAPOL state machined to authenticated state with FT-EAP
When FT protocol run is completed with FT-EAP, the EAPOL state machine
needs to be notified of the completed authentication to make sure it
does not try to start new authentication.
2011-02-20 21:57:53 +02:00
Ben Greear
e1504976f1 Do not propagate bad scan results to siblings sharing the radio
This decreases useless work and re-scans by siblings when a
device gets a scan failure.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2011-02-16 18:55:37 +02:00
Ben Greear
f049052b9e Use wpa_msg() instead of wpa_printf()
This converts number of debugging messages to use wpa_msg() in order
to allow the interface name to be shown with the messages.

A new function, wpa_dbg(), is introduced to allow
CONFIG_NO_STDOUT_DEBUG=y builds to remove the debug strings. This is
otherwise identical with wpa_msg(), but it gets compiled out if stdout
debugging is disabled.
2011-02-10 20:14:46 +02:00
Jouni Malinen
e67b55fb11 wpa_s AP: Deliver EVENT_RX_PROBE_REQ events to AP processing
This is needed to allows WPS PBC session overlap detection to work
with drivers that process Probe Request frames internally. This
code is is run in hostapd, but the wpa_supplicant AP mode did not
have call to the hostapd_probe_req_rx() function even though it
registered handlers for hostapd Probe Request RX callbacks.
2011-02-08 14:32:35 +02:00
Jouni Malinen
98ea943177 Set portValid=TRUE on association for driver-based 4-way handshake
This was previously done for WPA/WPA2-Personal as part of association
processing when the driver is implementing 4-way handshake. The
portValid needs to be done for WPA/WPA2-Enterprise to get the proper
EAPOL authentication completed callback to configure PMK to the driver.
2011-02-01 00:04:02 +02:00
Jouni Malinen
50b05780c2 IBSS RSN: Delay setting of the initial TX GTK
The driver may get confused if we set the initial TX GTK before having
fully configured and connected to an IBSS, so better delay this
operation until the connection (join/start IBSS) has been completed.
2011-01-15 14:07:02 +02:00
Jouni Malinen
df83fb7d00 Fix wpa_supplicant_ssid_bss_match() handler for non-WPA
The proto configuration may be left to non-zero when moving from one
configuration to another. To avoid misidentifying a network
configuration as enabling WPA, check key_mgmt field, too.
2010-12-30 18:27:33 +02:00
Jouni Malinen
3ac17eba31 P2P: Add initial support for driver-based P2P management
This adds partial callbacks and events to allow P2P management to be
implemented in a driver/firmware. This is not yet complete and is
very much subject to change in the future.
2010-12-30 12:48:55 +02:00
Johannes Berg
0d7e5a3a29 Allow AP mode to disconnect STAs based on low ACK condition
The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2010-12-28 17:15:01 +02:00
Jouni Malinen
cc5e390d28 WPS: Require PBC match with wps_pbc that specifies BSSID
The WPS mode was already verified when the AP was configured for
WPA/WPA2, but this was not done with AP that was in open mode.
Fix this by allowing wpa_supplicant_ssid_bss_match() to be called
in non-WPA configuration, too. With this change, wps_pbc BSSID
command will wait until the specified target AP is in active PBC
mode before trying to connect to it.
2010-12-28 08:56:23 +02:00
Jouni Malinen
7d878ca769 Use SA Query procedure to recovery from AP/STA state mismatch
If a station received unprotected Deauthentication or Disassociation
frame with reason code 6 or 7 from the current AP, there may be a
mismatch in association state between the AP and STA. Verify whether
this is the case by using SA Query procedure. If not response is
received from the AP, deauthenticate.

This implementation is only for user space SME with
driver_nl80211.c.
2010-12-19 11:58:00 +02:00
Johannes Berg
860fddbb41 Allow setting scan_res_handler from the callback function
Some new code I'm working on will need the scan_res_handler assigned all
the time in certain circumstances, so the easiest way is to reset it
within the handler. This is currently prevented by the way the code in
the event handler works -- change that to permit such usage.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2010-12-17 15:31:05 +02:00
Jouni Malinen
df4bc5091e IBSS RSN: Do not start 4-way handshake unless RSN is enabled 2010-12-04 18:17:05 -08:00
Ben Greear
6859f1cb24 Enable sharing of scan result events among virtual interfaces
When controlling multiple virtual interfaces on the same physical
radio, share the scan results events with sibling interfaces. This
decreases the time it takes to connect many virtual interfaces.

