Commit graph

110 commits

Author SHA1 Message Date
Johannes Berg
b3493fa110 AP: Use monotonic time for STA connected time
Connected time is relative, so should be using monotonic time
rather than time of day.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-07 20:50:14 -08:00
Mohammed Shafi Shajakhan
336167c80e AP: Fix inactivity STA timer trigger for driver offload case
Some non-mac80211 drivers, such as ath6kl, support STA inactivity timer
in firmware and may not provide connected stations' idle time to the
userspace. If the driver indicates support for offloaded operation, do
not start the inactivity timer in the hostapd.

Signed-hostap: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
2013-11-24 12:01:55 +02:00
Janusz Dziedzic
80ed037f00 Clear beacon_data before usage
struct beacon_data contains a lot of pointers. Make sure it gets cleared
to zero if hostapd_build_beacon_data() gets called from a path that does
not clear the structure first.

Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2013-11-22 23:21:43 +02:00
Michal Kazior
68d628accd hostapd: Fix interface enabling/disabling and DFS
The 'started' state was tracked incorrectly. It also broke DFS
as it was using hostapd_enable/disable_iface() functions.

Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
2013-11-20 22:29:35 +02:00
Andrei Otcheretianski
bf281c129f Add AP channel switch mechanism
Build CSA settings and call the driver to perform the switch. Construct
Beacon, Probe Response, and (Re)Association Response frames both for CSA
period and for the new channel. These frames are built based on the
current configuration. Add CSA IE in Beacon and Probe Response frames.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2013-11-17 17:12:58 +02:00
Abhishek Singh
795baf773f hostapd: Filter channel list updated events after country code change
We were not filtering the EVENT_CHANNEL_LIST_CHANGED events based on the
regulatory hint initiator. So wait for EVENT_CHANNEL_LIST_CHANGED event
after our own change was triggered even when regulatory hint initiator
was the driver. This could result in the wait for the channel list to be
updated to be terminated before the real change has occurred and as
such, old channel list remaining in use when configuring
hostapd/wpa_supplicant country parameter. Fix this by filtering the
hints according to the initiator and only regulatory hints initiated by
user will be used to stop the wait.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-15 02:59:55 +02:00
Jouni Malinen
5e1a4565f8 hostapd: Do not start secondary BSS unless interface is enabled
It is possible for additional BSSs to be added while the primary
interface is still in the process of determining channel parameters (HT
co-ex scan, ACS, DFS). Do not enable secondary interfaces in such state
immediately, but instead, wait for the pending operation on the primary
interface to complete. Once that's done, the added extra BSSs will also
be enabled in hostapd_setup_interface_complete().

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-06 15:41:05 +02:00
Jouni Malinen
36501a22a4 hostapd: Verify hostapd_setup_bss calls
Reject multiple calls to hostapd_setup_bss() for any specific interface.
hostapd_cleanup() must have been called first before trying to restart a
BSS.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-06 15:41:05 +02:00
Jouni Malinen
54246f8d44 hostapd: Share a single function for BSS deinit
hostapd_bss_deinit() takes care of freeing the associated stations and
calling hostapd_cleanup() to deinit per-BSS services.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-06 12:48:24 +02:00
Jouni Malinen
6d1ca81ee8 Remove unused hostapd_cleanup_iface_pre()
This has not been used in years and can be removed to clean up the
hostapd deinit path a bit.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-06 12:44:54 +02:00
Jouni Malinen
747c85f932 hostapd: Add more debug prints to deinit path
This makes it easier to follow the various interface/BSS deinit
operations.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-06 12:42:20 +02:00
Jouni Malinen
6023a7880b Restore hapd->interface_added tracking to core hostapd
This reverts parts of commit 390e489c0d
that tried to enable removal of the first BSS. Since that operation is
now forced to remove all BSSs, these changes are not needed. The
hostapd_if_remove() operation in hostapd_free_hapd_data() is problematic
for the first BSS since it ends up freeing driver wrapper information
that is needed later when deinitializing the driver wrapper.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-06 01:38:17 +02:00
Jouni Malinen
486d2ff0eb hostapd: Deinit ctrl_iface in case of add interface failure
Since the control interface is now initialized as part of
hostapd_setup_interface(), it needs to be deinitialized on the error
path.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-06 01:32:55 +02:00
Jouni Malinen
cdf3fb1f1c Fix removal of a BSS that has not yet been fully initialized
If a secondary BSS is removed while it is waiting for the primary BSS to
complete channel setup (e.g., due to HT co-ex scan, ACS, or DFS), the
hostapd_data instance has not yet been initialized. Fix the BSS removal
code to take this special case into account and not try to deinitialize
the hostapd_data instance that has not yet been started.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-06 00:57:38 +02:00
Jouni Malinen
2f99d90726 Remove all BSSs on removal of the first one
The changes in commit 5592065850 to allow
any BSS to be removed were a bit too early since there are still number
of areas that use the first BSS as a special case. Especially the
driver_ops API is going to require quite a bit of cleanup before removal
of the first BSS without the other BSSes of the same radio can be done
safely.

