Passing a pointer to an error reply message is not very robust since
memory allocation could fail even for that error message. Instead, use a
separate error value as the return value from get_peer_hwaddr_helper()
and return a pointer to the error message through a pointer-to-pointer
so that the error case will always be clear.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to use a for loop here since the h variable is
set identically at the beginning of the body anyway.
Signed-off-by: Jouni Malinen <j@w1.fi>
The following if statements set the new_op_mode value in all cases,
so there is no need to initialize this to 0 first. This removes a
static analyzer warning.
Signed-off-by: Jouni Malinen <j@w1.fi>
The pos variable was not used between its first and second assignment.
Clean this up by using the pos variables instead of the buf (start of
the buffer).
Signed-off-by: Jouni Malinen <j@w1.fi>
The pos pointer can be compared to the start of the buffer pointer to
determine whether the entry is the first one in the list. This gets rid
of some static analyzer warnings about unused variable writes.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to maintain a separate counter for this in addition to
the pointer to the current location. In addition, this gets rid of
warnings about unused variable write.
Signed-off-by: Jouni Malinen <j@w1.fi>
The group name is not used on these paths, so just remove it from the
directory name without updating gid_str to point to the unused group
name.
Signed-off-by: Jouni Malinen <j@w1.fi>
If hapd_iface->bss[i] == NULL, this could have resulted in NULL pointer
dereference in the debug print. Avoid this by skipping the message in
case of NULL pointer. In addition, clear iface->bss[i] to NULL for
additional robustness even though this array gets freed immediately.
Signed-off-by: Jouni Malinen <j@w1.fi>
The scan result comparison routine would not make much sense without
current BSS level known, so return from the function without going
through the iteration that could have dereferenced the pointer if
wpa_s->current_bss == NULL.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was previously checked through the eap_peer_tls_ssl_init() call
which made it difficult for static analyzers. Add an explicit check for
config == NULL into the beginnign of eap_fast_init() since this will
always result in initialization failing anyway.
Signed-off-by: Jouni Malinen <j@w1.fi>
If wpa_driver_roboswitch_read() fails before such comparison, the values
that are being compared are not initialized properly and as such, there
is not much point in comparing them either.
Signed-off-by: Jouni Malinen <j@w1.fi>
This seemed to be fine on most code paths, but the code was complex
enough to make the analysis difficult (and a bit too much for static
analyzers). There is no harm in forcing these parameters to be
initialized, so do that to make sure they cannot be left uninitialized.
Signed-off-by: Jouni Malinen <j@w1.fi>
bfd_demangle() call could be skipped if data.function == NULL. Make sure
the already freed aname pointer cannot be used again in such a case.
Signed-off-by: Jouni Malinen <j@w1.fi>
record->type == NULL case was handled through the record->type_length
comparison. While this was correct, it is a bit difficult for static
analyzers to understand, so add an extra check for NULL to avoid false
reports on this.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is the older design that some drivers may still use if they do not
support offloaded offchannel TX operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
no_offchannel_tx=1 driver parameter can now be used to force the older
remain-on-channel -based offchannel TX design to be used with
mac80211_hwsim. This can be used to increase test coverage with the
hwsim test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
A bit different code path is used to match the first three different
locations of roaming consortium OI within Beacon frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the error path to try to use P2P Group ID attribute
even if one was not included in the message. This could result in
dereferencing a NULL pointer, so re-check the pointer before copying the
data.
Signed-off-by: Jouni Malinen <j@w1.fi>
The special case of non-zero status code used in a GAS Comeback Response
frame to indicate that additional delay is needed before the response is
available was not working properly. This case needs to allow the status
code check to be bypassed for the comeback case prior to having received
any response data.
Signed-off-by: Jouni Malinen <j@w1.fi>
The simulated SIM/USIM case uses a separate milenage cred parameter, so
this cred password parameter was unused for this credential type.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like leaving behind the freed pointed at the end of the array
could end up in a crash triggered by double free in some cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commits 7ef6947993 and
533536d82a added this temporarily
disabling case, but those commits were merged in without having been
converted to the new os_reltime design used for ssid->disabled_until.
Consequently, they ended up disabling the network for 44 years or so too
long time (depending on what values the relative timestamp had
accummulated so far). Fix this by using relative timestamps
consistently.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Wait a bit between WPS_CONFIG command and the first scan. This can avoid
an extra five second wait due to having to scan again if the initial
scan operations happens to be quick enough to happen before the AP has
updated its configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
PD Response is sent out using a 200 ms offchannel wait, but that wait
was not cancelled on TX status report. This could result in offchannel
operation being left waiting unnecessarily long. Fix this by making the
P2P_NO_PENDING_ACTION case in Action TX callback cancel the wait if a
pending wait is marked (and mark this for PD Response).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like some deployed devices may send an invalid supported
operating class element (length = 0) in TDLS Setup messages. With
cfg80211, this results in the NL80211_CMD_SET_STATION command failing
due to an invalid argument (cfg80211 mandates supported operating
classes information to have a length of 2..253 octets).
Work around this interop issue by ignoring the Supported Operating Class
element if it has invalid length.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that 'INTERWORKING_SELECT auto' is able to pick the
correct network based on priority configuration when connected to a
lower priority network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