This is currently only supported on Linux with cfg80211-based
drivers when using nl80211 or wext driver interface.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2010-11-26 21:46:30 +02:00
Ben Greear
c577db2afd Add interface name to some debug prints
This makes it easier to figure out what is happening when controlling
multiple interfaces from a single wpa_supplicant process.
2010-11-26 21:16:36 +02:00
Jouni Malinen
c05d6d188c Do not segfault on EVENT_ASSOC_REJECT without BSSID 2010-11-26 17:38:46 +02:00
Jouni Malinen
0fb337c121 Extend load balancing optimization in BSS blacklisting
Move the previously SME specific optimization code into generic
function that can be used from non-SME code, too, and use it to
handle disconnection events. In other words, allow disconnection
event to trigger similar optimized scanning case to handle a
common load balancing mechanism. If there is another BSS in the
same ESS when we receive a disconnection event, scan only the
known frequencies of such other BSSes on the next attempt to
speed up recovery.
2010-11-26 11:36:03 +02:00
Jouni Malinen
5471c3434e Blacklist BSS on first failure if only a single network is enabled
The special case of requiring blacklisting count to be 2 or higher
is only needed when more than a single network is currently enabled.
As such, we should not do that when only a single network is enabled.
This make the station more likely to follow network side load
balancing attempts where the current AP may disassociate us with
an assumption that we would move to another AP.
2010-11-26 11:23:50 +02:00
Jouni Malinen
3c85f144ce P2P: Fix Action frame sending after disconnection
assoc_freq needs to be cleared when an interface gets disconnected.
This fixes an issue where P2P Action frame transmission may fail
because of missing remain-on-channel operation when using the same
interface for group operations (or non-P2P connections) and P2P
management operations.
2010-11-25 16:04:07 +02:00
Jouni Malinen
7a80af658d Fix CONFIG_AP=y build without CONFIG_P2P=y 2010-11-24 16:55:17 +02:00
Albert Liu
1d39378a0b P2P: Fix RX ack status on Action frames sent via interface in GO mode
The wpa_supplicant_event() EVENT_TX_STATUS ack field needs to be
converted to use wpas_send_action_tx_status()
enum p2p_send_action_result in this case, too, to avoid getting
incorrect TX status for P2P processing.
2010-11-24 14:25:33 +02:00
Jouni Malinen
bbb921daaa Maintain internal entropy pool for augmenting random number generation
By default, make hostapd and wpa_supplicant maintain an internal
entropy pool that is fed with following information:

hostapd:
- Probe Request frames (timing, RSSI)
- Association events (timing)
- SNonce from Supplicants

wpa_supplicant:
- Scan results (timing, signal/noise)
- Association events (timing)

The internal pool is used to augment the random numbers generated
with the OS mechanism (os_get_random()). While the internal
implementation is not expected to be very strong due to limited
amount of generic (non-platform specific) information to feed the
pool, this may strengthen key derivation on some devices that are
not configured to provide strong random numbers through
os_get_random() (e.g., /dev/urandom on Linux/BSD).

This new mechanism is not supposed to replace proper OS provided
random number generation mechanism. The OS mechanism needs to be
initialized properly (e.g., hw random number generator,
maintaining entropy pool over reboots, etc.) for any of the
security assumptions to hold.

If the os_get_random() is known to provide strong ramdom data (e.g., on
Linux/BSD, the board in question is known to have reliable source of
random data from /dev/urandom), the internal hostapd random pool can be
disabled. This will save some in binary size and CPU use. However, this
should only be considered for builds that are known to be used on
devices that meet the requirements described above. The internal pool
is disabled by adding CONFIG_NO_RANDOM_POOL=y to the .config file.
2010-11-24 01:29:40 +02:00
Anil Gathala Sudha
7cfc4ac319 P2P: Add support for automatic channel selection at GO
The driver wrapper may now indicate the preferred channel (e.g., based
on scan results) on both 2.4 GHz and 5 GHz bands (and an overall best
frequency). When setting up a GO, this preference information is used
to select the operating channel if configuration does not include
hardcoded channel. Similarly, this information can be used during
GO Negotiation to indicate preference for a specific channel based
on current channel conditions.