For now, force all BSSs to be removed in case the first one is removed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-06 00:43:10 +02:00
Jouni Malinen
2b6623ab13 hostapd: Do not terminate process on dynamic interface add failure
Limit the calls to eloop_terminate() to happen only for the
initialization failure from the interfaces that we specified on the
command line. This allows hostapd process to continue operating even if
a dynamically added interface fails to start up. This allows the upper
layer software to fix a configuration error and retry.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-05 17:35:11 +02:00
Jouni Malinen
0dfd2c61a5 Document AP mode startup functions
This provides some more details on how interfaces and BSSes are
initialized during hostapd startup.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 21:30:31 +02:00
Jouni Malinen
fee947bfc0 hostapd: Use correct wpa_printf verbosity level for message
This configuration file message is informative and MSG_INFO should be
used instead of MSG_ERROR.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 20:12:36 +02:00
Jouni Malinen
e4ba031531 hostapd: Use start_ctrl_iface() from hostapd_add_iface()
Better share the same function for initializing control interface from
the two possible paths that can add a new interface to hostapd.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
bf7f09bd24 Fix AP mode QoS Map configuration to be per-BSS
This is a per-BSS configuration parameter and as such, needs to be
configured to the driver from hostapd_setup_bss() instead of
hostapd_driver_init().

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
dc036d9ee0 DFS: Convert hostapd_data use to hostapd_iface
DFS operations are specific to the interface (radio/wiphy), not BSS
(netdev/vif), so hostapd_iface is the appropriate element to use in
them.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
2db938e8de hostapd: Fill in phyname automatically
If per-BSS configuration enabling did not provide a phy name, iface->phy
was left empty. It can be helpful to set this up automatically, so fill
that when initializing the interface.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
5ae6449ca2 hostapd: Add ctrl_iface STATUS command
This can be used to fetch runtime information about hostapd interfaces.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
7d6d73701e hostapd: Add AP-ENABLED/DISABLED ctrl_iface events
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
e1c5faf007 hostapd: Track interface state
The new hostapd_iface::state enum is used to track the current state of
the hostapd interface (a radio/wiphy).

