Some non-mac80211 drivers, such as ath6kl, support STA inactivity timer
in firmware and may not provide connected stations' idle time to the
userspace. If the driver indicates support for offloaded operation, do
not start the inactivity timer in the hostapd.
Signed-hostap: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
struct beacon_data contains a lot of pointers. Make sure it gets cleared
to zero if hostapd_build_beacon_data() gets called from a path that does
not clear the structure first.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The 'started' state was tracked incorrectly. It also broke DFS
as it was using hostapd_enable/disable_iface() functions.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Build CSA settings and call the driver to perform the switch. Construct
Beacon, Probe Response, and (Re)Association Response frames both for CSA
period and for the new channel. These frames are built based on the
current configuration. Add CSA IE in Beacon and Probe Response frames.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
We were not filtering the EVENT_CHANNEL_LIST_CHANGED events based on the
regulatory hint initiator. So wait for EVENT_CHANNEL_LIST_CHANGED event
after our own change was triggered even when regulatory hint initiator
was the driver. This could result in the wait for the channel list to be
updated to be terminated before the real change has occurred and as
such, old channel list remaining in use when configuring
hostapd/wpa_supplicant country parameter. Fix this by filtering the
hints according to the initiator and only regulatory hints initiated by
user will be used to stop the wait.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for additional BSSs to be added while the primary
interface is still in the process of determining channel parameters (HT
co-ex scan, ACS, DFS). Do not enable secondary interfaces in such state
immediately, but instead, wait for the pending operation on the primary
interface to complete. Once that's done, the added extra BSSs will also
be enabled in hostapd_setup_interface_complete().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Reject multiple calls to hostapd_setup_bss() for any specific interface.
hostapd_cleanup() must have been called first before trying to restart a
BSS.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd_bss_deinit() takes care of freeing the associated stations and
calling hostapd_cleanup() to deinit per-BSS services.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This reverts parts of commit 390e489c0d
that tried to enable removal of the first BSS. Since that operation is
now forced to remove all BSSs, these changes are not needed. The
hostapd_if_remove() operation in hostapd_free_hapd_data() is problematic
for the first BSS since it ends up freeing driver wrapper information
that is needed later when deinitializing the driver wrapper.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the control interface is now initialized as part of
hostapd_setup_interface(), it needs to be deinitialized on the error
path.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a secondary BSS is removed while it is waiting for the primary BSS to
complete channel setup (e.g., due to HT co-ex scan, ACS, or DFS), the
hostapd_data instance has not yet been initialized. Fix the BSS removal
code to take this special case into account and not try to deinitialize
the hostapd_data instance that has not yet been started.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The changes in commit 5592065850 to allow
any BSS to be removed were a bit too early since there are still number
of areas that use the first BSS as a special case. Especially the
driver_ops API is going to require quite a bit of cleanup before removal
of the first BSS without the other BSSes of the same radio can be done
safely.
For now, force all BSSs to be removed in case the first one is removed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Limit the calls to eloop_terminate() to happen only for the
initialization failure from the interfaces that we specified on the
command line. This allows hostapd process to continue operating even if
a dynamically added interface fails to start up. This allows the upper
layer software to fix a configuration error and retry.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Better share the same function for initializing control interface from
the two possible paths that can add a new interface to hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a per-BSS configuration parameter and as such, needs to be
configured to the driver from hostapd_setup_bss() instead of
hostapd_driver_init().
Signed-hostap: Jouni Malinen <j@w1.fi>
DFS operations are specific to the interface (radio/wiphy), not BSS
(netdev/vif), so hostapd_iface is the appropriate element to use in
them.
Signed-hostap: Jouni Malinen <j@w1.fi>
If per-BSS configuration enabling did not provide a phy name, iface->phy
was left empty. It can be helpful to set this up automatically, so fill
that when initializing the interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
If hostapd is requested to set the country code and the previous country
code differs from the new one, the channel list information from the
driver may change. This change may not be instant, so wait for an
EVENT_CHANNEL_LIST_CHANGED event before continuing interface setup with
fetching of the channel list information. This fixes issues where the
selected channel is not available based on the previous regulatory data
and update through CRDA takes some time.