p2p_group_add command can now use special values (freq=2 and freq=5)
to indicate that the GO is to be started on the specified band.
2010-11-10 13:33:47 +02:00
Jouni Malinen
43882f1efc Allow TSN AP to be selected when configured for WEP
Commit d8d940b746 introduced a regression
that prevented TSN APs from being used with WEP since the AP was
rejected if it advertised WPA or RSN IE when we were configured to use
WEP. Resolve this by checking whether the AP is advertising a TSN, i.e.,
whether the AP allows WEP to be used as a group cipher. If so, allow
the AP to be selected if we are configured to use static WEP or
IEEE 802.1X (non-WPA).

It should be noted that this is still somewhat more restricted in AP
selection than earlier wpa_supplicant branches (0.7.x or older) that
ignore the WPA/RSN IE completely when configured for non-WPA.
2010-11-08 21:14:32 +02:00
Jouni Malinen
ea78c315a2 Add ctrl_interface event for association rejected 2010-10-27 20:28:16 +03:00
Jouni Malinen
c973f3868a P2P: Remove P2P group on driver resource becoming unavailable
Add a new driver event, EVENT_INTERFACE_UNAVAILABLE, for indicating
that the driver is not able to continue operating the virtual
interface in its current mode anymore, e.g., due to operating
channel for GO interface forced to a DFS channel by another virtual
interface.

When this happens for a P2P group interface, the P2P group will
be terminated and P2P-GROUP-REMOVED event shows the reason for
this as follows:
P2P-GROUP-REMOVED wlan0 GO reason=UNAVAILABLE
2010-10-25 19:16:11 +03:00
Jouni Malinen
35c5d61037 Fix crash on channel list changed event during driver init
The driver wrapper may indicate EVENT_CHANNEL_LIST_CHANGED before
completing init(). This would likely result in segfault when driver
channel list is being read as part of processing this event when
P2P is enabled.
2010-10-20 19:30:55 +03:00
Jouni Malinen
93b7ddd032 P2P: Skip GO Neg Conf ack failure workaround of send failures
The workaround to ignore no ctrl::ack received for GO Negotiation
Confirmation frame was only supposed to be used when the frame was
actually transmitted and just the ack was not received. However, due
to the way the driver failure on transmitting the frame were reported,
this ended up getting applied for all failures in sending the GO
Negotiation Confirmation frame.

