Return control flow to hostapd by calling hostapd_acs_completed()
if requesting a scan from the underlying device fails.
Signed-hostapd: Helmut Schaa <helmut.schaa@googlemail.com>
If radar was detected single BSS is notified about it. This caused only
that single BSS to be stopped and restarted. However, due to nl80211
interface combinations the BSS was not started on a new channel and
other BSSes remained operating on the old channel.
The downside is that hostapd_disable_iface() causes deauth frames to be
sent. This is undesired but on the other hand it doesn't make sense to
create workarounds that imitate CSA's 'block tx'. For proper Tx
quiescing CSA should be properly implemented.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Decouple HT/VHT offset/center-freq calculations from channel lookup.
This will be necessary for further improvements on the DFS codebase.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Reject RELOAD control interface command if the dynamic configuration
changes have resulted into a state where the configuration is invalid.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the configuration validation routines to be called from
src/ap/*.c for runtime updates of configuration without reprocessing the
full configuration file.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This provides a new option for configuring multiple virtual interfaces
(BSS) that share a single radio. The new command line parameter
-b<phyname>:<config file name> is used to define one or more virtual
interfaces for each PHY. The first such entry for a new PHY is used to
initialize the interface structure and all consecutive parameters that
have the same PHY name will be added as virtual BSS entries to that
interface. The radio parameters in the configuration files have to be
identical.
This can be used as an alternative for the bss=<ifname> separator and
multiple BSSes in a single configuration file design while still
allowing hostapd to control the PHY (struct hostapd_iface) as a group of
virtual interfaces (struct hostapd_data) so that common radio operations
like OLBC detection and HT40 co-ex scans can be done only once per real
radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it more convenient to move BSS configuration entries between
struct hostapd_config instances to clean up per-BSS configuration file
design.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This may be needed if the wpa_psk information for previously derived
from passphrase and either the SSID or the passphrase has changed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of duplicating the functionality and missing changes (like the
hostapd_broadcast_wep_clear() call), use the hostapd_clear_old()
function that was already used for the similar case with configuration
file reload.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Mask the remote VHT capabilities with our own capabilities, similarly
to what is done for HT capabilities.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Make sure the driver supports 160/80+80 MHz VHT capabilities
before trying to configure these channels.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
When we have CAC active and receive a radar event, we should ignore
CAC_ABORT event and handle channel switch in the radar event handler.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This fixes a problem when operating on non-DFS channel and receiving a
radar event for that channel. Previously, we would have decided to
switch channels.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add a table of available VHT80 channels. This table contains the first
available channel. We will also choose this first channel as the control
one.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Some driver wrappers may implement this by writing eight octets even
though IPN is only six octets. Use a separate WPA_KEY_RSC_LEN (8) octet
buffer in the call to make sure there is enough buffer room available
for the full returned value and then copy it to IPN field.
The previous implementation used the following igtk field as the extra
buffer and then initialized that field afterwards, so this change does
not fix any real issue in behavior, but it is cleaner to use an explicit
buffer of the maximum length for get_seqnum().
Signed-hostap: Jouni Malinen <j@w1.fi>
The VHT_CHANWIDTH_160MHZ case fell through to the default case and
printed out a debug message that was not supposed to be shown here.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously ACS required valid survey data on all available channels.
This can however not be guaranteed. Instead of just failing, fall back
to the subset of channels that have valid ACS data.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
Otherwise hostapd might hang doing nothing anymore. Propagate ACS
errors so we can fail gracefully.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
If ACS fails we still need to call hostapd_setup_interface_complete.
Otherwise hostapd will just hang doing nothing anymore. However, pass
an error to hostapd_setup_interface_complete to allow a graceful fail.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
The new bss_load_test parameter can be used to configure hostapd to
advertise a fixed BSS Load element in Beacon and Probe Response frames
for testing purposes. This functionality is disabled in the build by
default and can be enabled with CONFIG_TESTING_OPTIONS=y.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows QoS Map Set element to be added to (Re)Association Response
frames and in QoS Map Configure frame. The QoS Mapping parameters are
also made available for the driver interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add DFS structures/events handlers, CAC handling, and radar detection.
By default, after radar is detected or the channel became unavailable, a
random channel will be chosen.
