Commit graph

32 commits

Author SHA1 Message Date
Jouni Malinen
ad02e79d12 tests: Disable HT in ap_wds_sta_wep
HT cannot be used with WEP-only network, so don't try to do that here.
This get rids of some unnecessary Beacon frame updates during
disassociation/association and can make the test case a bit more robust.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-19 22:47:07 +02:00
Jouni Malinen
29bf636e12 tests: WEP to WPA2-PSK configuration change in hostapd
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-05 21:30:17 +02:00
Jouni Malinen
f0b6d1edfb tests: WDS 4addr behavior on reassociation and with open and WEP
This extends the ap_wds_sta test case to cover post-reassociation case
(both with and without Authentication frame exchange) and add similar
test cases to cover open and WEP cases in addition to this existing
WPA2-PSK test case.

These cover functionality testing for the previous fix in
reassociation-without-new-authentication case. In addition, these find a
new mac80211 issue for the WEP + 4addr combination.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-02 12:53:07 +02:00
Jouni Malinen
bacbb62294 tests: Beacon frame TX rate configuration
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-11-26 00:36:50 +02:00
Jonathan Afek
9fd6804d61 tests: Mark 525 tests as remote compatible
After successfully passing the 525 tests on a remote setup mark the
tests as remote compatible.

Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
2016-06-27 21:47:37 +03:00
Jonathan Afek
bb04a9a9a3 tests: Use general cmd_execute() for bridge setup commands
The hwsim tests used to execute shell commands in the tests using the
subprocess python module. Use the cmd_execute() general function for
executing shell commands to setup bridge so that this would also work on
remote setups.

Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
2016-06-27 21:47:37 +03:00
Jonathan Afek
a548c37bad tests: Use cmd_execute() for iw reg set 00
The hwsim tests used to execute shell commands in the tests using the
subprocess python module. Use the cmd_execute() general function for
executing "iw reg set 00" so that this would also work on remote setups.

Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
2016-06-27 21:10:35 +03:00
Jouni Malinen
49ae6ddbca tests: hostapd assocresp_elements
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-04-20 13:22:32 +03:00
Janusz Dziedzic
8b8a1864ff tests: Pass full apdev to add_ap() function (1)
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].

This step (1) converts the cases where apdev[#]['ifname'] was used as
the argument to hostapd.add_ap().

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2016-04-03 22:45:57 +03:00
Jouni Malinen
0215543103 tests: Information element parsing OOM
Signed-off-by: Jouni Malinen <j@w1.fi>
2016-03-26 22:53:58 +02:00
Jouni Malinen
4d2c287466 tests: Information element parsing - extra coverage
Signed-off-by: Jouni Malinen <j@w1.fi>
2016-03-26 22:53:58 +02:00
Jouni Malinen
542c68a688 tests: QCA vendor element parsing
Signed-off-by: Jouni Malinen <j@w1.fi>
2016-03-26 22:53:58 +02:00
Jouni Malinen
bc321e1597 tests: Make ap_max_num_sta_no_probe_resp more robust
It was possible for the AP's Beacon frame to be seen by dev[0] when
running a scan. This is not an error case. Make this test case more
robust by verifying with a sniffer whether a Probe Response frame was
sent to unexpected STA.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-12-06 13:38:18 +02:00
Jouni Malinen
dd0d294d2f tests: Maximum STA count and limit on Probe Response frames
This verifies hostapd behavior with no_probe_resp_if_max_sta=1.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-10-17 19:31:17 +03:00
Jouni Malinen
efe353d1aa tests: UPDATE_BEACON to change vendor_elements at runtime
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-05-24 13:43:30 +03:00
Jouni Malinen
c4668009d0 tests: Remove unnecessary use of sudo from test cases
run-tests.py is running as root, so sudo does not need to be used
anymore from within each test case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-07 15:37:13 +02:00
Jouni Malinen
9d7fdac5b3 tests: Try to clear scan results after regulatory domain changes
It was possible for regulatory domain changes to "leak" into following
test cases in number of cases where the cfg80211 BSS table remained
after regulatory domain had been restored to world roaming. Try to make
this less likely to occur by explicitly clearing BSS table at the end of
test cases that use different regulatory domain. This makes P2P test
cases that verify channel selection based on world roaming rules more
robust.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-15 01:32:01 +02:00
Jouni Malinen
1131a1c8d2 tests: Replace last remaining hwsim_test uses with DATA_TEST
External tool is not needed anymore to run the data connectivity tests
since hostapd test mode now allows the possible bridge or VLAN interface
to be specified.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 14:09:07 +02:00
Jouni Malinen
a8375c94c0 tests: Pass wpas/hapd instance to test_connectivity()
This makes it easier to replace data connectivity testing to use
something else than local hwsim_test binary on the controller device.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-19 17:54:49 +03:00
Jouni Malinen
7e49399b6f tests: Make ap_acl_accept and ap_acl_deny more robust
Use scan_for_bss() to make sure the AP is seen even under heavy CPU
load.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-15 18:38:11 +03:00
Jouni Malinen
6acecce1fe tests: hostapd configuration parameters
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-30 18:07:05 +03:00
Jouni Malinen
41be44afeb tests: max_num_sta limit
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-29 17:00:02 +02:00
Jouni Malinen
11a4c910ea tests: max_listen_interval rejecting association
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-29 16:56:14 +02:00
Jouni Malinen
a4e510fefd tests: Additional AP parameters
This tests basic rate, short preamble, and spectrum management
configuration.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-23 19:38:12 +02:00
Jouni Malinen
a424259a9b tests: AP using inactivity poll/disconnect
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-15 19:04:31 +02:00
Jouni Malinen
8a9a3b34dd tests: WDS STA mode
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-15 19:04:31 +02:00
Jouni Malinen
656a3ef276 tests: Static MAC ACL
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-13 23:27:11 +02:00
Jouni Malinen
f6e1eb07ee tests: Set country code and use 5 GHz band
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-10 10:49:49 +02:00
Jouni Malinen
52ec1aebe5 tests: hostapd adding vendor elements to Beacon/Probe Response frames
This verifies that the configuration parameter vendor_elements works
correctly.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-10 10:42:41 +02:00
Jouni Malinen
56d3b4d668 tests: Enable CCMP fragmentation check
This was triggering failures due to a mac80211 bug that has now been
fixed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-24 17:15:16 +02:00
Jouni Malinen
5be9dcbb86 tests: Remove unnecessary interpreter line from most python files
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-02-21 20:21:53 +02:00
Jouni Malinen
e769364b82 tests: Add test cases for various AP mode parameters
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-04 13:10:57 +02:00