Improve this by providing a mechanism to indicate whether send_action
operations fail locally before the frame was actually transmitted or
because of not receiving ack frame after having transmitted the frame.
2010-10-19 12:47:33 +03:00
Jouni Malinen
b5c9da8db3 P2P: Add mechanism for updating P2P channel list based on driver events
This allows P2P channel list to be updated whenever the driver changes
its list of allowed channels, e.g., based on country code from scan
results.
2010-10-15 18:55:22 +03:00
Paul Stewart
174fa7898e bgscan: Add new channel condition parameters to signal change events
bgscan modules can potentially get a richer feel for the channel
condition and make better choices about scan/no-scan and roam/no-roam.
2010-10-12 20:03:36 +03:00
Ben Greear
199716adb3 Fix wpa_supplicant build without CONFIG_WPS and CONFIG_AP 2010-10-07 10:41:58 +03:00
Johannes Berg
9919f7a22b Fix AP mode in wpa_supplicant with interface events
Needs to not trigger a scan here when the AP mode setup sets
interface down/up.
2010-10-06 17:10:07 +03:00
Jouni Malinen
f648bc7d0d WPS: Use blacklist more aggressively during WPS provisioning
This allows more APs to be tried during the WPS timeout.
2010-09-22 11:50:15 -07:00
Jouni Malinen
7736f18bef WPS: Cancel WPS operation on PBC session overlap detection
Previously, wpa_supplicant remaining in scanning state without
trying to connect, but there is no particular need to do that.
Instead, cancel WPS operation completely whenever PBC session
overlap is detected.
2010-09-19 17:04:04 -07:00
Jouni Malinen
ea184114ca Allow auto-connect to request scan in associating state
Disconnection event may be received while in associating state.
Previously, wpa_supplicant could get stuck not trying to reconnect
in that case at least with nl80211. Allow scan request in this
state to avoid the issue. This helps especially with APs that do
load balancing by sending Deauthentication frame as a response to
Reassociation Request frame after successful Authentication frame
exchange.
2010-09-14 00:07:54 -07:00
Ardong Chen
0d0a8ca1cc Add option for disabling automatic reconnection on disconnection
ctrl_interface STA_AUTOCONNECT command can now be used to disable
automatic reconnection on receiving disconnection event. The default
behavior is for wpa_supplicant to try to reconnect automatically, i.e.,
to maintain previous behavior.
2010-09-10 10:30:26 -07:00
Jouni Malinen
b73bf0a74b P2P: Stop connection attempt on PBC session overlap
The overlap condition cannot disappear before group formation timeout
hits, so there is no point in continuing in this case and failure can
be indicated immediately.
2010-09-10 10:30:25 -07:00
Jouni Malinen
9fdd0fada7 P2P: Add disassociation/deauthentication IE notifications 2010-09-09 07:17:18 -07:00
Jouni Malinen
9bae1be0a1 P2P: Map driver events to P2P event notifications 2010-09-09 07:17:18 -07:00
Jouni Malinen
0817de904e P2P: Optimize scan timeouts for group formation 2010-09-09 07:17:17 -07:00
Jouni Malinen
73e492693d P2P: Add TODO note for Group Formation bit use in AP selection 2010-09-09 07:17:17 -07:00
Jouni Malinen
54f489be45 WPS 2.0: Validate WPS attributes in management frames and WSC messages
If CONFIG_WPS_STRICT is set, validate WPS IE(s) in management frames and
reject the frames if any of the mandatory attributes is missing or if an
included attribute uses an invalid value. In addition, verify that all
mandatory attributes are included and have valid values in the WSC
messages.
2010-09-09 06:07:48 -07:00
Jouni Malinen
7f5420691e wpa_supplicant AP: Make sure deauth/disassoc event is valid
Verify that the driver wrapper is using a valid deauth/disassoc
event before dereferencing the addr pointer. The address is required
to be set in AP mode, but it is safer to verify this here than to
trust on all driver wrappers doing the correct thing.
2010-09-04 21:50:12 +03:00
Jouni Malinen
0c703df32d Fix BSS selection with multiple configured networks
Commit d8d940b746 broke the logic on
iterating through all configured network blocks. This was supposed
to continue the loop on mismatch to allow other than the first
configured network to be found.
2010-08-28 12:04:21 +03:00
Jouni Malinen
d8d940b746 Merge WPA and non-WPA network selection routines
This removes quite a bit of duplicated code and allows network block
priority configuration to be used to prefer unprotected networks and
also allows use on open network with good signal strength even if
scan results show a protected network with marginal signal strength
that does not allow it to be used.
2010-08-27 20:05:49 +03:00
Jouni Malinen
60a972a68d Add current signal strength into signal quality change events 2010-08-27 16:58:06 +03:00
Jouni Malinen
2e75a2b3a6 Add more debug info on deauth/disassoc events and commands 2010-08-17 21:04:38 +03:00
Jouni Malinen
24f7694062 Remove get-first-scan-results-before-request optimization
This has already been disabled in most use cases and can result
in problems with some drivers, so better just remove it completely.
2010-07-18 16:11:03 -07:00
Jouni Malinen
9b7124b27f Add some more debug for driver events 2010-07-17 20:33:34 -07:00
Jouni Malinen
5bc0cdb721 Ignore scan results in wpa_supplicant AP mode
This is needed to avoid trying to reassociate based on new scan
results when using wpa_supplicant to control AP mode. This could
happen if something external triggered the driver to run a scan.
2010-07-17 20:32:25 -07:00
Jouni Malinen
3f967fe055 Verify that l2_packet is initialized before notification call
It is possible that l2_packet is not used with wpa_supplicant
in some cases, so better make sure we do not end up notifying
l2_packet code about authentications unless it was actually
initialized in the first place.
2010-07-17 20:26:47 -07:00
Jouni Malinen
c2594c3677 bgscan: Provide scan results to the notify_scan handler 2010-07-10 15:43:44 -07:00
Sam Leffler
3b038d7968 Fix bgscan stopping after dissassociation
Clear bgscan_ssid on disassoc event so bgscan is initialized the next
time we reach COMPLETED state.
2010-07-10 14:43:48 -07:00
Jouni Malinen
f62c2315f7 Show signal level and WPS support in scan results debug dump
This makes it easier to debug AP selection for WPS provisioning.
2010-06-11 13:47:33 -07:00
Jouni Malinen
8401a6b028 Add Linux rfkill support
Add a new wpa_supplicant state: interface disabled. This can be used
to allow wpa_supplicant to be running with the network interface even
when the driver does not actually allow any radio operations (e.g.,
due to rfkill).