This patches are based on the original work by Boris Presman and
Victor Goldenshtein. Most of the DFS code is moved to a new dfs.c/dfs.h
files.
Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
When hostapd receives an auth frame during ACS the transmission of
the according auth response will always fail:
ACS: Automatic channel selection started, this may take a bit
[..]
send_auth_reply: send: Resource temporarily unavailable
[..]
However, a station info entry was created. Once ACS is finished
it will flush all stations even though hapd was not yet fully
initialized. This results in a segfault when trying to access
hapd->radius:
0 0x0042c1c0 in radius_client_flush_auth ()
1 0x00416a94 in ap_free_sta ()
2 0x00416cc0 in hostapd_free_stas ()
3 0x0040bce8 in hostapd_flush_old_stations ()
4 0x0040c790 in hostapd_setup_interface_complete ()
5 0x0046347c in acs_scan_complete ()
6 0x0040f834 in hostapd_wpa_event ()
7 0x0043af08 in send_scan_event.part.46 ()
8 0x00443a64 in send_scan_event ()
9 0x00443c24 in do_process_drv_event ()
10 0x004449e8 in process_global_event ()
11 0x7767d7d0 in ?? ()
Fix this by not presuming anything about the initialization state of
hapd and checking ->radius before accessing.
Signed-off-hostapd: Helmut Schaa <helmut.schaa@googlemail.com>
There is no need to use the bss variable which is used only within a
wpa_printf() call that can be conditionally removed from the build.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This extends hostapd global control interface command "ADD" to use a
configuration file instead of requiring configuration to be built using
SET command.
The command format is now following:
ADD <ifname> <control path|config=<path to config>>
For example:
ADD wlan0 /var/run/hostapd
ADD wlan0 config=/tmp/hostapd.conf
When using the configuration file option, ctrl_interface parameter in
the file needs to be set to allow ENABLE command to be issued on the new
interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There was a comment about the the cleanup steps being from
hostapd_cleanup_iface(). However, the operations that cleared some
security parameters do not seem to exist elsewhere and do not make sense
here. Remove them to avoid changing configuration with DISABLE followed
by ENABLE.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes some issues where dynamic interface enable/disable cycles
could end up trying to free resources twice and crash the process while
doing so.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new control interface command P2P_REMOVE_CLIENT <P2P Device
Address|iface=Address> can now be used to remove the specified client
from all groups (ongoing and persistent) in which the local device is a
GO. This will remove any per-client PSK entries and deauthenticate the
device.
Signed-hostap: Jouni Malinen <j@w1.fi>
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
When using per-device PSKs, select the PSK based on the P2P Device
Address of the connecting client if that client is a P2P Device. This
allows the P2P Interface Address to be changed between P2P group
connections which may happen especially when using persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to implement per-device PSK selection based on the
peer's P2P Device Address instead of P2P Interface Address.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes the P2P Device Address of the Enrollee available with the PSK
records to allow P2P Device Address instead of P2P Interface Address to
be used for finding the correct PSK.
Signed-hostap: Jouni Malinen <j@w1.fi>
"wpa_cli p2p_set per_sta_psk <0/1>" can now be used to disable/enable
use of per-device PSKs in P2P groups. This is disabled by default.
When enabled, a default passphrase is still generated by the GO for
legacy stations, but all P2P and non-P2P devices using WPS will get
a unique PSK.
This gives more protection for the P2P group by preventing clients from
being able to derive the unicast keys used by other clients. This is
also a step towards allowing specific clients to be removed from a group
reliably without having to tear down the full group to do so.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds ACS support to hostapd. Currently only survey-based
algorithm is available.
To use ACS you need to enable CONFIG_ACS=y in .config and use
channel=0 (or channel=acs_survey) in hostapd.conf.
For more details see wiki page [1] or comments in src/ap/acs.c.
[1]: http://wireless.kernel.org/en/users/Documentation/acs
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
This adds survey dump support for all frequencies
and for specific desired frequencies. This will later
be used by ACS code for spectrum heuristics.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
This splits up the channel checking upon initialization into a few
helpers. This should make this a bit easier to follow. This also paves
the way for some initial ACS entry code.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
According to WSC specification (Ver 2.0.2, section 8.3), RF Bands
attribute should be set to the specific RF band used for the current
message. Add an option to set wanted band in wps_build_rf_bands() and
add a callback to get the current band from wpa_supplicant and hostapd.