Signed-hostap: Jouni Malinen <j@w1.fi>
Channel determination may take considerable time when ACS or DFS is
used, so it is useful to be able to observe this process through the
control interface. Move the initialization of the control interfaces to
happen before channel determination so that this can be achieved.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use hostapd_interface_init2() for all interfaces instead of the
previously used different paths for per-interface-config and
per-BSS-config cases. This moves the calls to hostapd_driver_init() and
hostapd_setup_interface() to happen after all configuration files have
been read.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, ENABLE command ended up freeing the hostapd_iface context on
initialization failures, but did not even remove the interface from the
list of available interfaces. This resulted in use of freed memory with
any following operation on the same interface. In addition, removing the
interface on initialization failure does not seem like the best
approach. Fix both of these issues by leaving the interface instance in
memory, but in disabled state so that the configuration can be fixed and
ENABLE used again to enable the interface or REMOVE used to remove the
interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
When removing and re-adding the first wlan# netdev to hostapd
dynamically, the netdev is already present and should not be removed and
re-added to maintain its state as not-added-by-hostapd so that it does
not get removed automatically.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The global control interface command "REMOVE <ifname>" can now be used
to remove a single virtual interface (BSS) without affecting other
virtual interfaces on the same radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The global control interface command "ADD
bss_config=<phyname>:<config file>" can now be used to add a single
virtual interface (BSS) to an interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This moves the vif added check from core hostapd to the driver wrapper
(only driver_nl80211.c uses this) and reorders operations a bit to allow
the first BSS (vif) to be removed from a multi-BSS setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If radar was detected single BSS is notified about it. This caused only
that single BSS to be stopped and restarted. However, due to nl80211
interface combinations the BSS was not started on a new channel and
other BSSes remained operating on the old channel.
The downside is that hostapd_disable_iface() causes deauth frames to be
sent. This is undesired but on the other hand it doesn't make sense to
create workarounds that imitate CSA's 'block tx'. For proper Tx
quiescing CSA should be properly implemented.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Reject RELOAD control interface command if the dynamic configuration
changes have resulted into a state where the configuration is invalid.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it more convenient to move BSS configuration entries between
struct hostapd_config instances to clean up per-BSS configuration file
design.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This may be needed if the wpa_psk information for previously derived
from passphrase and either the SSID or the passphrase has changed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of duplicating the functionality and missing changes (like the
hostapd_broadcast_wep_clear() call), use the hostapd_clear_old()
function that was already used for the similar case with configuration
file reload.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add DFS structures/events handlers, CAC handling, and radar detection.
By default, after radar is detected or the channel became unavailable, a
random channel will be chosen.
This patches are based on the original work by Boris Presman and
Victor Goldenshtein. Most of the DFS code is moved to a new dfs.c/dfs.h
files.
Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
There is no need to use the bss variable which is used only within a
wpa_printf() call that can be conditionally removed from the build.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This extends hostapd global control interface command "ADD" to use a
configuration file instead of requiring configuration to be built using
SET command.
The command format is now following:
ADD <ifname> <control path|config=<path to config>>
For example:
ADD wlan0 /var/run/hostapd
ADD wlan0 config=/tmp/hostapd.conf
When using the configuration file option, ctrl_interface parameter in
the file needs to be set to allow ENABLE command to be issued on the new
interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There was a comment about the the cleanup steps being from
hostapd_cleanup_iface(). However, the operations that cleared some
security parameters do not seem to exist elsewhere and do not make sense
here. Remove them to avoid changing configuration with DISABLE followed
by ENABLE.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds ACS support to hostapd. Currently only survey-based
algorithm is available.
To use ACS you need to enable CONFIG_ACS=y in .config and use
channel=0 (or channel=acs_survey) in hostapd.conf.
For more details see wiki page [1] or comments in src/ap/acs.c.
[1]: http://wireless.kernel.org/en/users/Documentation/acs
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
In a AP/STA concurrent setup, if the STA interface is continually
scanning, trying to connect to a network, the AP interface
is basically broken since beaconing would be erratic.
This option can be used in a WDS setup where one AP acts as a
Client/AP-Repeater. The Repeater AP interface has to start beaconing
only after the Client interface has established a WDS link with the
"Root AP".
Signed-hostap: Sujith Manoharan <c_manoha@qca.qualcomm.com>
This cleans up debug log by not including comments about failed
operations in case the operation is known to fail due to not being
supported by the driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Enable MAC address based ACL for the drivers which advertise
this capabilty with NL80211_ATTR_MAC_ACL_MAX. Either of blacklist
or whitelist is supported, though, not simultaneously.
Signed-hostap: Vivek Natarajan <nataraja@qca.qualcomm.com>