Allow driver_nl80211.c and driver_wext.c to start while rfkill is in
blocked state (i.e., when ifconfig up fails) and process rfkill
events to block/unblock WLAN.
2010-05-23 10:27:32 +03:00
Jouni Malinen
0544b24248 Add BSSID and reason code (if available) to disconnect event
This adds more details into the CTRL-EVENT-DISCONNECTED event to
make it easier to figure out which network was disconnected in some
race conditions and to what could have been the reason for
disconnection. The reason code is currently only available with
the nl80211 driver wrapper.
2010-04-11 21:25:15 +03:00
Jouni Malinen
64e58f5189 Add option for overriding scan result handler for a single scan 2010-04-11 19:53:31 +03:00
Jouni Malinen
977b11747f Allow sub-second resolution for scan requests
This is in preparation to use cases that may benefit from more frequent
scanning.
2010-04-11 19:10:01 +03:00
Jouni Malinen
86d4f806da Add ctrl_iface command for triggering a roam to a specific BSS
'wpa_cli roam <bssid>' can now be used to test roaming within an ESS
(e.g., for FT over-the-air). This command will bypass a new scan and
will select the BSS based on the specified BSSID. It is responsibility
of the caller to make sure that the target AP is in the BSS table.
This can be done, e.g., by running a scan before the roam command,
if needed.
2010-04-10 22:56:55 +03:00
Jouni Malinen
e7846b6859 FT: Clean up wpa_sm_set_ft_params() by using common parse
Instead of parsing the IEs in the callers, use the already existing
parser in wpa_ft.c to handle MDIE and FTIE from initial MD association
response. In addition, this provides more complete access to association
response IEs to FT code which will be needed to fix FT 4-way handshake
message 2/4.
2010-04-10 11:36:35 +03:00
Jouni Malinen
579ce77122 FT: Deauthenticate in case of Reassoc Response validation error
If validation of the Reassociation Response frame fails during FT
Protocol, do not allow association to be completed; instead, force
deauthentication.
2010-04-09 16:59:27 +03:00
Jouni Malinen
e2f74005f5 bgscan: Add signal strength change events
This allows bgscan modules to use more information to decide on when
to perform background scans. bgscan_simple can now change between
short and long background scan intervals based on signal strength
and in addition, it can trigger immediate scans when the signal
strength is detected to be dropping.