Signed-hostap: David Spinadel <david.spinadel@intel.com>
The pad field in the RRB messages is unused, but it should be
initialized to avoid sending out arbitrary data from stack. This was
also generating number of valgrind complaints about uninitialized memory
accesses in local FT tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
The static WEP keys have to be configured for the new VLAN
interface that is created for a 4addr WDS peer, not doing so
breaks WEP functionality in nl80211/4addr based WDS links.
Signed-hostap: Sujith Manoharan <c_manoha@qca.qualcomm.com>
In a AP/STA concurrent setup, if the STA interface is continually
scanning, trying to connect to a network, the AP interface
is basically broken since beaconing would be erratic.
This option can be used in a WDS setup where one AP acts as a
Client/AP-Repeater. The Repeater AP interface has to start beaconing
only after the Client interface has established a WDS link with the
"Root AP".
Signed-hostap: Sujith Manoharan <c_manoha@qca.qualcomm.com>
The new server_id parameter in hostapd.conf can now be used to specify
which identity is delivered to the EAP peer with EAP methods that
support authenticated server identity.
Signed-hostap: Jouni Malinen <j@w1.fi>
When using OpenSSL with TLS-based EAP methods, wpa_supplicant can now be
configured to use OCSP stapling (TLS certificate status request) with
ocsp=1 network block parameter. ocsp=2 can be used to require valid OCSP
response before connection is allowed to continue.
hostapd as EAP server can be configured to return cached OCSP response
using the new ocsp_stapling_response parameter and an external mechanism
for updating the response data (e.g., "openssl ocsp ..." command).
This allows wpa_supplicant to verify that the server certificate has not
been revoked as part of the EAP-TLS/PEAP/TTLS/FAST handshake before
actual data connection has been established (i.e., when a CRL could not
be fetched even if a distribution point were specified).
Signed-hostap: Jouni Malinen <j@w1.fi>
Currently, hostapd_get_vlan_id_ifname() is used to determine if a given
vlan is valid *and* to actually determine the interface. This leads to
wpa_set_keys() sometimes setting the key on the wildcard interface name,
which does not make sense.
This patch therefore adds hostapd_vlan_id_valid() and makes
hostapd_get_vlan_id_ifname() not return a wildcard interface.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Currently, struct hostapd_vlan is a per-BSS data structure which
also contains informations about whether to remove the bridge
or clear wlan / tagged-vlan interface from the bridge.
In a multi-interface multi-BSS setup, this can lead to the following
race condition:
1. wlan0 creates VLAN A, sets DVLAN_CLEAN_BR and DVLAN_CLEAN_VLAN_PORT
2. wlan1 creates VLAN A, does not set DVLAN_CLEAN_BR and
DVLAN_CLEAN_VLAN_PORT as already there
3. wlan0 removes VLAN A, removes tagged-interface from the bridge
but not the bridge.
Now wlan1 VLAN A is unusable due to the missing uplink.
4. wlan1 removes VLAN A, does not cleanup
Solution:
This requires an inter-BSS inter-interface data structure to track the
bridge / bridge port usage within hostapd. This data structure could
also be used to track any other device-has-been-created-by-hostapd
information or when regarding interface freeing.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Currently by default, all BSS share the bridge brvlan%d.
While this is sane when no tagged-interface is given, this
is insane when different tagged interfaces are given, as
it would result in bridging those tagged interfaces.
This patch therefore uses br%s%d with %s=tagged_interface
and %d=VLAN ID as bridge name when a tagged-interface is given.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Currently, when different BSS using different tagged vlan
interfaces, they are forced to share the bridge brvlan#,
which is not desirable.
This patch fixes this by making the bridge name configurable.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
If AP mode SME/MLME within wpa_supplicant is used for processing Probe
Request frames in GO mode, drop Probe Request frames that include only
802.11b rates per P2P spec section 2.4.1.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Upon association, disable the timer that removes the dummy STA. This
timer caused the STA that associates within 5 seconds of doing an ANQP
query to disassociate, thinking it's a dummy STA. Similar call was
already there for the SME/MLME-in-hostapd case in handle_auth(), but the
SME-in-driver case was not previously addressed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up debug log by not including comments about failed
operations in case the operation is known to fail due to not being
supported by the driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Enable MAC address based ACL for the drivers which advertise
this capabilty with NL80211_ATTR_MAC_ACL_MAX. Either of blacklist
or whitelist is supported, though, not simultaneously.
