The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.
This command makes a virtual mesh interface to be used for mesh gate.
This command expects to be used like this.
wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Since mesh functionality uses struct hostapd_data to maintain peer
state, the existing STA* control interface commands can be used to
display information about the peers.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was used only for the VHT capability checks for determining bit
offset for right shift. That was replaced with a constant defines since
there is no need to calculate this at runtime.
Signed-off-by: Jouni Malinen <j@w1.fi>
Option '-p' of 'read' command may be unsupported in some POSIX-complete
shells. So replace 'read -p' with 'echo -n'/'read' pair.
Signed-off-by: Oleksandr Chumachenko <ledest@gmail.com>
Building wpa_supplicant with the musl C library fails since musl does
not define type names such as '__uint32_t'. To support building
wpa_supplicant with the musl C library use the integer types declared in
the ISO C standard header file <stdint.h>.
Signed-off-by: Jörg Krause <jkrause@posteo.de>
drv->ctx always points to the first BSS and we should report event using
BSS related to the interface we got NL80211_CMD_NEW_STATION from.
This fixes STA association for drivers using NL80211_CMD_NEW_STATION and
multiple virtual interfaces.
Before:
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0-1 (ifindex:7)
nl80211: New station 02:00:00:00:01:00
wlan0: STA 02:00:00:00:01:00 IEEE 802.11: associated
After:
nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION) received for wlan0-1 (ifindex:7)
nl80211: New station 02:00:00:00:01:00
wlan0-1: STA 02:00:00:00:01:00 IEEE 802.11: associated
This is not applicable to the cases where authentication (AP SME & MLME)
is in hostapd and hostapd_assoc_cb() instead of hostapd_notif_assoc()
handles BSS selection.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
If tray icon messages are perceived as disturbing, one can pass `-q`
parameter on the command line to disable them permanently.
Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
Show associated network SSID in the tool tip message of the
application's tray icon. When network is not associated, then simple
"(not-associated)" message is shown.
Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
Instead of just stopping connection process and network discovery,
report SAE failures to build Authentication frames (e.g., due to missing
password) as a connection failure to get the normal retry mechanism into
use.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows recovery through fallback to full EAP authentication if the
server rejects us, e.g., due to having dropped ERP state.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to drop any pending ERP key from both the internal AP
authentication server and RADIUS server use of hostapd.
Signed-off-by: Jouni Malinen <j@w1.fi>
This ends up using the special offchannel.c code path where a different
interface is selected for TX. In addition, the P2P-PRESENCE-RESPONSE
event is verified to be delivered on the group interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
Both the wpa_s->pending_action_src and src argument to
wpas_get_tx_interface() were used somewhat randomly. Make this more
consistent since these values are pointing to the same address and the
implementation is easier to understand when it is obvious that there is
only one address being used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The results for these are not currently verified, but this allows
--codecov runs to get more coverage for the command line argument
parsers.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids one more cleanup step between most test cases by clearing
the default PMF behavior change only in case it was actually modified
during a test.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids one more cleanup step between most test cases by stopping ER
only in case it was actually used during a test.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function could not fail and it can be replaced with a single
line variable update that takes less code than the function call.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_bss_flush*() cannot fail and as such, there is no need for
wpa_supplicant_ctrl_iface_bss_flush() to return a value either.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function cannot return negative value, so no need to check for
that. If there is not enough room in the buffer or if something
unexpected happens, 0 is returned.
Signed-off-by: Jouni Malinen <j@w1.fi>
This uses a new testing mode in hostapd to allow RRM neighbor request
transmittion to be tested. For the second part of the test case to be
executed, mac80211_hwsim needs to be modified to claim support for the
required RRM capabilities (that change is not yet in Linux kernel).
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf radio_measurements parameter can now be used to
configure a test build to advertise support for radio measurements with
neighbor report enabled. There is no real functionality that would
actually process the request, i.e., this only for the purpose of minimal
STA side testing for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, only WPA + WPA2 was covered. If FT is enabled in addition to
WPA, MDIE is included in the buffer between RSN and WPA elements. The
previous version ended up leaving only the MDIE after having skipped RSN
element. Fix this to skip MDIE as well to leave only WPA IE regardless
of whether FT is enabled in AP configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