bgscan_simple takes following parameters now:
short interval:signal strength threshold:long interval
For example:
	bgscan="simple:30:-45:300"
2010-03-28 15:32:34 -07:00
Jouni Malinen
b766a9a293 Add freq_list network configuration parameter
This can be used to limit which frequencies are considered when
selecting a BSS. This is somewhat similar to scan_freq, but will
also affect any scan results regardless of which program triggered
the scan.
2010-03-26 22:45:50 -07:00
Jouni Malinen
62c72d7299 FT: Process reassoc resp FT IEs when using wpa_supplicant SME 2010-03-13 21:13:18 +02:00
Jouni Malinen
fe1919856c FT: Update SME frequency info before sme_associate() call
This is needed to allow FT-over-DS to request correct channel for
the reassociation with the target AP.
2010-03-13 18:26:25 +02:00
Jouni Malinen
71024cb255 FT: Request reassociation after successful FT Action frame exchange 2010-03-13 17:14:41 +02:00
Jouni Malinen
036f7c4aab FT: Add preliminary processing of FT Action Response from EVENT_RX_ACTION
Previously, this was only done with userspace MLME (i.e., driver_test.c);
now, driver_nl80211.c can deliver the FT Action Response (FT-over-DS)
for processing. The reassociation after successful FT Action frame
exchange is not yet implemented.
2010-03-12 00:43:00 +02:00
Jouni Malinen
ac26ebd8b5 Allow roam based on preferred BSSID regardless of signal strength 2010-02-28 11:09:58 +02:00
Jouni Malinen
be8be6717d Clear current_bss pointer on disassociation/deauthentication
This is needed to allow the BSS table entry for the previously used
BSS to be removed. Now wpa_bss_in_use() can return 0 for the last BSS
that was used as soon as deauthentication/disassociation event has been
received.
2010-02-27 18:40:25 +02:00
Jouni Malinen
159dd3e28a Add more debug prints to make deauth/disassoc events clearer 2010-02-27 18:39:09 +02:00
Jouni Malinen
48563d86b2 Try to avoid some unnecessary roaming
When multiple APs are present in scan results with similar signal
strength, wpa_supplicant may end up bounching between them frequently
whenever new scan results are available (e.g., due to periodic scans
requested by NetworkManager). This can result in unnecessary roaming
and in case of the current cfg80211 version, to frequent network
disconnections.

Do not request a roam if the current BSS is still present in the scan
results and the selected BSS is in the same ESS and has only a slighly
stronger signal strength.
2010-01-24 18:19:50 -08:00
Jouni Malinen
70f8cc8ec8 Share the same enum for MFP configuration
The three existing enums were already depending on using the same
values in couple of places and it is just simpler to standardize on
one of these to avoid need for mapping between different enums for
the exact same thing.
2010-01-03 21:02:51 +02:00
Jouni Malinen
9ba9fa07cc Move wpa_supplicant specific scan code away from src/drivers
This fits better in wpa_supplicant/scan.c. Couple of remaining
scan_helpers.c functions are currently used in driver wrappers,
but they can likely be removed in the future.
2010-01-03 18:48:11 +02:00
Jouni Malinen
1d041bec84 Use generic driver event notification for AP mode assoc/disassoc 2010-01-03 18:22:22 +02:00
Jouni Malinen
a8e0505bf0 Use driver event, EVENT_EAPOL_RX, for EAPOL frame indication 2010-01-03 17:44:40 +02:00
Jouni Malinen
9646a8ab8b Remove unnecessary wpa_event_type typedef 2010-01-03 13:10:12 +02:00
Jouni Malinen
fdbe50ed98 Fix CONFIG_AP=y build after driver API changes 2010-01-03 13:05:54 +02:00
Jouni Malinen
2a8b74163e Move struct hostapd_frame_info definition away from driver API
This is internal data structure for hostapd/AP functionality and does
not need to be defined in driver.h.
2010-01-03 12:37:02 +02:00
Jouni Malinen
245519e0cd Replace wpa_supplicant_sta_rx() call with driver event
Get rid of wpa_supplicant_sta_rx() and add a new driver event that is
marked to be used only with driver_test.c. In addition, remove this
functionality from privsep wrapper. This is only use for client mode
MLME testing with driver_test.c.
2010-01-03 11:50:26 +02:00
Jouni Malinen
8f770587d9 Maintain a pointer to the current BSS table entry 2010-01-02 16:59:19 +02:00
Jouni Malinen
a1fd2ce54e Do not store raw scan results
Use scan results to update the BSS table and to select the BSS for
connection, but do not store the results for longer time.
2010-01-02 16:41:38 +02:00
Jouni Malinen
6fa81a3b3f Use BSS table entry instead of raw scan result for connection 2010-01-02 16:16:02 +02:00
Jouni Malinen
8d923a4acf Only expire scanned BSSes based on new scan results
Get more information about scans when updating BSS table information.
This allows the missing-from-scans expiration rule to work properly
when only partial set of channels or SSIDs are being scanned.
2010-01-02 13:57:44 +02:00
Jouni Malinen
4832ecd754 Add an option for driver wrappers to report operational frequency 2009-12-28 13:23:13 +02:00
Jouni Malinen
f8b1f69561 Use generic driver events for TX status and RX reporting
Replace driver wrapper calls to hostapd_tx_status(),
hostapd_rx_from_unknown_sta(), hostapd_mgmt_rx(), and
hostapd_mgmt_tx_cb() with new generic driver events
EVENT_TX_STATUS, EVENT_RX_FROM_UNKNOWN, and EVENT_RX_MGMT.