Signed-hostap: Vivek Natarajan <nataraja@qca.qualcomm.com>
This is needed to avoid allowing the STA to reconnect using a cached
PMKSA. ESS disassoc imminent notification is normally used to indicate
that the STA session will be terminated and as such, requiring full
authentication through the authentication server after this is needed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The hostapd_cli ess_disassoc command now takes three arguments (STA MAC
address, timeout in ms, URL) and the STA is disconnected after the
specified timeout.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These events are sent as a special case to both the group interface and
"parent interface" (i.e., the interface that was used for managing P2P
negotiation). The latter is not really correct event, so get rid of it
with the new global control interface design where there is no need to
support legacy upper layer implementations.
Signed-hostap: Jouni Malinen <j@w1.fi>
This patch is based on the original work by Boris Presman and
Victor Goldenshtein. Channel Switch Announcement support has been
removed and event handling as well as channel set handling was
changed, among various other changes.
Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Since "pairwise" is defined as an integer, the current assignment leads
to it having the value 0 or 8, which is a bit strange in debug output:
WPA: Send EAPOL(version=2 secure=1 mic=1 ack=1 install=1 pairwise=8
kde_len=46 keyidx=2 encr=1)
Use !!(...) to normalize it to 0 or 1.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
For some testing it can be useful to force the Key MIC in group
EAPOL-Key frames to be corrupt. Add an option to allow setting a
probability for corrupting the Key MIC and use it in the WPA code,
increasing the first byte of the MIC by one to corrupt it if desired.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
There are quite a few places in the current implementation where a nul
terminated string is generated from binary data. Add a helper function
to simplify the code a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
My APs generate their configuration on their own using a different
number of (vlan-enabled) bss. Currently, all my vlan_file files consist
of a single line: the wildcard line. Configuration file generation would
be easier, if the hostapd configuration file would not depend on those
simple vlan_file files.
This patch removes the need for those one-line files by using the
<device>.<vlan> naming scheme if no vlan_file is given (or that file is
empty). This should not break any existing setup, as using dynamic_vlan
with no vlan configured does not make sense anyway.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
In order to test clients in scenarios where APs may (randomly)
drop certain management frames, introduce some testing options
into the hostapd configuration that can make it ignore certain
frames. For now, these are probe requests, authentication and
(re)association frames.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Some extended capabilities (I'm currently interested in "Operating Mode
Notification" for VHT) are implemented by the kernel driver and exported
in nl80211. Use these in hostapd/wpa_supplicant.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The new wps_independent=1 configuration parameter can be used to remove
interfaces from the shared hostapd process WPS control (i.e., to apply
WPS operations only to a subset of interfaces instead of all).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows WPS to update AP configuration in the case no hostapd
configuration file is used (i.e., dynamic configuration through the
control interface).
Signed-hostap: Jouni Malinen <j@w1.fi>
When the OS is out of random bytes in SM_STATE(WPA_PTK, AUTHENTICATION2)
in ap/wpa_auth.c, hostapd sends the sm to state DISCONNECT without
clearing ReAuthenticationRequest, resulting in an infinite loop.
Clearing sm->ReAuthenticationRequest using gdb fixes the running hostapd
instance for me. Also sm->Disconnect = TRUE should be used instead of
wpa_sta_disconnect() to make sure that the incomplete ANonce does not
get used.
Fix this issue by resetting sm->ReAuthenticationRequest even if the STA
gets disconnected and use sm->Disconnect instead of
wpa_sta_disconnect().
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
A non-HT capable AP on any channel could have triggered us to enable
protection regardless of own operating channel if the driver delivered
Beacon frames from other channels. The channel detection in ap_list is
not exactly ideal, but most cases can be handled by checking ap->channel
against the currently configured channel (or secondary channel in case
of HT40).