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
f0793bf191 hostapd: Wait for channel list update after country code change
If hostapd is requested to set the country code and the previous country
code differs from the new one, the channel list information from the
driver may change. This change may not be instant, so wait for an
EVENT_CHANNEL_LIST_CHANGED event before continuing interface setup with
fetching of the channel list information. This fixes issues where the
selected channel is not available based on the previous regulatory data
and update through CRDA takes some time.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
ad08e1413b hostapd: Move ctrl_iface initialization to happen earlier
Channel determination may take considerable time when ACS or DFS is
used, so it is useful to be able to observe this process through the
control interface. Move the initialization of the control interfaces to
happen before channel determination so that this can be achieved.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
4a5deb9b9d hostapd: Simplify interface initialization
Use hostapd_interface_init2() for all interfaces instead of the
previously used different paths for per-interface-config and
per-BSS-config cases. This moves the calls to hostapd_driver_init() and
hostapd_setup_interface() to happen after all configuration files have
been read.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
71cdf6b624 hostapd: Fix ENABLE failure to not remove interface
Previously, ENABLE command ended up freeing the hostapd_iface context on
initialization failures, but did not even remove the interface from the
list of available interfaces. This resulted in use of freed memory with
any following operation on the same interface. In addition, removing the
interface on initialization failure does not seem like the best
approach. Fix both of these issues by leaving the interface instance in
memory, but in disabled state so that the configuration can be fixed and
ENABLE used again to enable the interface or REMOVE used to remove the
interface.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 11:31:48 +02:00
Jouni Malinen
2aec4f3c0c Allow add-BSS operation to re-use existing netdev
When removing and re-adding the first wlan# netdev to hostapd
dynamically, the netdev is already present and should not be removed and
re-added to maintain its state as not-added-by-hostapd so that it does
not get removed automatically.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 22:34:25 +02:00
Jouni Malinen
5592065850 hostapd: Allow a single BSS to be removed from an interface
The global control interface command "REMOVE <ifname>" can now be used
to remove a single virtual interface (BSS) without affecting other
virtual interfaces on the same radio.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 22:30:15 +02:00
Kyeyoon Park
2e2fff37e9 hostapd: Allow a single BSS to be added to an interface
The global control interface command "ADD
bss_config=<phyname>:<config file>" can now be used to add a single
virtual interface (BSS) to an interface.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 22:30:15 +02:00
Kyeyoon Park
a1fb5692af hostapd: Make hostapd_interface_init_bss() available externally
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 22:00:31 +02:00
Kyeyoon Park
66936c6af8 hostapd: Make hostapd_init() available externally
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 22:00:31 +02:00
Kyeyoon Park
390e489c0d hostapd: Allow the first BSS in a multi-BSS setup to be removed
This moves the vif added check from core hostapd to the driver wrapper
(only driver_nl80211.c uses this) and reorders operations a bit to allow
the first BSS (vif) to be removed from a multi-BSS setup.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 22:00:31 +02:00
Kyeyoon Park
33b0b330ce hostapd: Fix error path in hostapd_add_iface()
Incorrect count variable was used in freeing up the BSS data.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 15:59:12 +02:00
Michal Kazior
813d4bac5a DFS: Add support for multi-BSS
If radar was detected single BSS is notified about it. This caused only
that single BSS to be stopped and restarted. However, due to nl80211
interface combinations the BSS was not started on a new channel and
other BSSes remained operating on the old channel.

The downside is that hostapd_disable_iface() causes deauth frames to be
sent. This is undesired but on the other hand it doesn't make sense to
create workarounds that imitate CSA's 'block tx'. For proper Tx
quiescing CSA should be properly implemented.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
2013-10-31 15:12:17 +02:00
Jouni Malinen
6f2db2fbdd hostapd: Validate configuration parameters on RELOAD command
Reject RELOAD control interface command if the dynamic configuration
changes have resulted into a state where the configuration is invalid.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-29 16:58:21 +02:00
Jouni Malinen
ebd79f07c4 hostapd: Make hostapd_config::bss array of pointers
This makes it more convenient to move BSS configuration entries between
struct hostapd_config instances to clean up per-BSS configuration file
design.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-29 16:58:21 +02:00
Jouni Malinen
a781e211f9 hostapd: Force PSK to be derived again on BSS reload
This may be needed if the wpa_psk information for previously derived
from passphrase and either the SSID or the passphrase has changed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-29 16:58:20 +02:00
Jouni Malinen
9f104b0324 hostapd: Reuse hostapd_clear_old() for RELOAD command
Instead of duplicating the functionality and missing changes (like the
hostapd_broadcast_wep_clear() call), use the hostapd_clear_old()
function that was already used for the similar case with configuration
file reload.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-29 16:09:34 +02:00
Janusz Dziedzic
e76da50529 hostapd: Add AP DFS support
Add DFS structures/events handlers, CAC handling, and radar detection.
By default, after radar is detected or the channel became unavailable, a
random channel will be chosen.