This cleans up lot of the driver wrapper code to be less dependent
on whether it is being used within wpa_supplicant AP mode or hostapd.
2009-12-13 23:05:39 +02:00
Jouni Malinen
9c972abb66 IBSS RSN: Wait for connection event and do not use auth timeout
Wait for connection (IBSS join completed) event before marking state
completed. In addition, do not use the station mode authentication
timeout since that can trigger full disconnection from IBSS when
there is a timeout with just one of the peers.
2009-12-04 22:09:06 +02:00
Jouni Malinen
0e379654b0 SME: Do not process disassoc frame unless SME is used
This avoids an infinite loop with driver_test.c when using IBSS.
2009-12-04 21:44:13 +02:00
Jouni Malinen
a84ed99ee4 SME: Deauthenticate to clear state after disassociation events
cfg80211/mac80211 can get into somewhat confused state if the AP only
disassociates us and leaves us in authenticated state. For now, force
the state to be cleared with deauthentication to avoid confusing errors
if we try to associate with the AP again. This gets rid of 30 second
delay (scan timeout) in cases where only a disassociation frame is
received from the AP.
2009-12-02 17:26:28 +02:00
Jouni Malinen
3acb50056c Remove src/rsn_supp from default header path 2009-11-29 18:28:08 +02:00
Jouni Malinen
90973fb2fd Remove src/common from default header file path
This makes it clearer which files are including header from src/common.
Some of these cases should probably be cleaned up in the future not to
do that.

In addition, src/common/nl80211_copy.h and wireless_copy.h were moved
into src/drivers since they are only used by driver wrappers and do not
need to live in src/common.
2009-11-29 17:51:55 +02:00
Jouni Malinen
6ae9318536 Split scan processing for RSN preauthentication into parts
This avoids passing the raw scan results into the RSN code and by
doing so, removes the only dependency on src/drivers from the
src/rsn_supp code (or from any src subdirectory for that matter).
2009-11-29 17:06:03 +02:00
Jouni Malinen
62fa124ce2 nl80211/SME: Use reassociation when roaming within the ESS 2009-11-17 19:25:05 +02:00
Jouni Malinen
69856fadf7 Add wpa_msg_ctrl() for ctrl_interface-only messages
This is like wpa_msg(), but the output is directed only to
ctrl_interface listeners. In other words, the output will not be
shown on stdout or in syslog.

Change scan result reporting to use wpa_msg_ctrl() for
CTRL-EVENT-SCAN-RESULTS message at info level and wpa_printf() at
debug level to avoid showing scan result events in syslog in the
common configuration used with NetworkManager.
2009-11-10 15:59:41 +02:00
Jouni Malinen
e81634cd18 Skip networks without known SSID when selecting the BSS
Previously, APs that were hiding SSID (zero-length SSID IE in
Beacon frames) could have been selected when wildcard SSID matching
was used. This would result in failed association attempt since
the client does not know the correct SSID. This can slow down WPS
which is often using wildcard SSID matching.

Ignore BSSes without known SSID in the scan results when selecting
which BSS to use.
2009-10-15 21:58:58 +03:00
Sam Leffler
4f34d51abe Do not schedule a new scan if no networks are enabled
This avoids an extra timeout to move to INACTIVE state.
2009-10-14 22:05:58 +03:00
Jouni Malinen
6d6f4bb87f nl80211: Work around mac80211 limitation on (re)auth when authenticated
mac80211 does not currently allow (re)authentication when we are already
authenticated. In order to work around this, force deauthentication if
nl80211 authentication command fails with EALREADY. Unfortunately, the
workaround code in driver_nl80211.c alone is not enough since the
following disconnection event would clear wpa_supplicant authentication
state. To handle this, add some code to restore authentication state
when using userspace SME.

This workaround will hopefully become unnecessary in some point should
mac80211 start accepting new authentication requests even when in
authenticated state.
2009-10-12 09:39:55 +03:00