Signed-hostap: Jouni Malinen <j@w1.fi>
This iter_next/iter_prev pointers were not really used for anything, so
get rid of the unnecessary complexity in the AP list maintenance.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new -G<group> command line argument can now be used to set the group
for the control interfaces to enable cases where hostapd is used without
a configuration file and the controlling program is not running with
root user privileges.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit b52f084cfa introduced a mechanism
for adding arbitrary vendor-specific elements into the Beacon and Probe
Response frames. However, this information was not added to the separate
buffers used for specifying Beacon and Probe Response IEs for drivers
that build the frames internally. Add vendor_elements to these values,
too, to support such drivers in addition to drivers that use the full
Beacon tail/head buffers.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Clear WLAN_STA_ASSOC_REQ_OK, otherwise no Class 3 frame will be sent to
the disconnected STA in response to data frames.
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
The VHT IE struct just has an opaque 8-byte array for the MCS
set, make it more expressive by explicitly naming the pieces.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
WSC specification 2.0 section 7.4 describes OOB password to be expressed
in ASCII format (upper case hexdump) instead of raw binary.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 2d9ffe1e85 broke GAS server
callback for receiving Public Action frames. The incorrect context
pointer was used in the public_action_cb2 case. Fix this to use the
correct context pointer.
Signed-hostap: Jouni Malinen <j@w1.fi>
"WPS_NFC_TOKEN <WPS/NDEF>" used to generate a new NFC password token
regardless of whether there was a pre-configured token in the
configuration. Change this to use the pre-configured value, if
available, instead. This allows the same command to be used to write the
password token to an NFC tag more conveniently.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Control interface command "NFC_GET_HANDOVER_SEL NDEF WPS-CR" can now be
used to fetch WPS carrier record from hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
The capability itself isn't really affected by an OBSS
scan, only the HT operation must then be restricted to
20 MHz. Change this, and therefore use the secondary
channel configuration to determine the setting of the
OP_MODE_20MHZ_HT_STA_ASSOCED flag.
This shouldn't really change anything functionally,
it just makes the code a little less confusing and
is also needed to implement more dynamic bandwidth
changes if ever desired.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
When AP mode operation reject the client, nl80211 layer advertises the
connect failed event with the reason for failures (for example, max
client reached, etc.) using NL80211_CMD_CONN_FAILED.
This patch adds some debug messages whenever such an event is received
from the nl80211 layer and also the same event is posted to the upper
layer via wpa_msg().
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
GAS server used the same public_action_cb mechanism as P2P to process
Action frames. This ended up overriding P2P processing of Action frames
while running an AP/GO interface with a build that enables Interworking
(e.g., for Hotspot 2.0) and a driver that uses hostapd for AP mode
SME/MLME. Fix this by adding a separate callback registration for the
GAS server. This should really be cleaned up by supporting arbitrary
number of callback handlers, but for now, this addresses the regression
with a minimal change.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Most of the variables are not needed anymore once the SAE instance
has entered Accepted state. Free these to save memory.
Signed-hostap: Jouni Malinen <j@w1.fi>
The optional "reason=<reason code>" parameter to the ctrl_iface
deauthenticate and disassociate commands can now be used to change the
reason code used in the disconnection frame. This can be used, e.g., by
P2P GO to disconnect a single P2P client from the group by sending it an
indication of the group getting terminated (Deauthentication frame with
reason code 3). It needs to be noted that the peer device is still in
possession on the PSK, so it can still reconnect to the group after this
if it does not follow the group termination indication.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use of two variables to track bounds checking seems to be a bit too much
for some static analyzers, so add an extra condition for buffer padding
to avoid incorrect warnings.
Signed-hostap: Jouni Malinen <j@w1.fi>
The code initializing GMK Counter uses the group pointer value as extra
entropy and to distinguish different group instances. Some static
analyzers complain about the sizeof(pointer) with memcpy, so use a more
explicit type casting to make it more obvious what the code is doing.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd.conf sae_groups parameter can now be used to limit the set of
groups that the AP allows for SAE. Similarly, sae_groups parameter is
wpa_supplicant.conf can be used to set the preferred order of groups. By
default, all implemented groups are enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd can now be configured to use anti-clogging mechanism based on
the new sae_anti_clogging_threshold parameter (which is
dot11RSNASAEAntiCloggingThreshold in the standard). The token is
generated using a temporary key and the peer station's MAC address.
wpa_supplicant will re-try SAE authentication with the token included if
commit message is rejected with a token request.