This patches are based on the original work by Boris Presman and
Victor Goldenshtein. Most of the DFS code is moved to a new dfs.c/dfs.h
files.

Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>

Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2013-10-17 21:05:15 +03:00
Jouni Malinen
0249c12596 Avoid compiler warning with CONFIG_NO_STDOUT_DEBUG=y
There is no need to use the bss variable which is used only within a
wpa_printf() call that can be conditionally removed from the build.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-09-25 19:24:17 +03:00
Jouni Malinen
ed1bf011da Allow hostapd config file for dynamically added interface
This extends hostapd global control interface command "ADD" to use a
configuration file instead of requiring configuration to be built using
SET command.

The command format is now following:
ADD <ifname> <control path|config=<path to config>>

For example:

ADD wlan0 /var/run/hostapd
ADD wlan0 config=/tmp/hostapd.conf

When using the configuration file option, ctrl_interface parameter in
the file needs to be set to allow ENABLE command to be issued on the new
interface.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-09-25 19:07:29 +03:00
Jouni Malinen
97bacf7cf6 Do not clear hostapd configuration parameters on disable-iface
There was a comment about the the cleanup steps being from
hostapd_cleanup_iface(). However, the operations that cleared some
security parameters do not seem to exist elsewhere and do not make sense
here. Remove them to avoid changing configuration with DISABLE followed
by ENABLE.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-09-25 18:35:32 +03:00
Michal Kazior
50f4f2a066 hostapd: Add Automatic Channel Selection (ACS) support
This adds ACS support to hostapd. Currently only survey-based
algorithm is available.

To use ACS you need to enable CONFIG_ACS=y in .config and use
channel=0 (or channel=acs_survey) in hostapd.conf.

For more details see wiki page [1] or comments in src/ap/acs.c.

[1]: http://wireless.kernel.org/en/users/Documentation/acs

Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
2013-08-31 11:51:06 +03:00
Michael Braun
d66dcb0d0b WEP: Remove VLAN support from hostapd
This removes WEP with VLAN support and thus avoids increasing
complexity for tagged VLANs.

Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
2013-08-07 12:22:38 +03:00
Sujith Manoharan
3f9a8137f5 hostapd: Add a config option to control beaconing
In a AP/STA concurrent setup, if the STA interface is continually
scanning, trying to connect to a network, the AP interface
is basically broken since beaconing would be erratic.

This option can be used in a WDS setup where one AP acts as a
Client/AP-Repeater. The Repeater AP interface has to start beaconing
only after the Client interface has established a WDS link with the
"Root AP".

Signed-hostap: Sujith Manoharan <c_manoha@qca.qualcomm.com>
2013-07-20 17:20:43 +03:00
Jouni Malinen
3cb953e4b6 Do not set driver MAC ACL unless driver supports this
This cleans up debug log by not including comments about failed
operations in case the operation is known to fail due to not being
supported by the driver.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-24 13:37:22 +03:00
Vivek Natarajan
3c4ca36330 hostapd: Support MAC address based access control list
Enable MAC address based ACL for the drivers which advertise
this capabilty with NL80211_ATTR_MAC_ACL_MAX. Either of blacklist
or whitelist is supported, though, not simultaneously.

Signed-hostap: Vivek Natarajan <nataraja@qca.qualcomm.com>
2013-05-24 13:26:35 +03:00