Signed-hostap: Jouni Malinen <j@w1.fi>
The enum values for struct sae_data::state now match the protocol
instance states as defined in IEEE Std 802.11-2012, 11.3.8.2.2
Signed-hostap: Jouni Malinen <j@w1.fi>
The PMKSA cache expiration timer was not actually ever initialized since
the only place for registering the timeout was in the timeout handler.
Fix this by initializing the timer whenever a new PMKSA cache entry is
added to the beginning of the list (i.e., when it was the first entry or
expires before the entry that was previously going to expire first).
[Bug 393]
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 4378fc14eb started using QoS Data
frames for QoS STAs. It used the correct flags value for WPA/RSN
EAPOL-Key frames, but wrong flags for IEEE 802.1X EAPOL frames. The
WPA_STA_WMM value used in driver_nl80211.c happens to be identical to
WLAN_STA_ASSOC in sta->flags and this makes driver_nl80211.c try to use
QoS header for all STAs. Fix this by properly converting the flags from
WLAN_STA_* to WPA_STA_*. [Bug 426]
Signed-hostap: Jouni Malinen <j@w1.fi>
Add some more functionality for BSS Transition Management:
- advertise support for BSS Transition Management in extended
capabilities element
- add hostapd.conf parameter bss_transition=1 for enabling support
for BSS Transition Management
- add "hostapd_cli disassoc_imminent <STA> <num TBTTs>" for sending
disassociation imminent notifications for testing purposes
- wpa_supplicant: trigger a new scan to find another BSS if the
current AP indicates disassociation imminent (TODO: the old AP needs
to be marked to use lower priority to avoid re-selecting it)
Signed-hostap: Jouni Malinen <j@w1.fi>
This optional attribute may make it easier to bind together the
Access-Request and Accounting-Request messages. The accounting session
identifier is now generated when the STA associates instead of waiting
for the actual session to start after successfull authentication.
Signed-hostap: Jouni Malinen <j@w1.fi>
Basic support for the 60 GHz band. Neither P2P nor WPS are yet taken
care off. Allows to start AP with very simple config:
network={
ssid="test"
mode=2
frequency=60480
key_mgmt=NONE
}
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The config says that the default for ap_table_max_size is 255 and the
default for ap_table_expiration_time is 60. But the code doesn't reflect
the default values mentioned in the sample config file.
These variables completely disable the code for Overlapping Legacy BSS
Condition by default when they are not correctly initialized. WFA
certification requires this feature and therefore an AP would have
failed the certification process unless they were initialized manually
using the configuration file.
Signed-hostap: Sven Eckelmann <sven@open-mesh.com>
Signed-hostap: Simon Wunderlich <simon@open-mesh.com>
If separate hostapd processes are used for different RF bands, the
dualband parameter for WPS was not set correctly. Allow dualband
indication (mainly, addition of RF bands attribute for PBC session
overlap detection) also based on wps_rf_bands value (if set to "ag").
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows Probe Request frame processing to compare the configured
SSID to the SSID List element in addition to the SSID element.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. Previously it was possible to
define CONFIG_IEEE80211V without CONFIG_WNM which would break the build.
In addition, IEEE 802.11v has been merged into IEEE Std 802.11-2012 and
WNM is a better term to use for this new functionality anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
pmksa_cache_free_entry() takes care of updated the list head pointer
(pmksa->pmksa), so no need to do this change in the caller.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use the shared_secret pointer from RADIUS client implementation instead
of getting this from hostapd configuration data.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds support for multiple PSKs per station when using a RADIUS
authentication server to fetch the PSKs during MAC address
authentication step. This can be useful if multiple users share a
device but each user has his or her own private passphrase.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Add the configuration option vht_oper_centr_freq_seg1_idx
for the second segment of an 80+80 MHz channel and use it
when building the VHT operation IE.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This allows the AP to figure out whether a station is a HS 2.0 STA
during the association and access any information that the STA may have
included in this element.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
CONFIG_SQLITE=y option can now be used to allow the eap_user_file text
file to be replaced with a SQLite database
(eap_user_file=sqlite:/path/to/sqlite.db). hostapd.eap_user_sqlite
shows an example of how the database tables can be created for this
purpose. This commit does not yet include full functionality of the
text file format, but at least basic EAP-TTLS/MSCHAPv2 style
authentication mechanisms with plaintext passwords can be used for
tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
